STOP AND START SYSTEM, Diagnostic DTC:P323B

DTC Code DTC Name
P323B Backup Boost Converter

DESCRIPTION

Refer to DTC B22C0

Click hereClick here

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

Warning Indicate

Memory

P323B

Backup Boost Converter

Any of the following conditions are met for 1 second or more (1 trip detection logic):

  • BBC malfunction is detected

  • Engine stop and start ECU thermistor temperature is 128°C (262.4°F) or higher

  • Difference in temperature between thermistor 1 and thermistor 2 of the engine stop and start ECU is 40°C (104°F) or higher

  • BO1 voltage is 6.0 V or less and BBC is not overheating

  • IGO1 voltage is 6.0 V or less

  • Engine stop and start ECU

  • Wire harness or connector

  • Battery

  • BBC fuse

Blinks

DTC stored

CONFIRMATION DRIVING PATTERN

Tip:

DTCs for the stop and start system are not cleared automatically even if the malfunction has been repaired. After repairing the malfunction, be sure to clear the DTCs.

Click here

  1. Tip:

    • If the cable is disconnected from the negative (-) battery terminal, stop and start control is prohibited until refresh charge is completed. In this case, drive the vehicle approximately 5 to 40 minutes until refresh charge is completed and stop and start control operation is permitted.

    • Allow the engine to idle for 3 minutes after it is warmed up and check that the engine idle speed is within 50 rpm of the target idle speed.

    CONFIRMATION AFTER TROUBLESHOOTING

    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON and turn the GTS on.

    3. Clear the DTCs.

      Click here

      Powertrain > Stop and Start > Clear DTCs

    4. Start the engine and warm it up.

    5. Drive the vehicle at 7 km/h (4.3 mph) or more.

      CAUTION:

      When performing Confirmation Driving Pattern, obey all speed limits and traffic laws.

    6. Stop the vehicle, move the shift lever to neutral and release the clutch pedal. (for Manual Transaxle)

    7. Depress the brake pedal and stop the vehicle. (for CVT)

    8. Keep the engine stopped by stop and start control for 1 second or more. (Keep the shift lever in D. (for CVT))

    9. Depress the clutch pedal and start the engine. (for Manual Transaxle)

      Tip:

      If the engine cranks slowly when the engine is restarted, it can be determined that the battery voltage is low.

    10. Release the brake pedal with the shift lever in D to start the engine. (for CVT)

      Tip:

      If the engine cranks slowly when the engine is restarted, it can be determined that the battery voltage is low.

    11. Check that DTCs are not output.

      Click here

      Powertrain > Stop and Start > Trouble Codes

  2. STOP AND START SYSTEM OPERATION CHECK

    Tip:

    If the cable is disconnected from the negative (-) battery terminal, stop and start control is prohibited until refresh charge is completed. In this case, drive the vehicle approximately 5 to 40 minutes until refresh charge is completed and stop and start control operation is permitted.

    1. Start the engine and warm it up.

    2. Turn the air conditioning system off.

    3. Drive the vehicle at 7 km/h (4.3 mph) or more.

      CAUTION:

      When performing Confirmation Driving Pattern, obey all speed limits and traffic laws.

    4. Stop the vehicle, move the shift lever to neutral and release the clutch pedal. (for Manual Transaxle)

    5. Depress the brake pedal and stop the vehicle. (for CVT)

    6. Allow the engine to stop by stop and start control. (Keep the shift lever in D. (for CVT))

    7. Depress the clutch pedal and start the engine. (for Manual Transaxle)

    8. Release the brake pedal with the shift lever in D to start the engine. (for CVT)

WIRING DIAGRAM

Refer to DTC B22C0.

Click hereClick here

CAUTION / NOTICE / HINT

Note:

  • Before replacing the engine stop and start ECU, read the number of starter operations and write it into a new engine stop and start ECU.

    Click here

  • After replacing the engine stop and start ECU or air conditioning amplifier assembly, reset and perform learning of the air conditioning information in the engine stop and start ECU.

    Click here

  • After replacing the engine stop and start ECU or airbag sensor assembly, clear and calibrate the deceleration sensor zero point in the engine stop and start ECU.

    Click here

  • Inspect the fuses for circuits related to this system before performing the following procedure.

Tip:

Using the GTS, read the freeze frame data before troubleshooting. System condition information is recorded as freeze frame data the moment a DTC is stored. This information can be useful when troubleshooting.

Click here

PROCEDURE

  1. CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - BBC FUSE)

    Click hereClick here

    Result

    Proceed to

    OK

    NG
    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  2. CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU POWER SOURCE CIRCUIT)

    1. A285704C04

      *a

      Front view of wire harness connector:

      (to Engine Stop and Start ECU)

      Disconnect the A8 and E24 engine stop and start ECU connectors.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection

      Condition

      Specified Condition

      A8-7 (BIN) - Body ground

      Always

      9.5 to 14 V

    3. Turn the ignition switch to ON.

    4. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection

      Condition

      Specified Condition

      E24-17 (IG1) - Body ground

      Ignition switch ON

      9.5 to 14 V

    Result

    Proceed to

    OK

    NG
    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  3. CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - BODY GROUND)

    1. Disconnect the A8 engine stop and start ECU connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      A8-8 (GND) - Body ground

      Always

      Below 1 Ω

    Result

    Proceed to

    OK

    NG
    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  4. CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)

    Click hereClick here

    Result

    Proceed to

    OK

    NG
    OK

    REPLACE ENGINE STOP AND START ECU

    Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR