SPEED LIMITER SYSTEM DATA LIST / ACTIVE TEST

  1. DATA LIST

    Tip:

    Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

    Note:

    In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. for 1NR-FE, 1ZR-FAE, 1ND-TV:

      Enter the following menus: Powertrain / Cruise Control / Data List.

    5. for 1NR-FE, 1ZR-FAE, 1ND-TV:

      Read the Data List according to the display on the GTS.

      Powertrain > Cruise Control > Data List

      Tester Display

      Measurement Item

      Range

      Normal Condition

      Diagnostic Note

      ASL Vehicle Speed

      Vehicle speed

      Min.: 0 km/h (0 mph), Max.: 255 km/h (159 mph)

      Actual vehicle speed displayed

      -

      ASL Memory Vehicle Speed

      Vehicle speed

      Min.: 0 km/h (0 mph), Max.: 255 km/h (159 mph)

      Vehicle speed stored in memory

      -

      ASL Throttle Position

      Throttle opening angle

      Min.: 0 deg., Max.: 124.5 deg

      Required throttle opening angle

      -

      ASL Ready

      Speed limit standby condition

      ON or OFF

      OFF: Speed limiter switch off

      ON: Speed limiter switch on

      -

      ASL Main Switch

      Speed limiter switch signal

      ON or OFF

      OFF: Speed limiter switch off

      ON: Speed limiter switch on

      -

      ASL Shift Position Request

      Transaxle gear request signal

      Min.: 0, Max.: 8

      Required transaxle gear

      -
      Tip:

      ASL Shift Position Request: for CVT

    6. for 8NR-FTS:

      Enter the following menus: Powertrain / Engine / Data List.

    7. for 8NR-FTS:

      Read the Data List according to the display on the GTS.

      Powertrain > Engine > Data List

      Tester Display

      Measurement Item

      Range

      Normal Condition

      Diagnostic Note

      ASL SW

      Speed limiter switch signal

      ON or OFF

      OFF: Speed limiter switch off

      ON: Speed limiter switch on

      -

      ASL Vehicle Speed

      Vehicle speed

      Min.: 0 km/h (0 mph), Max.: 255 km/h (159 mph)

      Actual vehicle speed displayed

      -

      ASL Memory Vehicle Speed

      Vehicle speed

      Min.: 0 km/h (0 mph), Max.: 255 km/h (159 mph)

      Vehicle speed stored in memory

      -

      ASL Request Limit Driving Force

      Speed limiter request limit driving force

      Min.: -10 kN, Max.: 9.92 kN

      -

      -

      ASL Request Gear Position

      Transaxle gear request signal

      0 to 255 Gear

      Required transaxle gear

      -

      TRC/VSC OFF Indicator

      TRC/VSC OFF indicator signal

      ON or OFF

      OFF: TRC/VSC OFF indicator not illuminated

      ON: TRC/VSC OFF indicator illuminated

      -

      ASL Cancel History (Lost Communication with Brake System)

      Speed limiter cancel history (lost communication with brake system)

      ON or OFF

      OFF: Speed limiter cancel history (lost communication with brake system) does not exist

      ON: Speed limiter cancel history (lost communication with brake system) exists

      -

      ASL Cancel History (Speed Sensor Malfunction)

      Speed limiter cancel history (speed sensor malfunction)

      ON or OFF

      OFF: Speed limiter cancel history (speed sensor malfunction) does not exist

      ON: Speed limiter cancel history (speed sensor malfunction) exists

      -

      Kickdown Switch

      Kickdown Switch signal

      ON or OFF

      OFF: Accelerator pedal released

      ON: Accelerator pedal fully depressed

      -

      ASL Limiting Driving Force

      ASL limiting driving force operation condition

      Inactive or Active

      Active: ASL limiting driving force is operating

      Inactive: ASL limiting driving force is not operating

      -

      ASL Ready

      Speed limit standby condition

      ON or OFF

      OFF: Speed limiter switch off

      ON: Speed limiter switch on

      -
      Tip:

      ASL Request Gear Position: for CVT

  2. ACTIVE TEST (for Multi-information Display (Segment LCD Type))

    Tip:

    Using the GTS to perform Active Tests allows relays, VSVs, actuators and other item to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Combination Meter / Active Test.

    5. Perform "Active Test" according to the display on GTS.

      Body Electrical > Combination Meter > Active Test

      Tester Display

      Measurement Item

      Control Range

      Diagnostic Note

      Indicat. ASL

      Adjustable speed limiter indicator light (Green)

      OFF or ON

      -

      ASL Warning Indicator

      Adjustable speed limiter indicator light (Yellow)

      OFF or ON

      -