LOWER INSTRUMENT PANEL REMOVAL

CAUTION / NOTICE / HINT

Tip:

  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

PROCEDURE

  1. TABLE OF BOLT, SCREW AND NUT

    Tip:

    All bolts, screws and nuts relevant to installing and removing the instrument panel are shown along with their alphabet code in the table below.

    B339755E01

  2. PRECAUTION

    Note:

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

    Click here

  3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Note:

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  4. REMOVE UPPER INSTRUMENT PANEL

    Click here

  5. REMOVE REAR CONSOLE BOX SUB-ASSEMBLY

    Click here

  6. REMOVE LOWER NO. 2 INSTRUMENT PANEL FINISH PANEL

    1. B337813

      Detach the 8 clips and remove the lower No. 2 instrument panel finish panel.

    2. B337815C01

      *1

      w/ Drive Mode Switch

      *2

      w/ Seat Heater System

      *3

      w/ PTC Heater

      *4

      for Windshield Deicer

      *5

      w/ USB Audio System

      for LHD:

      Disconnect each connector.

    3. B337816C01

      *1

      w/ USB Audio System

      *2

      w/ Seat Heater System

      *3

      w/ Drive Mode Switch

      for RHD:

      Disconnect each connector.

  7. REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

    1. B337814

      Remove the 2 screws <A> or <B>.

    2. Detach the 2 claws and 2 guides and remove the No. 1 instrument panel under cover sub-assembly.

    3. w/ Tire Pressure Warning System:

      Disconnect the connector.

  8. REMOVE FUSE BOX OPENING COVER

    1. B337819C01
      V100155

      Protective Tape

      for LHD:

      1. Apply protective tape as shown in the illustration.

      2. Detach the 8 clips and remove the fuse box opening cover.

      3. B337821C01

        *1

        w/ Headlight Leveling

        *2

        w/ Light Control Rheostat

        *3

        w/ VSC OFF Switch

        *4

        w/ Blind Spot Monitor

        Disconnect each connector and detach the wire harness clamp.

    2. B337817C01
      V100155

      Protective Tape

      for RHD:

      1. Apply protective tape as shown in the illustration.

      2. Detach the 9 clips and remove the fuse box opening cover.

      3. B337822C01

        *1

        w/ VSC OFF Switch

        *2

        w/ Headlight Leveling

        Disconnect each connector.

  9. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL (for LHD without Driver Side Knee Airbag)

    1. B337824C01
      V100155

      Protective Tape

      Apply protective tape as shown in the illustration.

    2. Detach the 4 clips and 4 claws and remove the lower instrument panel finish panel.

  10. REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (w/ Driver Side Knee Airbag)

    Click here

  11. REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

    1. B337823

      Detach the 2 claws and 2 guides and remove the No. 2 instrument panel under cover sub-assembly.

  12. REMOVE FRONT DOOR SCUFF PLATE LH

    Click here

  13. REMOVE FRONT DOOR SCUFF PLATE RH

    Click here

  14. REMOVE COWL SIDE TRIM BOARD LH

    1. B337827

      Remove the nut.

    2. Detach the clip and remove the cowl side trim board LH.

  15. REMOVE COWL SIDE TRIM BOARD RH

    Tip:

    Use the same procedure described for the LH side.

  16. REMOVE DEFROSTER NOZZLE ASSEMBLY

    1. B337828

      Disconnect the connector and detach the 2 wire harness clamps.

    2. Detach the 3 claws and remove the defroster nozzle assembly.

  17. REMOVE HEATER TO REGISTER DUCT ASSEMBLY

    1. B337829

      Remove the 2 clips.

    2. Pull up the heater to register duct assembly to detach the 6 claws and remove it.

  18. REMOVE LOWER INSTRUMENT PANEL (for LHD)

    1. Disconnect each connector and detach each wire harness clamp.

    2. Detach the claw and disconnect the hood lock control lever.

    3. Detach the 2 claws and disconnect the DLC3.

    4. Detach the 2 claws and disconnect the cooler thermistor.

      B337831C01

      *A

      for 4WD/AWD

      *B

      w/ Power Back Door

      *C

      w/ Downhill Assist Control

      *D

      w/ Entry and Start System

    5. Remove the 6 bolts <E> or <F> and 2 bolts <C> or <D>.

    6. Remove the bolt <G> and lower instrument panel.

      B337832C02

      *1

      Bolt <E> or <F>

      *2

      Bolt <C> or <D>

      *3

      Bolt <G>

      -

      -

  19. REMOVE LOWER INSTRUMENT PANEL (for RHD)

    1. Disconnect each connector and detach each wire harness clamp.

    2. Detach the claw and disconnect the hood lock control lever.

    3. Detach the 2 claws and disconnect the DLC3.

    4. Detach the 2 claws and disconnect the cooler thermistor.

      B340246C01

      *A

      for 4WD/AWD

      *B

      w/ Power Back Door

      *C

      w/ Downhill Assist Control

      *D

      w/ Entry and Start System

    5. Remove the 7 bolts <E> or <F> and 2 bolts <C> or <D>.

    6. Remove the bolt <G> and lower instrument panel.

      B340247C01

      *1

      Bolt <E> or <F>

      *2

      Bolt <C> or <D>

      *3

      Bolt <G>

      -

      -