FRONT DOOR LOCK INSPECTION

PROCEDURE

1. INSPECT FRONT DOOR WITH MOTOR LOCK ASSEMBLY LH (w/o Double Locking System)

   1. 

      *a	Component without harness connected (Front Door with Motor Lock Assembly LH)
      *b	Unlock
      *c	Lock

      Check the operation of the front door lock motor.

      1. Apply battery voltage and check the operation of the front door lock motor.

         OK

         Measurement Condition	Specified Condition
         Battery positive (+) → 4 (L) Battery negative (-) → 1 (UL)	Locks
         Battery positive (+) → 1 (UL) Battery negative (-) → 4 (L)	Unlocks

         If the result is not as specified, replace the front door with motor lock assembly LH.

   2. 

      *a	Component without harness connected (Front Door with Motor Lock Assembly LH)
      *b	Unlock
      *c	Lock

      Check the operation of the door unlock detection switch (w/ Smart Entry and Start System or Theft Deterrent System).

      1. Measure the resistance according to the value(s) in the table below.

         Standard Resistance

         Tester Connection	Condition	Specified Condition
         7 (E) - 8 (LSSR)	Locked	10 kΩ or higher
         	Unlocked	Below 1 Ω

         If the result is not as specified, replace the front door with motor lock assembly LH.

   3. 

      *a	Component without harness connected (Front Door with Motor Lock Assembly LH)
      *b	Unlock
      *c	Lock

      Check the operation of the door key lock and unlock switch (for LHD).

      1. Measure the resistance according to the value(s) in the table below.

         Standard Resistance

         Tester Connection	Condition	Specified Condition
         9 (L) - 7 (E)	Held to lock side	Below 1 Ω
         9 (L) - 7 (E)	Neutral or held to unlock side	10 kΩ or higher
         10 (UL) - 7 (E)	Held to unlock side	Below 1 Ω
         10 (UL) - 7 (E)	Neutral or held to lock side	10 kΩ or higher

         If the result is not as specified, replace the front door with motor lock assembly LH.

2. INSPECT FRONT DOOR WITH MOTOR LOCK ASSEMBLY LH (w/ Double Locking System)

   1. 

      *a	Component without harness connected (Front Door with Motor Lock Assembly LH)
      *b	Unlock
      *c	Lock

      Check the operation of the front door lock motor.

      1. Apply battery voltage and check the operation of the front door lock motor and double lock motor.

         OK

         Measurement Condition	Specified Condition
         Battery positive (+) → 4 (L) Battery negative (-) → 3 (UL)	Locks
         Battery positive (+) → 3 (UL) Battery negative (-) → 4 (L)	Unlocks
         Battery positive (+) → 2 (DL) Battery negative (-) → 1 (UNDL)	Sets
         Battery positive (+) → 1 (UNDL) Battery negative (-) → 2 (DL)	Unsets

         Tip:

         • Move the door lock motor to the lock position and set the double locking system. Check that the doors cannot be unlocked by operating the control cable.

         • Move the door lock motor to the lock position and unset the double locking system. Check that the doors can be unlocked by operating the control cable.

         If the result is not as specified, replace the front door with motor lock assembly LH.

   2. 

      *a	Component without harness connected (Front Door with Motor Lock Assembly LH)
      *b	Unlock
      *c	Lock

      Check the operation of the door unlock detection switch and double lock position switch.

      1. Measure the resistance according to the value(s) in the table below.

         Standard Resistance

         Tester Connection	Condition	Specified Condition
         8 (LSSR) - 7 (E)	Locked	10 kΩ or higher
         8 (LSSR) - 7 (E)	Unlocked	Below 1 Ω
         6 (DLSR) - 5 (E)	Unset	10 kΩ or higher
         6 (DLSR) - 5 (E)	Set	Below 1 Ω

         If the result is not as specified, replace the front door with motor lock assembly LH.

3. INSPECT FRONT DOOR WITH MOTOR LOCK ASSEMBLY RH (w/o Double Locking System)

   1. 

      *a	Component without harness connected (Front Door with Motor Lock Assembly RH)
      *b	Unlock
      *c	Lock

      Check the operation of the front door lock motor.

      1. Apply battery voltage and check the operation of the front door lock motor.

         OK

         Measurement Condition	Specified Condition
         Battery positive (+) → 4 (L) Battery negative (-) → 1 (UL)	Locks
         Battery positive (+) → 1 (UL) Battery negative (-) → 4 (L)	Unlocks

         If the result is not as specified, replace the front door with motor lock assembly RH.

   2. 

      *a	Component without harness connected (Front Door with Motor Lock Assembly RH)
      *b	Unlock
      *c	Lock

      Check the operation of the door unlock detection switch.

      1. Measure the resistance according to the value(s) in the table below.

         Standard Resistance

         Tester Connection	Condition	Specified Condition
         7 (LSSR) - 8 (E)	Locked	10 kΩ or higher
         7 (LSSR) - 8 (E)	Unlocked	Below 1 Ω

         If the result is not as specified, replace the front door with motor lock assembly RH.

   3. 

      *a	Component without harness connected (Front Door with Motor Lock Assembly RH)
      *b	Unlock
      *c	Lock

      Check the operation of the door key lock and unlock switch (for RHD).

      1. Measure the resistance according to the value(s) in the table below.

         Standard Resistance

         Tester Connection	Condition	Specified Condition
         6 (L) - 8 (E)	Held to lock side	Below 1 Ω
         6 (L) - 8 (E)	Neutral or held to unlock side	10 kΩ or higher
         5 (UL) - 8 (E)	Held to unlock side	Below 1 Ω
         5 (UL) - 8 (E)	Neutral or held to lock side	10 kΩ or higher

         If the result is not as specified, replace the front door with motor lock assembly RH.

4. INSPECT FRONT DOOR WITH MOTOR LOCK ASSEMBLY RH (w/ Double Locking System)

   1. 

      *a	Component without harness connected (Front Door with Motor Lock Assembly RH)
      *b	Unlock
      *c	Lock

      Check the operation of the front door lock motor.

      1. Apply battery voltage and check the operation of the front door lock motor and double lock motor.

         OK

         Measurement Condition	Specified Condition
         Battery positive (+) → 2 (L) Battery negative (-) → 1 (UL)	Locks
         Battery positive (+) → 1 (UL) Battery negative (-) → 2 (L)	Unlocks
         Battery positive (+) → 4 (DL) Battery negative (-) → 3 (UNDL)	Sets
         Battery positive (+) → 3 (UNDL) Battery negative (-) → 4 (DL)	Unsets

         Tip:

         • Move the door lock motor to the lock position and set the double locking system. Check that the doors cannot be unlocked by operating the control cable.

         • Move the door lock motor to the lock position and unset the double locking system. Check that the doors can be unlocked by operating the control cable.

         If the result is not as specified, replace the front door with motor lock assembly RH.

   2. 

      *a	Component without harness connected (Front Door with Motor Lock Assembly RH)
      *b	Unlock
      *c	Lock

      Check the operation of the door unlock detection switch and double lock position switch.

      1. Measure the resistance according to the value(s) in the table below.

         Standard Resistance

         Tester Connection	Condition	Specified Condition
         7 (LSSR) - 8 (E)	Locked	10 kΩ or higher
         7 (LSSR) - 8 (E)	Unlocked	Below 1 Ω
         9 (DLSR) - 10 (E)	Unset	10 kΩ or higher
         9 (DLSR) - 10 (E)	Set	Below 1 Ω

         If the result is not as specified, replace the front door with motor lock assembly RH.

   3. 

      *a	Component without harness connected (Front Door with Motor Lock Assembly RH)
      *b	Unlock
      *c	Lock

      Check the operation of the door key lock and unlock switch.

      1. Measure the resistance according to the value(s) in the table below.

         Standard Resistance

         Tester Connection	Condition	Specified Condition
         6 (L) - 8 (E)	Held to lock side	Below 1 Ω
         6 (L) - 8 (E)	Neutral or held to unlock side	10 kΩ or higher
         5 (UL) - 8 (E)	Held to unlock side	Below 1 Ω
         5 (UL) - 8 (E)	Neutral or held to lock side	10 kΩ or higher

         If the result is not as specified, replace the front door with motor lock assembly RH.