ECD SYSTEM, Diagnostic DTC:P011C

DTC Code DTC Name
P011C Charge Air Temperature/Intake Air Temperature Correlation (Bank 1)

DESCRIPTION

Refer to DTC P007C.

Click here

Refer to DTC P0112.

Click here

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

MIL

Memory

P011C

Charge Air Temperature/Intake Air Temperature Correlation (Bank 1)

After the engine is completely warmed up and then allowed to soak for a long time (10 hours or more), the difference in temperature at the intake air temperature sensor and intake air temperature sensor (turbo) after turbocharger after idling for 3 minutes is 15°C (27°F) or higher (2 trip detection logic).

  • Open or short in intake air temperature sensor circuit

  • Open or short in intake air temperature sensor (turbo) circuit

  • Intake air temperature sensor (built into mass air flow meter assembly)

  • Intake air temperature sensor (turbo)

  • ECM

Comes on

DTC stored
Table 1. Related Data List

DTC No.

Data List

P011C

  • Intake Air

  • Intake Air Temp (Turbo)

CONFIRMATION DRIVING PATTERN

DTC No.

DTC Detection Drive Pattern

P011C

After engine completely warmed up, allow engine to soak for long time (10 hours or more).

Start the engine and idle the engine for 3 minutes or more.

WIRING DIAGRAM

Refer to DTC P007C for intake air temperature sensor (turbo) circuit.

Click here

Refer to DTC P0112 for intake air temperature sensor circuit.

Click here

CAUTION / NOTICE / HINT

Note:

After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).

Tip:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

PROCEDURE

  1. CHECK DTC OUTPUT (IN ADDITION TO DTC P011C)

    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON and turn the GTS on.

    3. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

    4. Read the DTCs.

      Powertrain > Engine > Trouble Codes

      Result

      Result

      Proceed to

      DTC P011C is output

      A

      DTC P011C and other DTCs are output

      B
      Tip:

      If any DTCs other than P011C are output, troubleshoot those DTCs first.

    B

    GO TO DTC CHART

    Click hereClick here

    A

  2. READ VALUE USING GTS (COOLANT TEMP)

    1. Allow the engine to soak for 1 to 2 hours.

      Tip:

      • It is not necessary to allow the engine to soak if the engine is cold.

      • The engine cools faster if the hood is opened.

    2. Connect the GTS to the DLC3.

    3. Turn the ignition switch to ON and turn the GTS on.

    4. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Coolant Temp.

      Powertrain > Engine > Data List

      Tester Display

      Coolant Temp

    5. Read the value.

      OK

      The difference between the displayed value and ambient temperature is below 5°C (9°F).

      Note:

      If the difference between "Coolant Temp" and the ambient temperature is 5°C (9°F) or higher, the heat from the engine affects the intake air temperature sensor, causing an incorrect value to be displayed. In this case, allow the engine to soak again.

    Result

    Proceed to

    NEXT
    NEXT

  3. READ VALUE USING GTS (INTAKE AIR)

    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON and turn the GTS on.

    3. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Intake Air.

      Powertrain > Engine > Data List

      Tester Display

      Intake Air

    4. Read the value.

      OK

      The difference between the displayed value and ambient temperature is below 15°C (27°F).

    Result

    Proceed to

    OK

    NG
    NG

    CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER ASSEMBLY - ECM)Click here

    OK

  4. READ VALUE USING GTS (INTAKE AIR TEMP (TURBO))

    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON and turn the GTS on.

    3. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Intake Air Temp (Turbo).

      Powertrain > Engine > Data List

      Tester Display

      Intake Air Temp (Turbo)

    4. Read the value.

      OK

      The difference between the displayed value and ambient temperature is below 15°C (27°F).

    Result

    Proceed to

    OK

    NG
    NG

    CHECK HARNESS AND CONNECTOR (INTAKE AIR TEMPERATURE SENSOR (TURBO) - ECM)Click here

    OK

  5. REPLACE ECM

    1. Replace the ECM.

      Click here

    Result

    Proceed to

    NEXT
    NEXT

    CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIREDClick here

  6. CHECK HARNESS AND CONNECTOR (INTAKE AIR TEMPERATURE SENSOR (TURBO) - ECM)

    1. Disconnect the intake air temperature sensor (turbo) connector.

    2. Disconnect the ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      A54-2 - B76-113 (THIA)

      Always

      Below 1 Ω

      A54-1 - B76-90 (ETHI)

      Always

      Below 1 Ω

      A54-2 or B76-113 (THIA) - Body ground

      Always

      10 kΩ or higher

    Result

    Proceed to

    OK

    NG
    NG

    REPAIR OR REPLACE HARNESS AND CONNECTORClick here

    OK

  7. REPLACE INTAKE AIR TEMPERATURE SENSOR (TURBO)

    1. Replace the intake air temperature sensor (turbo).

      Click here

    Result

    Proceed to

    NEXT
    NEXT

    CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIREDClick here

  8. CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER ASSEMBLY - ECM)

    1. Disconnect the mass air flow meter assembly connector.

    2. Disconnect the ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      B1-4 (THA) - B76-110 (THA)

      Always

      Below 1 Ω

      B1-5 (E2) - B76-87 (ETHA)

      Always

      Below 1 Ω

      B1-4 (THA) or B76-110 (THA) - Body ground

      Always

      10 kΩ or higher

    Result

    Proceed to

    OK

    NG
    NG

    REPAIR OR REPLACE HARNESS AND CONNECTORClick here

    OK

  9. REPLACE MASS AIR FLOW METER ASSEMBLY

    1. Replace the mass air flow meter assembly.

      Click here

    Result

    Proceed to

    NEXT
    NEXT

    CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIREDClick here

  10. REPAIR OR REPLACE HARNESS AND CONNECTOR

    1. Repair or replace the harness or connector.

    Result

    Proceed to

    NEXT
    NEXT

  11. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

    1. Allow the engine to soak for 1 to 2 hours.

      Tip:

      • It is not necessary to allow the engine to soak if the engine is cold.

      • The engine cools faster if the hood is opened.

    2. Connect the GTS to the DLC3.

    3. Turn the ignition switch to ON and turn the GTS on.

    4. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Coolant Temp.

      Powertrain > Engine > Data List

      Tester Display

      Coolant Temp

    5. Read the value.

      Note:

      If the difference between "Coolant Temp" and the ambient temperature is 5°C (9°F) or higher, the heat from the engine affects the intake air temperature sensor, causing an incorrect value to be displayed. In this case, allow the engine to soak again.

    6. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Intake Air and Intake Air Temp (Turbo).

      Powertrain > Engine > Data List

      Tester Display

      Intake Air

      Intake Air Temp (Turbo)

    7. Read the value.

      OK

      The difference between the displayed value and ambient temperature is below 15°C (27°F).

    Result

    Proceed to

    NEXT
    NEXT

    END