ENGINE ASSEMBLY COMPONENTS
ILLUSTRATION
| *1 | NO. 1 ENGINE UNDER COVER | *2 | NO. 2 ENGINE UNDER COVER |
| *3 | NO. 3 ENGINE UNDER COVER | *4 | FRONT LOWER BUMPER ABSORBER |
| *5 | FRONT FENDER APRON SEAL LH | *6 | FRONT FENDER APRON SEAL RH |
| *7 | FRONT FLOOR COVER LH | *8 | FRONT WHEEL OPENING EXTENSION PAD LH |
| *9 | FRONT WHEEL OPENING EXTENSION PAD RH | - | - |
ILLUSTRATION
| *1 | COOL AIR INTAKE DUCT SEAL | *2 | INLET AIR CLEANER ASSEMBLY |
| *3 | AIR CLEANER CAP WITH AIR CLEANER HOSE | *4 | AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY |
| *5 | AIR CLEANER CASE SUB-ASSEMBLY | *6 | AIR CLEANER BRACKET |
| *7 | V-BANK COVER SUB-ASSEMBLY | *8 | ECM |
| *9 | NO. 1 FUEL VAPOR FEED HOSE | - | - |
 |
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
ILLUSTRATION
| *A | for LHD | *B | for RHD |
| *C | for 2WD | *D | for AWD |
| *1 | TRANSMISSION CONTROL CABLE ASSEMBLY | *2 | FUEL VAPOR FEED HOSE ASSEMBLY |
| *3 | NO. 1 FUEL HOSE | *4 | NO. 1 RADIATOR HOSE |
| *5 | NO. 2 RADIATOR HOSE | *6 | INLET HEATER WATER HOSE |
| *7 | OUTLET HEATER WATER HOSE | *8 | UNION TO CHECK VALVE HOSE |
| *9 | NO. 1 TRANSMISSION OIL COOLER HOSE ASSEMBLY | *10 | DISCHARGE HOSE SUB-ASSEMBLY |
| *11 | SUCTION HOSE SUB-ASSEMBLY | *12 | NO. 2 EARTH WIRE |
| *13 | NO. 2 FUEL PIPE CLAMP | *14 | NO. 2 FUEL TUBE SUB-ASSEMBLY |
| *15 | FUEL TUBE SUB-ASSEMBLY | *16 | O-RING |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
 |
for HFC-134a (R134a): Compressor oil ND-OIL 8 or equivalent for HFO-1234yf (R1234yf): Compressor oil ND-OIL 12 or equivalent |
- | - |
ILLUSTRATION
| *1 | FRONT STABILIZER BAR | *2 | STEERING LINK ASSEMBLY |
| *3 | STEERING INTERMEDIATE SHAFT ASSEMBLY | *4 | FRONT NO. 1 STABILIZER BRACKET LH |
| *5 | FRONT NO. 1 STABILIZER BRACKET RH | *6 | FRONT NO. 2 STABILIZER BRACKET LH |
| *7 | FRONT NO. 2 STABILIZER BRACKET RH | - | - |
 |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) | |
N*m (kgf*cm, ft.*lbf): Specified torque |
ILLUSTRATION
| *1 | ENGINE WIRE | *2 | FRONT ENGINE MOUNTING INSULATOR |
| *3 | REAR ENGINE MOUNTING INSULATOR | *4 | ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH |
| *5 | ENGINE MOUNTING SPACER | *6 | ENGINE MOUNTING INSULATOR LH |
| *7 | FRONT FRAME ASSEMBLY | *8 | FRAME SIDE RAIL PLATE SUB-ASSEMBLY LH |
| *9 | FRAME SIDE RAIL PLATE SUB-ASSEMBLY RH | *10 | FRONT SUSPENSION MEMBER BRACKET SUB-ASSEMBLY LH |
| *11 | FRONT SUSPENSION MEMBER BRACKET SUB-ASSEMBLY RH | *12 | HOLE PLUG |
| *13 | NO. 2 ENGINE MOUNTING STAY RH | *14 | NO. 2 VACUUM SWITCHING VALVE ASSEMBLY |
| *15 | VACUUM HOSE | *16 | NO. 1 RELAY BLOCK COVER |
| *17 | ENGINE ASSEMBLY WITH TRANSAXLE | - | - |
| |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) | |
N*m (kgf*cm, ft.*lbf): Specified torque |
ILLUSTRATION
| *A | for AWD | - | - |
| *1 | DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT | *2 | NO. 1 CRANKSHAFT POSITION SENSOR PLATE |
| *3 | DRIVE PLATE AND RING GEAR SUB-ASSEMBLY | *4 | REAR DRIVE PLATE SPACER |
| *5 | FLYWHEEL HOUSING UNDER COVER | *6 | STARTER ASSEMBLY |
| *7 | TRANSFER STIFFENER PLATE RH | *8 | FRONT ENGINE MOUNTING BRACKET |
| *9 | AUTOMATIC TRANSAXLE ASSEMBLY | - | - |
| *a | BLACK COLOR: x 1 SILVER COLOR: x 5 |
- | - |
| |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) | |
N*m (kgf*cm, ft.*lbf): Specified torque |
| |
Adhesive 1324 | ★ | Precoated part |