MONOLITHIC CONVERTER COMPONENTS
ILLUSTRATION
| *A | for LHD | - | - |
| *1 | COWL BODY MOUNTING REINFORCEMENT LH | *2 | COWL BODY MOUNTING REINFORCEMENT RH |
| *3 | NO. 1 HEATER AIR DUCT SPLASH SHIELD SEAL | *4 | OUTER COWL TOP PANEL SUB-ASSEMBLY |
| *5 | WATER GUARD PLATE LH | - | - |
 |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) |  |
N*m (kgf*cm, ft.*lbf): Specified torque |
ILLUSTRATION
| *A | for RHD | - | - |
| *1 | COWL BODY MOUNTING REINFORCEMENT LH | *2 | COWL BODY MOUNTING REINFORCEMENT RH |
| *3 | NO. 1 HEATER AIR DUCT SPLASH SHIELD SEAL | *4 | OUTER COWL TOP PANEL SUB-ASSEMBLY |
| *5 | WATER GUARD PLATE LH | - | - |
| |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) | |
N*m (kgf*cm, ft.*lbf): Specified torque |
ILLUSTRATION
| *1 | AIR CLEANER CAP WITH AIR CLEANER HOSE | *2 | ENGINE WIRE |
| *3 | WIRE HARNESS CLAMP BRACKET | *4 | DASH PANEL HEAT INSULATOR |
| *5 | RADIATOR COVER | *6 | NO. 1 AIR CLEANER INLET |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
ILLUSTRATION
| *A | w/ Differential Pressure Sensor | - | - |
| *1 | AIR TUBE ASSEMBLY | *2 | INLET NO. 1 AIR DUCT SUB-ASSEMBLY |
| *3 | VACUUM REGULATING VALVE ASSEMBLY | *4 | VENTILATION EJECTOR |
| *5 | VENTILATION HOSE | *6 | NO. 4 VENTILATION HOSE |
| *7 | NO. 2 INTERCOOLER WATER HOSE | *8 | NO. 3 INTERCOOLER WATER HOSE |
| *9 | NO. 1 VACUUM TRANSMITTING HOSE ASSEMBLY | *10 | NO. 2 VACUUM TRANSMITTING HOSE ASSEMBLY |
| *11 | NO. 3 VACUUM TRANSMITTING HOSE ASSEMBLY | *12 | NO. 2 VACUUM SWITCHING VALVE BRACKET |
| *13 | NO. 1 ENGINE COVER | *14 | O-RING |
| *15 | VACUUM TANK | *16 | VACUUM TRANSMITTING HOSE |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
ILLUSTRATION
| *A | w/ Cover | - | - |
| *1 | FRONT FLOOR COVER LH | *2 | FRONT FLOOR COVER RH |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
ILLUSTRATION
| *A | for 2WD | - | - |
| *1 | FRONT FLOOR CENTER BRACE | *2 | FRONT EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst) |
| *3 | COMPRESSION SPRING | *4 | EXHAUST PIPE GASKET |
| *5 | FRONT NO. 1 FLOOR HEAT INSULATOR | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
ILLUSTRATION
| *A | for AWD | - | - |
| *1 | FRONT FLOOR CENTER BRACE | *2 | FRONT EXHAUST PIPE ASSEMBLY |
| *3 | NO. 2 CENTER EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst) | *4 | EXHAUST PIPE GASKET |
| *5 | FRONT NO. 1 FLOOR HEAT INSULATOR | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
ILLUSTRATION
| *A | for 2WD | *B | w/ Differential Pressure Sensor |
| *C | w/o Differential Pressure Sensor | - | - |
| *1 | EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY (TWC: Front Catalyst) | *2 | OUTLET TURBINE ELBOW GASKET |
| *3 | NO. 2 TURBO INSULATOR | *4 | DRIVE SHAFT HEAT INSULATOR SUB-ASSEMBLY |
| *5 | MANIFOLD SUPPORT BRACKET | *6 | NO. 1 MANIFOLD CONVERTER INSULATOR |
| *7 | AIR FUEL RATIO SENSOR | *8 | NO. 1 VACUUM PIPE |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | * | For use with SST |
| ● | Non-reusable part | - | - |
ILLUSTRATION
| *A | for AWD | *B | w/ Differential Pressure Sensor |
| *C | w/o Differential Pressure Sensor | - | - |
| *1 | EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY (TWC: Front Catalyst) | *2 | OUTLET TURBINE ELBOW GASKET |
| *3 | NO. 2 TURBO INSULATOR | *4 | NO. 1 MANIFOLD CONVERTER INSULATOR |
| *5 | NO. 2 MANIFOLD CONVERTER INSULATOR | *6 | MANIFOLD SUPPORT BRACKET |
| *7 | AIR FUEL RATIO SENSOR | *8 | PROPELLER SHAFT HEAT INSULATOR |
| *9 | PROPELLER SHAFT HEAT INSULATOR BRACKET SUB-ASSEMBLY | *10 | NO. 1 VACUUM PIPE |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | * | For use with SST |
| ● | Non-reusable part | - | - |