MANUAL TRANSAXLE UNIT COMPONENTS
ILLUSTRATION
*1 |
BACK-UP LIGHT SWITCH ASSEMBLY |
*2 |
BREATHER PLUG |
*3 |
BREATHER PROTECTOR |
*4 |
CLUTCH RELEASE BEARING ASSEMBLY |
*5 |
CLUTCH RELEASE FORK BOOT |
*6 |
CLUTCH RELEASE FORK SUB-ASSEMBLY |
*7 |
DRAIN (MTM) PLUG SUB-ASSEMBLY |
*8 |
MANUAL TRANSMISSION FILLER PLUG |
*9 |
SPEEDOMETER DRIVEN HOLE COVER SUB-ASSEMBLY |
*10 |
MANUAL TRANSAXLE ASSEMBLY |
*11 |
O-RING |
*12 |
DRAIN PLUG (MTM) GASKET |
 |
N*m (kgf*cm, ft.*lbf): Specified torque |
● |
Non-reusable part |
 |
Release hub grease |
 |
Adhesive 1344 |
 |
Clutch spline grease |
★ |
Precoated part |
ILLUSTRATION
*1 |
MANUAL TRANSMISSION CASE |
*2 |
NO. 1 GEAR SHIFT FORK |
*3 |
NO. 2 GEAR SHIFT FORK |
*4 |
NO. 2 SHIFT FORK |
*5 |
NO. 3 GEAR SHIFT FORK |
*6 |
SHIFT AND SELECT LEVER SHAFT DUST BOOT |
*7 |
SHIFT AND SELECT LEVER SHAFT SPRING |
*8 |
SHIFT AND SELECT LEVER SUB-ASSEMBLY |
*9 |
SHIFT INTER LOCK PLATE |
*10 |
TRANSAXLE (MTM) CASE SUB-ASSEMBLY |
*11 |
SHIFT FORK SHAFT E RING |
*12 |
NO. 1 REVERSE SHIFT ARM PIN |
*13 |
REVERSE SHIFT ARM |
*14 |
GEAR-BOX CONTROL LEVER SPRING |
*15 |
NO. 3 GEAR SHIFT FORK SHAFT |
*16 |
SHIFT AND SELECT LEVER SHAFT STRAIGHT PIN |
*17 |
PIN |
*18 |
SHIFT AND SELECT LEVER |
*19 |
SHIFT AND SELECT ARM |
*20 |
NO. 2 GEAR SHIFT FORK SHAFT |
*21 |
NO. 3 SHIFT FORK |
- |
- |
● |
Non-reusable part |
|
Lithium soap base glycol grease |
ILLUSTRATION
*1 |
5TH DRIVEN GEAR |
*2 |
5TH GEAR |
*3 |
MANUAL TRANSMISSION CASE |
*4 |
MANUAL TRANSMISSION CASE COVER SUB-ASSEMBLY |
*5 |
NO. 3 TRANSMISSION CLUTCH HUB |
*6 |
REAR (MTM) BEARING RETAINER (FOR INPUT SHAFT ASSEMBLY) |
*7 |
REAR (MTM) BEARING RETAINER (FOR OUTPUT SHAFT ASSEMBLY) |
*8 |
NO. 2 SYNCHRONIZER RING SET |
*9 |
NO. 3 TRANSMISSION HUB SLEEVE |
*10 |
SPACER |
*11 |
NO. 3 TRANSMISSION CLUTCH HUB SHAFT SNAP RING |
*12 |
5TH GEAR THRUST WASHER |
*13 |
5TH GEAR SHAFT SNAP RING |
*14 |
MANUAL TRANSMISSION CASE COVER GASKET |
*15 |
SYNCHROMESH SHIFTING KEY BALL |
*16 |
COMPRESSION SPRING |
*17 |
NO. 2 SYNCHROMESH SHIFTING KEY |
*18 |
NO. 3 SYNCHRONIZER HUB ASSEMBLY |
|
N*m (kgf*cm, ft.*lbf): Specified torque |
● |
Non-reusable part |
|
Adhesive 1324 |
★ |
Precoated part |
ILLUSTRATION
*1 |
CLUTCH BUFFER GUIDE BUSH |
*2 |
DIFFERENTIAL CASE ASSEMBLY |
*3 |
FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING (OUTER RACE) |
*4 |
FRONT DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING (OUTER RACE) |
*5 |
FRONT DRIVE SHAFT OIL SEAL LH |
*6 |
FRONT DRIVE SHAFT OIL SEAL RH |
*7 |
MANUAL TRANSMISSION CASE |
*8 |
NO. 1 MANUAL TRANSMISSION CASE STRAIGHT PIN |
*9 |
NO. 1 SHIFT AND SELECT LEVER SHAFT NEEDLE ROLLER BEARING |
*10 |
NO. 2 MANUAL TRANSMISSION CASE STRAIGHT PIN |
*11 |
NO. 2 REVERSE SHIFT ARM PIN |
*12 |
NO. 2 SHIFT AND SELECT LEVER SHAFT NEEDLE ROLLER BEARING |
*13 |
NO. 2 TRANSAXLE (MTM) CASE |
*14 |
REVERSE IDLER GEAR SHAFT |
*15 |
REVERSE IDLER GEAR SUB-ASSEMBLY |
*16 |
REVERSE SHIFT ARM BRACKET |
*17 |
OUTPUT SHAFT ASSEMBLY |
*18 |
INPUT SHAFT ASSEMBLY |
*19 |
SPRING |
*20 |
NO. 1 TRANSAXLE (MTM) CASE |
*21 |
TRANSMISSION MAGNET |
*22 |
RIVET |
|
N*m (kgf*cm, ft.*lbf): Specified torque |
|
MP Grease |
|
Adhesive 1324 |
● |
Non-reusable part |
★ |
Precoated part |
- |
- |