СИСТЕМА АВТОМАТИЧЕСКОЙ ТРАНСМИССИИ С ЭЛЕКТРОННЫМ УПРАВЛЕНИЕМ, Diagnostic DTC:P2716/77

DTC Code DTC Name
P2716/77 Pressure Control Solenoid "D" Electrical (Shift Solenoid Valve SLT)

DESCRIPTION

Shift solenoid valve SLT controls the transmission line pressure for smooth transmission operation based on signals from the throttle position sensor and vehicle speed sensor.

The TCM adjusts the current to shift solenoid valve SLT to control the hydraulic line pressure coming from the primary regulator valve. Appropriate line pressure assures smooth shifting with varying engine outputs.

B007SP8E01
DTC No. DTC Detection Condition Trouble Area
P2716/77 Open or short is detected in shift solenoid valve SLT circuit for 1 second or more while driving (1-trip detection logic).

  • Open or short in shift solenoid valve SLT circuit

  • Shift solenoid valve SLT

  • TCM

MONITOR DESCRIPTION

When an open or short in the shift solenoid valve SLT circuit is detected, the TCM interprets this as a fault.

The TCM will turn on the MIL* and store the DTC.

*: for 1KD-FTV w/o Flex Lock Up, 2KD-FTV

WIRING DIAGRAM

B007VOZE04

INSPECTION PROCEDURE

PROCEDURE


  1. INSPECT TRANSMISSION WIRE (SLT)


    1. B007T7UE03

      Disconnect the transmission wire connector from the transmission.

    2. Measure the resistance according to the value(s) in the table below.

      Resistance
      Tester Connection

      Specified Condition

      20°C (68°F)
      2 (SLT+) - 6 (SLT-) 5.0 to 5.6 Ω

    3. Measure the resistance according to the value(s) in the table below.

      Resistance (Check for short)
      Tester Connection Specified Condition
      2 (SLT+) - Body ground 10 kΩ or higher
      6 (SLT-) - Body ground ↑

    NG

    INSPECT SHIFT SOLENOID VALVE SLT Click here

    OK

  2. CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - TCM)


    1. B007W80E14

      Connect the transmission wire connector to the transmission.

    2. Disconnect the TCM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Resistance
      Tester Connection

      Specified Condition

      20°C (68°F)
      O1-20 (SLT+) - O1-19 (SLT-) 5.0 to 5.6 Ω

    4. Measure the resistance according to the value(s) in the table below.

      Resistance (Check for short)
      Tester Connection Specified Condition
      O1-20 (SLT+) - Body ground 10 kΩ or higher
      O1-19 (SLT-) - Body ground ↑

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

    REPLACE TCM

  3. INSPECT SHIFT SOLENOID VALVE SLT


    1. B007RKVE27

      Remove the shift solenoid valve (SLT).

    2. Measure the resistance according to the value(s) in the table below.

      Resistance
      Tester Connection

      Specified Condition

      20°C (68°F)
      1 - 2 5.0 to 5.6 Ω

    3. Connect the positive (+) lead with a 21 W bulb to terminal 2 and the negative (-) lead to terminal 1 of the solenoid valve connector, then check the movement of the valve.

      OK
      The solenoid makes an operating sound.

    NG

    REPLACE SHIFT SOLENOID VALVE SLT

    OK

    REPAIR OR REPLACE TRANSMISSION WIRE