SHIFT LEVER INSPECTION

PROCEDURE

1. INSPECT SHIFT LEVER ASSEMBLY (w/o Smart Key System)

   1. 

      *a	Component with harness connected (Shift Lever Assembly)

      Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection	Condition	Specified Condition
      1 (ACC) - Body ground	Ignition switch ON	11 to 14 V
      	Ignition switch ACC	11 to 14 V
      	Ignition switch off	Below 1 V
      8 (STP) - Body ground	Brake pedal depressed	11 to 14 V
      	Brake pedal released	Below 1 V
      5 (KLS+) - Body ground	Ignition switch ACC and shift lever in P	Below 1 V
      	Ignition switch ACC and shift lever not in P	11 to 14 V
      4 (IG) - Body - ground	Ignition switch to ON	11 to 14 V
      	Ignition switch off	Below 1 V

      Tip:

      Do not disconnect the shift lever assembly connector.

      If the voltage value is not as specified, replace the shift lever assembly.

   2. 

      *a	Component with harness connected (Shift Lever Assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection	Condition	Specified Condition
      7 (E) - Body ground	Always	Below 1 Ω

      Tip:

      Do not disconnect the shift lever assembly connector.

      If the resistance value is not as specified, replace the shift lever assembly.

2. INSPECT SHIFT LEVER ASSEMBLY (w/ Smart Key System)

   1. 

      *a	Component with harness connected (Shift Lever Assembly)

      Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection	Condition	Specified Condition
      1 (ACC) - Body ground	Engine switch on (IG)	11 to 14 V
      	Engine switch on (ACC)	11 to 14 V
      	Engine switch off	Below 1 V
      8 (STP) - Body ground	Brake pedal depressed	11 to 14 V
      	Brake pedal released	Below 1 V
      2 (P2) - Body ground	Engine switch on (ACC) and shift lever not in P	Below 1 V
      	Engine switch on (ACC) and shift lever in P	11 to 14 V
      4 (IG) - Body - ground	Engine switch on (IG)	11 to 14 V
      	Engine switch off	Below 1 V

      Tip:

      Do not disconnect the shift lever assembly connector.

      If the voltage value is not as specified, replace the shift lever assembly.

   2. 

      *a	Component with harness connected (Shift Lever Assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection	Condition	Specified Condition
      7 (E) - Body ground	Always	Below 1 Ω

      Tip:

      Do not disconnect the shift lever assembly connector.

      If the resistance value is not as specified, replace the shift lever assembly.

3. INSPECT TRANSMISSION CONTROL SWITCH

   1. Disconnect the connector from the shift lever assembly.

   2. 

      *A	for LHD
      *a	Component with harness connected (Transmission control switch)

      for LHD:

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection	Condition	Specified Condition
      4 (IG) - 5 (S)	Shift lever in M, "+" or "-"	Below 1 Ω
      3 (SFTU) - 2 (E)	Shift lever held in "+" (Up-shift)	Below 1 Ω
      1 (SFTD) - 2 (E)	Shift lever held in "-" (Down-shift)	Below 1 Ω
      4 (IG) - 5 (S)	Shift lever not in M, "+" or "-"	10 kΩ or higher
      3 (SFTU) - 2 (E)	Shift lever in M	10 kΩ or higher
      1 (SFTD) - 2 (E)	Shift lever in M	10 kΩ or higher

      If the resistance value is not as specified, replace the shift lever assembly.

   3. 

      *A	for RHD
      *a	Component with harness connected (Transmission control switch)

      for RHD:

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection	Condition	Specified Condition
      4 (IG) - 5 (S)	Shift lever in M, "+" or "-"	Below 1 Ω
      1 (SFTU) - 2 (E)	Shift lever held in "+" (Up-shift)	Below 1 Ω
      3 (SFTD) - 2 (E)	Shift lever held in "-" (Down-shift)	Below 1 Ω
      4 (IG) - 5 (S)	Shift lever not in M, "+" or "-"	10 kΩ or higher
      1 (SFTU) - 2 (E)	Shift lever in M	10 kΩ or higher
      3 (SFTD) - 2 (E)	Shift lever in M	10 kΩ or higher

      If the resistance value is not as specified, replace the shift lever assembly.