INTELLIGENT PARKING ASSIST SYSTEM, Diagnostic DTC:C1627

DTC Code DTC Name
C1627 Vehicle Height Sensor Voltage is Low or High

DESCRIPTION

The rear height control sensor sub-assembly RH and headlight leveling ECU assembly (for LED headlight) are connected to the parking assist ECU. The parking assist ECU shares the vehicle height signals received from the rear height control sensor sub-assembly RH with the lighting system (auto leveling). The headlight leveling ECU assembly (for LED headlight) supplies power to the rear height control sensor sub-assembly RH via the parking assist ECU. This DTC is stored when the parking assist ECU judges that the power supply voltage for the rear height control sensor sub-assembly RH is not normal.

DTC No. DTC Detection Condition Trouble Area
C1627

  • Height control sensor voltage is low

  • Height control sensor voltage is high

  • Harness or connector

  • Headlight leveling ECU assembly (for LED Headlight)

  • Parking assist ECU

WIRING DIAGRAM


  1. for LED Headlight

    A005BDVE05

  2. for Halogen Headlight

    A005EBIE04
    *a HBE+
    *b Rear Height Control Sensor Sub-assembly RH
    *c Parking Assist ECU

CAUTION / NOTICE / HINT

Note


  • When the "System initializing" message is displayed on the navigation ECU sub-assembly after the auxiliary battery cable has been disconnected, correct the steering angle neutral point Click here.

  • Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the intelligent parking assist system may be needed Click here.

  • When the headlight leveling ECU assembly (for LED headlight) is replaced, perform initialization for the lighting system Click here

  • If initialization is necessary while performing an inspection, perform initialization first and then proceed to the next step.

PROCEDURE


  1. CHECK DTC OUTPUT


    1. Clear the DTCs Click here.

    2. Check for DTCs Click here.

      Result
      Result Proceed to
      DTC C1627 is output A
      DTCs are not output B

      Tech Tips


      • If the power source voltage output by the headlight leveling ECU assembly (for LED headlight) is abnormal, the headlight leveling warning light may come on.

      • If the DTCs are not output again when rechecking for DTCs, it may have been stored due to a temporarily abnormal voltage.

      • If DTC C1627 is output frequently, duplicate the problem symptoms and perform the inspection again, even though the DTCs are not output when rechecking for DTCs Click here.


    B

    USE SIMULATION METHOD TO CHECK Click here

    A

  2. CHECK VEHICLE SPECIFICATION


    1. Check vehicle specifications.

      Result
      Result Proceed to
      for LED Headlight A
      for Halogen Headlight B

    B

    CHECK HARNESS AND CONNECTOR (REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY RH - PARKING ASSIST ECU) Click here

    A

  3. CHECK HARNESS AND CONNECTOR (HEADLIGHT LEVELING ECU ASSEMBLY - PARKING ASSIST ECU)


    1. Disconnect the A48 headlight leveling ECU assembly connector.

    2. Disconnect the L65 parking assist ECU connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      A48-12 (SBR) - Body ground Always 10 kΩ or higher
      A48-21 (SGR) - Body ground Always 10 kΩ or higher
      A48-12 (SBR) - L65-28 (HB+) Always Below 1 Ω
      A48-21 (SGR) - L65-29 (HGND) Always Below 1 Ω

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  4. CHECK HEADLIGHT LEVELING ECU ASSEMBLY


    1. Reconnect the A48 headlight leveling ECU assembly connector.

    2. Disconnect the L65 parking assist ECU connector.

    3. A005DKIE01
      Text in Illustration
      *a

      Front view of wire harness connector

      (to Parking Assist ECU)

      Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      L65-28 (HB+) - L65-29 (HGND) Power switch on (IG) 4.75 to 5.25 V

    NG

    REPLACE HEADLIGHT LEVELING ECU ASSEMBLY Click here

    OK

  5. CHECK HARNESS AND CONNECTOR (REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY RH - PARKING ASSIST ECU)


    1. Disconnect the L65 parking assist ECU connector.

    2. Disconnect the S25 rear height control sensor sub-assembly RH connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      L65-27 (HBL+) - Body ground Always 10 kΩ or higher
      L65-31 (HG1) - Body ground Always 10 kΩ or higher
      L65-27 (HBL+) - S25-3 (SHB) Always Below 1 Ω
      L65-31 (HG1) - S25-1 (SHG) Always Below 1 Ω
      Result
      Result Proceed to
      NG A
      OK B

    A

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    B

    CHECK REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY RH Click here

  6. CHECK HARNESS AND CONNECTOR (REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY RH - PARKING ASSIST ECU)


    1. Disconnect the L65 parking assist ECU connector.

    2. Disconnect the S25 rear height control sensor sub-assembly RH connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      L65-30 (HBE+) - Body ground Always 10 kΩ or higher
      L65-31 (HG1) - Body ground Always 10 kΩ or higher
      L65-30 (HBE+) - S25-3 (SHB) Always Below 1 Ω
      L65-31 (HG1) - S25-1 (SHG) Always Below 1 Ω

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  7. CHECK REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY RH


    1. Reconnect the L65 parking assist ECU connector.

    2. Disconnect the S25 rear height control sensor sub-assembly RH connector.

    3. A005A1ZE02
      Text in Illustration
      *a

      Front view of wire harness connector

      (to Rear Height Control Sensor Sub-assembly RH)

      Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      S25-3 (SHB) - S25-1 (SHG) Power switch on (IG) 4.75 to 5.25 V

    OK

    REPLACE REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY RH Click here

    NG

    REPLACE PARKING ASSIST ECU Click here