POWER WINDOW CONTROL SYSTEM Front Passenger Side Power Window does not Operate with Front Passenger Side Power Window Switch

DTC Code DTC Name
Front Passenger Side Power Window does not Operate with Front Passenger Side Power Window Switch

DESCRIPTION

When the power switch on (IG), the front power window regulator motor assembly RH (for LHD) or front power window regulator motor assembly LH (for RHD) is operated by the power window regulator switch assembly.

WIRING DIAGRAM

B341196E04

CAUTION / NOTICE / HINT

Note:

  • Inspect the fuses for circuits related to this system before performing the following procedure.

  • Check that the window lock switch is off before performing the following procedure.

PROCEDURE

  1. INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY

    1. Remove the power window regulator switch assembly.

      Click here

    2. Inspect the power window regulator switch assembly.

      Click here

    Result

    Proceed to

    OK (for LHD)

    OK (for RHD)

    NG
    OK (for RHD)

    INSPECT FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LHClick here

    NG

    REPLACE POWER WINDOW REGULATOR SWITCH ASSEMBLY

    Click here

    OK (for LHD)

  2. INSPECT FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

    1. Remove the front power window regulator motor assembly RH.

      Click here

    2. Inspect the front power window regulator motor assembly RH.

      Click here

    Result

    Proceed to

    OK

    NG
    NG

    REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

    Click here

    OK

  3. CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH ASSEMBLY - AUXILIARY BATTERY)

    1. B276367C01

      *a

      Front view of wire harness connector

      (to Power Window Regulator Switch Assembly)

      Disconnect the power window regulator switch assembly connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection

      Switch Condition

      Specified Condition

      I4-3 (B) - Body ground

      Power switch on (IG)

      11 to 14 V

      Power switch off

      Below 1 V

    Result

    Proceed to

    OK

    NG
    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  4. CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH)

    1. Disconnect the I4 power window regulator switch assembly connector.

    2. Disconnect the I2 front power window regulator motor assembly RH connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      I4-4 (U) - I2-2 (U)

      Always

      Below 1 Ω

      I4-1 (D) - I2-1 (D)

      Always

      Below 1 Ω

      I4-4 (U) or I2-2 (U) - Body ground

      Always

      10 kΩ or higher

      I4-1 (D) or I2-1 (D) - Body ground

      Always

      10 kΩ or higher

    Result

    Proceed to

    OK

    NG
    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  5. CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - POWER WINDOW REGULATOR SWITCH ASSEMBLY)

    1. Disconnect the J5 power window regulator master switch assembly connector.

    2. Disconnect the I4 power window regulator switch assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      J5-16 (U) - I4-5 (SU)

      Always

      Below 1 Ω

      J5-15 (D) - I4-2 (SD)

      Always

      Below 1 Ω

      J5-16 (U) or I4-5 (SU) - Body ground

      Always

      10 kΩ or higher

      J5-15 (D) or I4-2 (SD) - Body ground

      Always

      10 kΩ or higher

    Result

    Proceed to

    OK

    NG
    OK

    REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

    Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  6. INSPECT FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

    1. Remove the front power window regulator motor assembly LH.

      Click here

    2. Inspect the front power window regulator motor assembly LH.

      Click here

    Result

    Proceed to

    OK

    NG
    NG

    REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

    Click here

    OK

  7. CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH ASSEMBLY - AUXILIARY BATTERY)

    1. B276367C04

      *a

      Front view of wire harness connector

      (to Power Window Regulator Switch Assembly)

      Disconnect the power window regulator switch assembly connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection

      Switch Condition

      Specified Condition

      J4-3 (B) - Body ground

      Power switch on (IG)

      11 to 14 V

      Power switch off

      Below 1 V

    Result

    Proceed to

    OK

    NG
    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  8. CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH)

    1. Disconnect the J4 power window regulator switch assembly connector.

    2. Disconnect the J2 front power window regulator motor assembly LH connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      J4-4 (U) - J2-2 (U)

      Always

      Below 1 Ω

      J4-1 (D) - J2-1 (D)

      Always

      Below 1 Ω

      J4-4 (U) or J2-2 (U) - Body ground

      Always

      10 kΩ or higher

      J4-1 (D) or J2-1 (D) - Body ground

      Always

      10 kΩ or higher

    Result

    Proceed to

    OK

    NG
    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  9. CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - POWER WINDOW REGULATOR SWITCH ASSEMBLY)

    1. Disconnect the I5 power window regulator master switch assembly connector.

    2. Disconnect the J4 power window regulator switch assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      I5-12 (U) - J4-5 (SU)

      Always

      Below 1 Ω

      I5-13 (D) - J4-2 (SD)

      Always

      Below 1 Ω

      I5-12 (U) or J4-5 (SU) - Body ground

      Always

      10 kΩ or higher

      I5-13 (D) or J4-2 (SD) - Body ground

      Always

      10 kΩ or higher

    Result

    Proceed to

    OK

    NG
    OK

    REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

    Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR