LIGHTING SYSTEM DATA LIST / ACTIVE TEST


  1. DATA LIST

    Tech Tips

    Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

    Note

    In the following table, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Main Body / Data List.

    5. Read the Data List according to the display on the GTS.

      Main Body
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      ACC SW Power switch ACC signal/ON or OFF

      ON: Power switch on (ACC)

      OFF: Power switch off

      		 -
      IG SW Power switch IG signal/ON or OFF

      ON: Power switch on (IG)

      OFF: Power switch off

      		 -
      RR Door Courtesy SW Rear door courtesy light switch RH signal/ON or OFF

      ON: Rear door LH open and rear door RH closed

      ON: Rear door LH closed and rear door RH open

      ON: Rear door LH and rear door RH open

      OFF: Rear door LH and rear door RH closed

      		 -
      RL Door Courtesy SW Rear door courtesy light switch LH signal/ON or OFF

      ON: Rear door LH open and rear door RH closed

      ON: Rear door LH closed and rear door RH open

      ON: Rear door LH and rear door RH open

      OFF: Rear door LH and rear door RH closed

      		 -
      Back Door Courtesy SW Back door courtesy switch signal/ON or OFF

      ON: Back door open

      OFF: Back door closed

      		 -
      FR Door Lock Pos Front door unlock detection switch RH signal/ON or OFF

      ON: Front door RH unlocked

      OFF: Front door RH locked

      		 -
      FR Door Courtesy SW Front door courtesy light switch RH signal/ON or OFF

      ON: Front door RH open

      OFF: Front door RH closed

      		 -
      FL Door Lock Pos Front door unlock detection switch LH signal/ON or OFF

      ON: Front door LH unlocked

      OFF: Front door LH locked

      		 -
      FL Door Courtesy SW Front door courtesy light switch LH signal/ON or OFF

      ON: Front door LH open

      OFF: Front door LH closed

      		 -
      RR-Door Lock Pos SW Rear door unlock detection switch RH signal/ON or OFF

      ON: Rear door LH locked and rear door RH unlocked

      ON: Rear door LH unlocked and rear door RH locked

      ON: Rear door LH and rear door RH unlocked

      OFF: Rear door LH and rear door RH locked

      		 -
      RL-Door Lock Pos SW Rear door unlock detection switch LH signal/ON or OFF

      ON: Rear door LH locked and rear door RH unlocked

      ON: Rear door LH unlocked and rear door RH locked

      ON: Rear door LH and rear door RH unlocked

      OFF: Rear door LH and rear door RH locked

      		 -
      Interior Light Control Operation of the illuminated entry system/OFF or ON

      OFF: System not operated

      ON: System operated

      		 Customized value is displayed
      I/L ON W/Door Key Unlock Function that lights up the interior lights when the doors are unlocked/OFF or ON

      OFF: Function disabled

      ON: Function enabled

      		 Customized value is displayed
      Lighting Time Lighting time of the delay control function (illuminated entry system)/15s, 7.5s or 30s

      15s: 15 seconds

      7.5s: 7.5 seconds

      30s: 30 seconds

      		 Customized value is displayed
      Room Light when Aprchd Function that lights up the interior lights when a key enters any actuation area/OFF or ON

      OFF: Function disabled

      ON: Function enabled

      		 Customized value is displayed
      Inside Foot Light Function that lights up the footwell lights (Always) /OFF or ON

      OFF: Function disabled

      ON: Function enabled

      		 Customized value is displayed
      I/L when ACC OFF Function that lights up the interior lights when the power switch is turned from on (IG) or on (ACC) to off/OFF or ON

      OFF: Function disabled

      ON: Function enabled

      		 Customized value is displayed
      Light Control Function that lights up the footwell lights (while Driving) /OFF or ON

      OFF: Function disabled

      ON: Function enabled

      		 Customized value is displayed

  2. ACTIVE TEST

    Tech Tips

    Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / (desired system) / Active Test.

    5. Perform the Active Test according to the display on the GTS.

      Main Body
      Tester Display Test Part Control Range Diagnostic Note
      Illuminated Entry System Interior lights ON/OFF Interior light door switch DOOR and all doors closed
      Fr Foot Light Footwell lights ON/OFF

      Precondition for using the Active Test to turn lights on and off:


      • Power switch is turned off just before performing the Active Test.

      Preconditions for using the Active Test to check dimmer controlled illumination:


      • Power switch is on (READY).

      • A shift state other than park (P) has been selected.
      Entry&Start
      Tester Display Test Part Control Range Diagnostic Note
      Power/Engine SW Light Power switch light ON/OFF

      When performing this Active Test, make sure the following condition is met:

      The power switch illumination is off (15 seconds or more have elapsed since it turned from on to off) and the power switch is on (ACC) or on (IG), or the hybrid control system is running.