SFI SYSTEM(w/ Canister Pump Module), Diagnostic DTC:P2195 and P2196

DTC Code DTC Name
P2195 Oxygen (A/F) Sensor Signal Stuck Lean (Bank 1 Sensor 1)
P2196 Oxygen (A/F) Sensor Signal Stuck Rich (Bank 1 Sensor 1)

DESCRIPTION

Tip:

  • Although the DTC titles say oxygen sensor, these DTCs relate to the air fuel ratio sensor.

  • Sensor 1 refers to the sensor mounted in front of the three-way catalytic converter and located near the engine assembly.

The air fuel ratio sensor generates a voltage* that corresponds to the actual air fuel ratio. This sensor voltage is used to provide the ECM with feedback so that it can control the air fuel ratio. The ECM determines the deviation from the stoichiometric air fuel ratio level, and regulates the fuel injection duration. If the air fuel ratio sensor malfunctions, the ECM is unable to control the air fuel ratio accurately.

The air fuel ratio sensor is a planar type and is integrated with the heater, which heats the solid electrolyte (zirconia element). This heater is controlled by the ECM. When the intake air volume is low (the exhaust gas temperature is low), a current flows into the heater to heat the sensor, in order to facilitate accurate oxygen concentration detection. In addition, the sensor and heater portions are a narrow type. The heat generated by the heater is conducted to the solid electrolyte through the alumina, and therefore sensor activation is accelerated.

In order to obtain a high purification rate of the carbon monoxide (CO), hydrocarbon (HC) and nitrogen oxide (NOx) components in the exhaust gas, a three-way catalytic converter is used. For the most efficient use of the three-way catalytic converter, the air fuel ratio must be precisely controlled so that it is always close to the stoichiometric level.

*: Value changes inside the ECM. Since the air fuel ratio sensor is a current output element, the current is converted into a voltage inside the ECM. Any measurements taken at the air fuel ratio sensor or ECM connectors will show a constant voltage.

A234900E19

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

MIL

Memory

P2195

Oxygen (A/F) Sensor Signal Stuck Lean (Bank 1 Sensor 1)

Either of the following conditions (A) or (B) met:

  • (A)

  • Conditions (a) and (b) continue for 5 seconds or more (2 trip detection logic):

    1. Air fuel ratio sensor voltage is higher than 3.8 V.

    2. Heated oxygen sensor voltage is 0.21 V or higher.

  • (B)

  • While the fuel-cut operation is performed (during vehicle deceleration), the air fuel ratio sensor current is 2.2 mA or higher for 3 seconds (2 trip detection logic).

  • Open or short in air fuel ratio sensor (sensor 1) circuit

  • Air fuel ratio sensor (sensor 1)

  • Intake system

  • Fuel pressure

  • Fuel injector assembly

  • ECM

Comes on

DTC stored

P2196

Oxygen (A/F) Sensor Signal Stuck Rich (Bank 1 Sensor 1)

Either of the following conditions (A) or (B) is met:

  • (A)

  • Conditions (a) and (b) continue for 5 seconds or more (2 trip detection logic):

    1. Air fuel ratio sensor voltage is less than 2.8 V.

    2. Heated oxygen sensor voltage is less than 0.69 V.

  • (B)

  • While the fuel-cut operation is performed (during vehicle deceleration), the air fuel ratio sensor current is less than 0.7 mA for 3 seconds (2 trip detection logic).

  • Open or short in air fuel ratio sensor (sensor 1) circuit

  • Air fuel ratio sensor (sensor 1)

  • Intake system

  • Fuel pressure

  • Fuel injector assembly

  • ECM

Comes on

DTC stored
Tip:

  • When any of these DTCs is stored, check the air fuel ratio sensor voltage output by entering the following menus on the GTS: Powertrain / Engine and ECT / Data List / Ptrl AF Control / AFS Voltage B1S1.

  • Short-term fuel trim values can also be read using the GTS.

  • The ECM regulates the voltages at the A1A+ and A1A- terminals of the ECM to a constant level. Therefore, the air fuel ratio sensor voltage output cannot be confirmed without using the GTS.

  • If an air fuel ratio sensor malfunction is detected, the ECM stores a DTC.

MONITOR DESCRIPTION

Sensor Voltage Detection Monitor

Under air fuel ratio feedback control, If the air fuel ratio sensor output voltage is below 2.8 V (very rich condition) for 5 seconds despite the heated oxygen sensor output voltage being below 0.69 V, the ECM stores DTC P2196. Alternatively, if the air fuel ratio sensor output voltage is higher than 3.8 V (very lean condition) for 5 seconds despite the heated oxygen sensor output voltage being 0.21 V or higher, DTC P2195 is stored.

Sensor Current Detection Monitor

A rich air fuel mixture causes a low air fuel ratio sensor current, and a lean air fuel mixture causes a high air fuel ratio sensor current. Therefore, the sensor output becomes low during acceleration, and it becomes high during deceleration with the throttle valve fully closed. The ECM monitors the air fuel ratio sensor current during fuel-cut and detects any abnormal current values.

If the air fuel ratio sensor output is 2.2 mA or higher for more than 3 seconds of cumulative time, the ECM interprets this as a malfunction in the air fuel ratio sensor and stores DTC P2195 (stuck on high side). If the air fuel ratio sensor output is below 0.7 mA for more than 3 seconds of cumulative time, the ECM stores DTC P2196 (stuck on low side).

A293209E02

MONITOR STRATEGY

Required Sensors/Components (Main)

Air fuel ratio sensor

Required Sensors/Components (Related)

Heated oxygen sensor

Frequency of Operation

Continuous: Sensor voltage detection monitor

Once per driving cycle: Sensor current detection monitor

Duration

5 seconds: Sensor voltage detection monitor

3 seconds: Sensor current detection monitor

TYPICAL ENABLING CONDITIONS

Table 1. P2195 and P2196: Sensor Voltage Detection Monitor

Time after engine start

30 seconds or more

Fuel system status

Closed loop
Table 2. P2195 and P2196: Sensor Current Detection Monitor

Battery voltage

11 V or higher

Atmospheric pressure

76 kPa(abs) [570 mmHg(abs)] or higher

Air fuel ratio sensor status

Activated

Engine coolant temperature

75°C (167°F) or higher

Continuous time of fuel cut

3 seconds or more, and less than 10 seconds

TYPICAL MALFUNCTION THRESHOLDS

Table 3. P2195: Sensor Voltage Detection Monitor (Lean Side Malfunction)

Heated oxygen sensor voltage

0.21 V or higher

Air fuel ratio sensor voltage

Higher than 3.8 V
Table 4. P2196: Sensor Voltage Detection Monitor (Rich Side Malfunction)

Heated oxygen sensor voltage

Less than 0.69 V

Air fuel ratio sensor voltage

Less than 2.8 V
Table 5. P2195: Sensor Current Detection Monitor (High Side Malfunction)

Air fuel ratio sensor current

2.2 mA or higher
Table 6. P2196: Sensor Current Detection Monitor (Low Side Malfunction)

Air fuel ratio sensor current

Less than 0.7 mA

CONFIRMATION DRIVING PATTERN

A293210E02
A268801E05

  1. Connect the GTS to the DLC3.

  2. Turn the engine switch on (IG).

  3. Turn the GTS on.

  4. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

  5. Turn the engine switch off and wait for at least 30 seconds.

  6. Turn the engine switch on (IG) and turn the GTS on.

  7. Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [A].

  8. On the GTS, enter the following menus to check the fuel-cut status: Powertrain / Engine and ECT / Data List / Primary / Idle Fuel Cut.

  9. Drive the vehicle at a speed between 60 and 120 km/h (37 and 75 mph) for at least 10 minutes [B].

    CAUTION:

    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

  10. With the shift lever in S position [C], accelerate the vehicle to 64 km/h (40 mph) or more by depressing the accelerator pedal for at least 10 seconds [D].

    CAUTION:

    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

  11. Soon after performing step [D] above, release the accelerator pedal for at least 4 seconds without depressing the brake pedal in order to execute fuel-cut control [E].

    Tip:

    Fuel-cut is performed when the following conditions are met:

    • Accelerator pedal is fully released.

    • Engine speed is 1400 rpm or higher (fuel injection restart rpm).

  12. Allow the vehicle to decelerate until the vehicle speed decreases to less than 10 km/h (6 mph).

  13. Repeat steps [C] through [E] above at least 3 times in one driving cycle.

  14. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [F].

  15. Read the pending DTCs.

    Tip:

    • If a pending DTC is output, the system is malfunctioning.

    • If a pending DTC is not output, perform the following procedure.

  16. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

  17. Input the DTC: P2195 or P2196.

  18. Check the DTC judgment result.

    GTS Display

    Description

    NORMAL

    • DTC judgment completed

    • System normal

    ABNORMAL

    • DTC judgment completed

    • System abnormal

    INCOMPLETE

    • DTC judgment not completed

    • Perform driving pattern after confirming DTC enabling conditions

    N/A

    • Unable to perform DTC judgment

    • Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit
    Tip:

    • If the judgment result shows NORMAL, the system is normal.

    • If the judgment result shows ABNORMAL, the system has a malfunction.

    • If the judgment result shows INCOMPLETE or N/A, perform steps [B] through [F] again.

WIRING DIAGRAM

Refer to DTC P0031.

Click here

CAUTION / NOTICE / HINT

Note:

Inspect the fuses for circuits related to this system before performing the following procedure.

Tip:

  • Sensor 1 refers to the sensor closest to the engine assembly.

  • Sensor 2 refers to the sensor farthest away from the engine assembly.

  • Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

  • A low air fuel ratio sensor voltage could be caused by a rich air fuel mixture. Check for conditions that would cause the engine to run rich.

  • A high air fuel ratio sensor voltage could be caused by a lean air fuel mixture. Check for conditions that would cause the engine to run lean.

PROCEDURE

  1. CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P2195 OR P2196)

    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

    5. Read the DTCs.

      Powertrain > Engine and ECT > Trouble Codes

    Result

    Result

    Proceed to

    DTC P2195 or P2196 is output

    A

    DTC P2195 or P2196 and P0136, P0137 or P0138 are output

    DTC P2195 or P2196 and other DTCs are output

    B
    Tip:

    If any DTCs relating to the air fuel ratio sensor (DTCs for the air fuel ratio sensor heater or air fuel ratio sensor admittance) are output, troubleshoot those DTCs first.

    B

    GO TO DTC CHART

    Click here

    A

  2. CONFIRM IF VEHICLE HAS RUN OUT OF FUEL IN PAST

    1. Has the vehicle run out of fuel in the past?

    Result

    Proceed to

    YES

    NO
    NO

    READ VALUE USING GTS (TEST VALUE OF AIR FUEL RATIO SENSOR)Click here

    YES

  3. CHECK WHETHER DTC OUTPUT RECURS (DTC P2195 OR P2196)

    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Clear the DTCs.

      Click here

      Powertrain > Engine and ECT > Clear DTCs

    5. Turn the engine switch off and wait for at least 30 seconds.

    6. Turn the engine switch on (IG).

    7. Turn the GTS on.

    8. Start the engine and warm it up.

    9. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

    10. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

      Powertrain > Engine and ECT > Utility

      Tester Display

      All Readiness

    11. Input the DTC: P2195 or P2196.

    12. Check the DTC judgment.

    Result

    Result

    Proceed to

    NORMAL (DTC is not output)

    A

    ABNORMAL (DTC P2195 or P2196 is output)

    B
    A

    DTC CAUSED BY RUNNING OUT OF FUEL

    B

    READ VALUE USING GTS (TEST VALUE OF AIR FUEL RATIO SENSOR)Click here

  4. READ VALUE USING GTS (TEST VALUE OF AIR FUEL RATIO SENSOR)

    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Clear the DTCs.

      Click here

      Powertrain > Engine and ECT > Clear DTCs

    5. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

    6. Enter the following menus: Powertrain / Engine and ECT / Monitor / Current Monitor / O2 Sensor / Current.

      Powertrain > Engine and ECT > Monitor

    7. Check that the status of O2 Sensor is Complete. If the status is still Incomplete, drive the vehicle according to the driving pattern again.

    8. Enter the following menus: Powertrain / Engine and ECT / Monitor / Current Monitor / O2 Sensor / Details / RANGE B1S1.

      Powertrain > Engine and ECT > Monitor

    9. Check the test value of the air fuel ratio sensor output current during fuel-cut.

    Result

    Result

    Proceed to

    Within normal range (0.7 mA or higher, and lower than 2.2 mA)

    A

    Outside normal range (lower than 0.7 mA, or 2.2 mA or higher)

    B
    B

    REPLACE AIR FUEL RATIO SENSORClick here

    A

  5. READ VALUE USING GTS (OUTPUT VOLTAGE OF AIR FUEL RATIO SENSOR)

    1. Connect the GTS to the DLC3.

    2. Start the engine.

    3. Turn the GTS on.

    4. Warm up the air fuel ratio sensor at an engine speed of 2500 rpm for 90 seconds.

    5. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor / Ptrl AF Control / AFS Voltage B1S1 and O2S B1S2.

      Powertrain > Engine and ECT > Active Test

      Active Test Display

      Control the Injection Volume for A/F Sensor

      Data List Display

      AFS Voltage B1S1

      O2S B1S2

    6. Perform the Control the Injection Volume operation with the engine idling.

    7. Monitor the output voltages of the air fuel ratio and heated oxygen sensors (AFS Voltage B1S1 and O2S B1S2) displayed on the GTS.

      Tip:

      • Change the fuel injection volume within the range of -12.5% to +12.5%.

      • The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.

      • If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.

      GTS Display (Sensor)

      Injection Volume

      Status

      Voltage

      AFS Voltage B1S1

      (Air fuel ratio)

      +12.5%

      Rich

      Below 3.1 V

      AFS Voltage B1S1

      (Air fuel ratio)

      -12.5%

      Lean

      Higher than 3.4 V

      O2S B1S2

      (Heated oxygen)

      +12.5%

      Rich

      Higher than 0.55 V

      O2S B1S2

      (Heated oxygen)

      -12.5%

      Lean

      Below 0.4 V

    Result

    Status of AFS Voltage B1S1

    Status of O2S B1S2

    Air Fuel Ratio Condition and Air Fuel Ratio Sensor Condition

    Proceed to

    Lean

    Lean

    Actual air fuel ratio lean

    A

    Rich

    Rich

    Actual air fuel ratio rich

    Lean

    Lean/Rich

    Air fuel ratio sensor malfunction

    B

    Rich

    Lean/Rich

    Air fuel ratio sensor malfunction

    Lean/Rich

    Lean/Rich

    Normal

    Lean: During the Control the Injection Volume Active Test, the air fuel ratio sensor output voltage (AFS Voltage B1S1) is consistently higher than 3.4 V, and the heated oxygen sensor output voltage (O2S B1S2) is consistently below 0.4 V.

    Rich: During the Control the Injection Volume Active Test, the AFS Voltage B1S1 is consistently below 3.1 V, and the O2S B1S2 is consistently higher than 0.55 V.

    Lean/Rich: During the Control the Injection Volume Active Test, the output voltage of the heated oxygen sensor alternates correctly.

    Tip:

    Refer to "Data List / Active Test" [AFS Voltage B1S1 and O2S B1S2].

    Click here

    B

    REPLACE AIR FUEL RATIO SENSORClick here

    A

  6. CHECK INTAKE SYSTEM

    1. Check the intake system for vacuum leaks.

      Click here

      OK

      No leaks in the intake system.

      Tip:

      Perform "Inspection After Repair" after repairing or replacing the intake system.

      Click here

    Result

    Proceed to

    OK

    NG
    NG

    REPAIR OR REPLACE INTAKE SYSTEM

    OK

  7. CHECK FOR EXHAUST GAS LEAK

    1. Check for exhaust gas leaks.

      OK

      No gas leaks.

      Tip:

      Perform "Inspection After Repair" after repairing or replacing the exhaust system.

      Click here

    Result

    Proceed to

    OK

    NG
    NG

    REPAIR OR REPLACE EXHAUST SYSTEM

    OK

  8. CHECK FUEL PRESSURE

    1. Check the fuel pressure.

      Click here

    Result

    Proceed to

    OK

    NG
    NG

    CHECK FUEL LINEClick here

    OK

  9. INSPECT FUEL INJECTOR ASSEMBLY

    1. Inspect the fuel injector assembly injection (whether fuel volume is high or low, and whether injection pattern is poor).

      Click here

      Tip:

      Perform "Inspection After Repair" after replacing the fuel injector assembly.

      Click here

    Result

    Proceed to

    OK

    NG
    NG

    REPLACE FUEL INJECTOR ASSEMBLY

    Click here

    OK

  10. REPLACE AIR FUEL RATIO SENSOR

    1. Replace the air fuel ratio sensor.

      Click here

      Tip:

      Perform "Inspection After Repair" after replacing the air fuel ratio sensor.

      Click here

    Result

    Proceed to

    NEXT
    NEXT

  11. CHECK WHETHER DTC OUTPUT RECURS (DTC P2195 OR P2196)

    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Clear the DTCs.

      Powertrain > Engine and ECT > Clear DTCs

    5. Turn the engine switch off and wait for at least 30 seconds.

    6. Turn the engine switch on (IG).

    7. Turn the GTS on.

    8. Start the engine and warm it up.

    9. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

    10. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

      Powertrain > Engine and ECT > Utility

      Tester Display

      All Readiness

    11. Input the DTC: P2195 or P2196.

    12. Check the DTC judgment result.

    Result

    Result

    Proceed to

    ABNORMAL (DTC P2195 or P2196 is output)

    A

    NORMAL (DTC is not output)

    B
    B

    END

    A

  12. REPLACE ECM

    1. Replace the ECM.

      Click here

    Result

    Proceed to

    NEXT
    NEXT

  13. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Clear the DTCs.

      Click here

      Powertrain > Engine and ECT > Clear DTCs

    5. Turn the engine switch off and wait for at least 30 seconds.

    6. Turn the engine switch on (IG).

    7. Turn the GTS on.

    8. Start the engine and warm it up.

    9. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

    10. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

      Powertrain > Engine and ECT > Utility

      Tester Display

      All Readiness

    11. Input the DTC: P2195 or P2196.

    12. Check the DTC judgment result.

      Result

      GTS Display

      Description

      NORMAL

      • DTC judgment completed

      • System normal

      ABNORMAL

      • DTC judgment completed

      • System abnormal

      INCOMPLETE

      • DTC judgment not completed

      • Perform driving pattern after confirming DTC enabling conditions

      N/A

      • Unable to perform DTC judgment

      • Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    Result

    Proceed to

    NEXT
    NEXT

    END

  14. CHECK FUEL LINE

    1. Check the fuel lines for leaks or blockage.

      Tip:

      Perform "Inspection After Repair" after replacing the fuel pump.

      Click here

    Result

    Proceed to

    OK

    NG
    OK

    REPLACE FUEL PUMP

    Click here

    NG

    REPAIR OR REPLACE FUEL LINE

  15. REPLACE AIR FUEL RATIO SENSOR

    1. Replace the air fuel ratio sensor.

      Click here

      Tip:

      Perform "Inspection After Repair" after replacing the air fuel ratio sensor.

      Click here

    Result

    Proceed to

    NEXT
    NEXT

  16. CHECK WHETHER DTC OUTPUT RECURS (DTC P2195 OR P2196)

    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Clear the DTCs.

      Click here

      Powertrain > Engine and ECT > Clear DTCs

    5. Turn the engine switch off and wait for at least 30 seconds.

    6. Turn the engine switch on (IG).

    7. Turn the GTS on.

    8. Start the engine and warm it up.

    9. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

    10. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

      Powertrain > Engine and ECT > Utility

      Tester Display

      All Readiness

    11. Input the DTC: P2195 or P2196.

    12. Check the DTC judgment result.

    Result

    Result

    Proceed to

    NORMAL (DTC is not output)

    A

    ABNORMAL (DTC P2195 or P2196 is output)

    B
    A

    END

    B

    REPLACE ECM

    Click here