EGR VALVE INSTALLATION

PROCEDURE


  1. INSTALL WIRE HARNESS CLAMP BRACKET


    1. Install the wire harness clamp bracket with the bolt.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

  2. INSTALL EGR VALVE ASSEMBLY


    1. A005CT5

      Temporarily install a new gasket and EGR valve assembly to the EGR cooler assembly with the 2 nuts.

    2. Install a new gasket and set the EGR valve with cooler assembly in place.

    3. Using an E8 "TORX" socket wrench, install the 4 stud bolts.

      A005AN5E01
      Text in Illustration
      *a Stud Bolt A *b Stud Bolt B
      *c Stud Bolt C - -
      Torque:
      Stud Bolt A and Stud Bolt B
      9.5 N*m  { 97 kgf*cm, 84 in.*lbf }
      Stud Bolt C
      5.0 N*m  { 51 kgf*cm, 44 in.*lbf }

      If a stud bolt is deformed or the threads are damaged, replace it.

    4. Temporarily install the 2 nuts (B), 2 nuts (C) and bolt.

      Tech Tips

      The type B nut and type C nut are non-reusable.

      A005A3VE02
      Text in Illustration
      *A Type A *B Type B
      *C Type C - -
      *a Nut A *b Nut B
      *c Nut C *d Bolt

    5. Tighten the 2 nuts (A).

      Torque:
      21 N*m  { 214 kgf*cm, 15 ft.*lbf }

    6. Tighten the 2 nuts (B) and bolt.

      Torque:
      21 N*m  { 214 kgf*cm, 15 ft.*lbf }

      Note

      Make sure that all installation surfaces of the EGR valve with cooler assembly are in even contact when tightening the bolt and nuts.

    7. Tighten the 2 nuts (C).

      Torque:
      Type A
      21 N*m  { 214 kgf*cm, 15 ft.*lbf }
      Type B
      37 N*m  { 377 kgf*cm, 27 ft.*lbf }
      Type C
      26 N*m  { 265 kgf*cm, 19 ft.*lbf }
    8. A005F1I

      Connect the EGR valve assembly connector and engage the wire harness clamp.

    9. Connect the 4 water hoses to the EGR valve assembly and slide the 4 clips to secure them.

  3. INSTALL EGR PIPE ASSEMBLY


    1. Install 2 new gaskets and EGR pipe assembly with the 4 bolts.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

      Note

      Make sure to tighten the 4 bolts evenly until the flanges of the EGR pipe assembly contact the installation surfaces.

    2. Install the wire harness support with the bolt.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }
    3. A005B7N

      Connect the 2 wire harness clamps.

  4. INSTALL AIR CLEANER CASE

    Click here

  5. INSTALL INLET AIR CLEANER ASSEMBLY

    Click here

  6. INSTALL AIR CLEANER CAP SUB-ASSEMBLY

    Click here

  7. INSTALL NO. 2 CYLINDER HEAD COVER

    Click here

  8. ADD COOLANT (for Engine)

    Click here

  9. INSPECT FOR COOLANT LEAK (for Engine)

    Click here

  10. INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY (for LHD)

    Click here

  11. INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD)

    Click here

  12. INSTALL COWL BODY MOUNTING REINFORCEMENT LH (for LHD)

    Click here

  13. INSTALL COWL BODY MOUNTING REINFORCEMENT RH (for RHD)

    Click here

  14. INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

    Click here