СИСТЕМА ECD ECM Power Source Circuit

DESCRIPTION

When the ignition switch is turned to ON, the battery voltage is applied to terminal IGSW of the ECM. The MREL output signal from ECM causes a current to flow to the coil, closing the contacts of the MAIN relay and supplying power to terminal +B of the ECM.

WIRING DIAGRAM

B003LTTE01

CAUTION / NOTICE / HINT

Note


  • After replacing the ECM, the new ECM needs registration (See page ) and initialization Click here.

  • Inspect the fuses of circuits related to this system before performing the following procedure.

PROCEDURE


  1. INSPECT ECM (+B VOLTAGE)


    1. B003LOKC91
      *a

      Component with harness connected

      (ECM)

      Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      G141-1 (+B) - C115-7 (E1) IG ON 11 to 14 V
      Result
      Proceed to
      OK
      NG

    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

    NG

  2. CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)


    1. Disconnect the ECM connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      C115-7 (E1) - Body ground Always Below 1 Ω

    3. Reconnect the ECM connector.

      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  3. INSPECT ECM (IGSW VOLTAGE)


    1. Turn the ignition switch to ON.

    2. B003LOKC92
      *a

      Component with harness connected

      (ECM)

      Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      G141-9 (IGSW) - C115-7 (E1) Ignition switch ON 11 to 14 V
      Result
      Proceed to
      OK
      NG

    NG

    INSPECT IGNITION SWITCH Click here

    OK

  4. INSPECT ECM (MREL VOLTAGE)


    1. Turn the ignition switch to ON.

    2. B003LOKC93
      *a

      Component with harness connected

      (ECM)

      Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      G141-8 (MREL) - C115-7 (E1) Ignition switch ON 11 to 14 V
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE ECM Click here

    OK

  5. INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (EFI-MAIN NO. 1 RELAY)


    1. Inspect the instrument panel junction block assembly (EFI-MAIN NO. 1 relay).

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE EFI-MAIN NO. 1 RELAY

    OK

  6. CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 1 RELAY - ECM, EFI-MAIN NO. 1 RELAY - BODY GROUND)


    1. Check the harness and connector between the instrument panel junction block (EFI-MAIN NO. 1 relay) and ECM.


      1. Disconnect the instrument panel junction block connector.

      2. Disconnect the ECM connector.

      3. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        2G-5 - G141-1 (+B) Always Below 1 Ω
        2P-9 - G141-8 (MREL) Always Below 1 Ω
        2G-5 or G141-1 (+B) - Body ground Always 10 kΩ or higher
        2P-9 or G141-8 (MREL) - Body ground Always 10 kΩ or higher

      4. Reconnect the ECM connector.

      5. Reconnect the instrument panel junction block connector.

    2. Check the harness and connector between the instrument panel junction block (EFI-MAIN NO. 1 relay) and body ground.


      1. Disconnect the instrument panel junction block connector.

      2. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        2J-5 - Body ground Always Below 1 Ω

      3. Reconnect the instrument panel junction block connector.

      Result
      Proceed to
      OK
      NG

    OK

    REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - MAIN RELAY)

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  7. INSPECT IGNITION SWITCH


    1. Disconnect the ignition switch connector.

    2. B003OAWC18
      *1 Ignition Switch

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      4 (AM2) - 3 (IG2) LOCK 10 kΩ or higher
      4 (AM2) - 3 (IG2) ON Below 1 Ω

    3. Reconnect the ignition switch connector.

      Result
      Proceed to
      OK
      NG

    OK

    REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - IGNITION SWITCH, IGNITION SWITCH - ECM)

    NG

    REPLACE IGNITION SWITCH Click here