THROTTLE BODY INSTALLATION

PROCEDURE


  1. INSTALL THROTTLE BODY GASKET


    1. B0086UUC01
      *a Protrusion

      Install a new throttle body gasket to the intake manifold with the protrusion of the throttle body gasket oriented as shown in the illustration.

  2. INSTALL THROTTLE BODY WITH MOTOR ASSEMBLY

    Tech Tips

    Perform "Inspection After Repair" after replacing the throttle body with motor assembly.

    Click here


    1. Install the throttle body with motor assembly to the intake manifold with the 4 bolts.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

      Note

      If the throttle body with motor assembly has been struck or dropped, replace it.

    2. Connect the throttle body with motor assembly connector.

    3. B0088PPC01
      *1 No. 2 Water By-pass Hose
      *2 No. 3 Water By-pass Hose
      *a Top
      *b Left of Vehicle
      *c Rear of Vehicle
      *d Paint Mark
      *e Protrusion
      *f Protrusion Location

      Connect the No. 3 water by-pass hose to the throttle body with motor assembly and slide the clip to secure it.

      Note


      • Align the paint mark of the No. 3 water by-pass hose with the protrusion of the throttle body with motor assembly.

      • Make sure to position the clip as shown in the illustration.

    4. Connect the No. 2 water by-pass hose to the throttle body with motor assembly and slide the clip to secure it.

      Note

      Make sure to position the clip as shown in the illustration.

  3. INSTALL AIR CLEANER CAP WITH AIR CLEANER HOSE


    1. B0085HVC01
      *a 12 to 18 mm (0.472 to 0.709 in.)
      *b Cutout
      *c Protrusion

      Install the air cleaner cap with air cleaner hose to the throttle body with motor assembly as shown in the illustration.

      Note

      Align the cutout of the air cleaner hose with the protrusion of the throttle body with motor assembly.

    2. Tighten the hose clamp in the position shown in the illustration.

    3. Engage the 2 guides to connect the air cleaner cap with air cleaner hose to the air cleaner case sub-assembly.

    4. Engage the 2 air cleaner cap clamps.

    5. Engage the clamp to connect the No. 1 fuel hose sub-assembly to the fuel hose bracket.

    6. Engage the clamp to connect the heater hose to the air cleaner hose assembly.

    7. Engage the 2 clamps to connect the No. 2 fuel vapor feed hose assembly to the air cleaner hose assembly.

    8. Engage the clamp to connect the union to check valve hose to the air cleaner hose assembly.

    9. Engage the 2 wire harness clamps.

    10. Connect the mass air flow meter sub-assembly connector.

    11. Engage the clamp to connect the ventilation hose to the engine wire.

    12. B00890JC01
      *a Top
      *b Paint Mark
      *c 45°(Claw of Clip Location)

      Connect the ventilation hose to the cylinder head cover sub-assembly and slide the clip to secure it.

      Note

      Make sure to position the clip as shown in the illustration.

  4. INSTALL BATTERY

    Click here

  5. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Click here

  6. ADD ENGINE COOLANT

    Click here

  7. INSPECT FOR COOLANT LEAK

    Click here

  8. INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY

    Click here

  9. PERFORM INITIALIZATION

    Note


    • Be sure to perform this procedure after removing and reinstalling the throttle body with motor assembly or any throttle body with motor assembly components.

    • Perform the following procedure after replacing the throttle body with motor assembly or any throttle body with motor assembly components. The following procedure should also be performed if the throttle body with motor assembly is cleaned.


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Clear the DTCs.


      Powertrain > Engine > Clear DTCs

    5. Perform "Inspection After Repair".

      Click here

    6. Start the engine and check that the MIL is not illuminated. After the engine is warmed up, check that the idle speed is within the specified range with the A/C switch off.

      Standard Idle Speed
      600 to 700 rpm

      Note


      • Be sure to perform this step with all accessories off.

      • Make sure that the shift lever is in P or N.

    7. Enter the following menus: Powertrain / Engine / Data List / Throttle Position Sensor No.1 Voltage %.


      Powertrain > Engine > Data List
      Tester Display
      Throttle Position Sensor No.1 Voltage %

    8. According to the display on the GTS, read the Data List while fully depressing the accelerator pedal and check that the value is 60% or higher.

    9. Perform a road test and confirm that there are no abnormalities.