MULTI-MODE MANUAL TRANSAXLE SYSTEM, Diagnostic DTC:P0910

DTC Code DTC Name
P0910 Gate Select Actuator Circuit

DESCRIPTION

C239986C02

*a

Shift and Select Actuator Operation

*b

Shift Direction

*c

Select Direction

The shift and select actuator is operated by the TCM and changes the transaxle gear by moving the shift and select lever shaft. An electric motor (select motor) moves the shift and select lever shaft in the select direction, and the select stroke sensor, which is mounted on the shift and select actuator assembly, detects the select position. The TCM monitors the electrical current and select motor output terminal voltage, and detects malfunctions in the select motor circuit.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

MIL

Warning Indicate

Memory

P0910

Gate Select Actuator Circuit

The TCM detects the following conditions:

(1-trip detection logic)

  1. Select motor is not energized.

  2. Voltage of select motor terminal (MSL+ or MSL-) is less than threshold*1, or more than threshold*2 for 0.5 seconds.

The TCM detects the following conditions:

(1-trip detection logic)

  1. Select motor is energized.

  2. Target select motor current is more than 5 A.

  3. Actual select motor current is less than 1 A*3.

The TCM detects the following conditions:

(1-trip detection logic)

  1. Select motor is not energized.

  2. Difference between maximum and minimum voltages of select motor terminal (MSL+ or MSL-) is more than threshold*4 for 0.5 seconds.

  • Shift and select actuator assembly (select motor)

  • Wire harness or connector

  • TCM

Does not come on

Comes on

DTC stored

  • *1: A short between the select motor circuit and the body ground is suspected.

  • *2: A short between the select motor circuit and the +B circuit is suspected.

  • *3: An open in the select motor circuit is suspected. When the motor current does not flow to the ECU terminals despite the ECU ordering the select motor to operate, the ECU stores this DTC.

  • *4: An open in the select motor circuit is suspected. When the difference is more than the threshold despite the ECU not ordering the select motor to operate, the ECU stores this DTC.

WIRING DIAGRAM

C279536E02

CAUTION / NOTICE / HINT

Note:

When installing parts related to the multi-mode manual transaxle system, perform the initialization and learning and synchronization position calibration procedures. In addition, the required operations differ according to the parts to be installed. Proceed with the operation in the order shown in the table below.

Table 1. After Installation

Part Installed

Part Installed

See Procedure

  • Transaxle assembly

  • Transaxle parts (inside gear box)

  • TCM

  • Clutch actuator assembly

  • Clutch disc and clutch cover

  • Clutch release with bearing cylinder assembly

  • Flywheel

  • Crankshaft

1. Initialization of multi-mode manual transaxle system

[Tester display: Initialization of ECU]

Click here

2. Learning of multi-mode manual transaxle system

3. Synchronization position calibration

  • Shift and select actuator

  • Shift stroke sensor

  • Select stroke sensor

1. Initialization of multi-mode manual transaxle system

[Tester display: Initialization of transmission]

2. Learning of multi-mode manual transaxle system

3. Synchronization position calibration

  • Clutch stroke sensor

1. Initialization of multi-mode manual transaxle system

[Tester display: Initialization of clutch]

2. Learning of multi-mode manual transaxle system

If the sensor or actuator is installed without the initialization and learning procedures, it may cause driving performance degradation or system component breakage.

PROCEDURE

  1. INSPECT TCM (MSL TERMINAL VOLTAGE)

    Click here

    Result

    Proceed to

    OK

    NG
    OK

    CHECK INTERMITTENT PROBLEMS

    Click here

    NG

  2. CHECK TERMINAL CONDITION (TCM)

    Click here

    Result

    Proceed to

    OK

    NG
    NG

    CONNECT CORRECTLY

    OK

  3. INSPECT SELECT MOTOR CIRCUIT

    Click here

    Result

    Proceed to

    OK

    NG
    NG

    CHECK TERMINAL CONDITION (SELECT MOTOR)Click here

    OK

  4. REPLACE TCM

    1. Replace the TCM.

      for LHD:Click hereClick here

      for RHD:Click hereClick here

    Result

    Proceed to

    NEXT
    NEXT

  5. PERFORM INITIALIZATION

    1. Perform the initialization and learning procedure.

      Click here

    Result

    Proceed to

    NEXT
    NEXT

    END

  6. CHECK TERMINAL CONDITION (SELECT MOTOR)

    Click here

    Result

    Proceed to

    OK

    NG
    NG

    CONNECT CORRECTLY

    OK

  7. CHECK HARNESS AND CONNECTOR (TCM - SELECT MOTOR)

    Click here

    Result

    Proceed to

    OK

    NG
    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  8. INSPECT SHIFT AND SELECT ACTUATOR ASSEMBLY (SELECT MOTOR)

    Click here

    Result

    Proceed to

    OK

    NG
    OK

    CHECK INTERMITTENT PROBLEMS

    Click here

    NG

  9. REPLACE SHIFT AND SELECT ACTUATOR ASSEMBLY

    1. Replace the shift and select actuator assembly.

      Click here

    Result

    Proceed to

    NEXT
    NEXT

  10. PERFORM INITIALIZATION

    1. Perform the initialization and learning procedure.

      Click here

    Result

    Proceed to

    NEXT
    NEXT

    END