PARKING BRAKE CABLE (for 2WD) INSTALLATION


  1. INSTALL NO. 3 PARKING BRAKE CABLE ASSEMBLY

    A01E0RWE02
    Text in Illustration
    *1 No. 3 Parking Brake Cable *2 No. 3 Clip

    1. Install the No. 3 parking brake cable with the 4 bolts and nut.

      Torque:
      for Bolt A, Nut C
      26 N*m  { 260 kgf*cm, 19 ft.*lbf }
      for Bolt B
      14 N*m  { 143 kgf*cm, 10 ft.*lbf }

    2. Install the No. 3 clip.

    3. Connect the No. 3 parking brake cable to the parking brake shoe lever LH and backing plate LH.


      1. Connect the No. 3 parking brake cable to the backing plate with the 2 bolts.

        Torque:
        9.0 N*m  { 92 kgf*cm, 80 in.*lbf }

      2. Connect the No. 3 parking brake cable to the parking brake shoe lever Click here.

  2. INSTALL NO. 2 PARKING BRAKE CABLE ASSEMBLY

    A01DYV0E02
    Text in Illustration
    *1 No. 2 Parking Brake Cable *2 Parking Brake Equalizer

    1. Install the No. 2 parking brake cable with the 4 bolts.

      Torque:
      for Bolt A
      26 N*m  { 260 kgf*cm, 19 ft.*lbf }
      for Bolt B
      14 N*m  { 143 kgf*cm, 10 ft.*lbf }

    2. Connect the No. 2 parking brake cable to the parking brake equalizer and apply MP grease to the connecting portion.

    3. Connect the cable to the parking brake shoe lever RH and backing plate RH.


      1. Connect the No. 2 parking brake cable to the backing plate with the 2 bolts.

        Torque:
        9.0 N*m  { 92 kgf*cm, 80 in.*lbf }

      2. Connect the No. 2 parking brake cable to the parking brake shoe lever Click here.

        Tech Tips

        Use the same procedure described for the LH side.

  3. INSTALL NO. 1 PARKING BRAKE CABLE ASSEMBLY

    A01DZ15E01
    Text in Illustration
    *1 No. 1 Parking Brake Cable *2 No. 3 Parking Brake Cable
    *3 Parking Brake Equalizer *4 Cable Support Bracket

    1. Connect the No. 1 parking brake cable to the parking brake lever Click here.

    2. Install the No. 1 parking brake cable clamp to the No. 1 parking brake cable.

    3. Install the No. 1 parking brake cable with the bolt.

      Torque:
      5.0 N*m  { 51 kgf*cm, 44 in.*lbf }

    4. Connect the No. 1 parking brake cable to the parking brake equalizer.

    5. Connect the No. 1 parking brake cable to the No. 3 parking brake cable and apply MP grease to the connecting portion.

    6. Install the pin and No. 1 clip.

    7. Attach the No. 1 parking brake cable to the cable support bracket.

    8. Install the No. 1 heat insulator with the 2 bolts.

      Torque:
      6.0 N*m  { 61 kgf*cm, 53 in.*lbf }

  4. CHECK REAR BRAKE DRUM INSTALLATION

  5. INSTALL REAR BRAKE DRUM SUB-ASSEMBLY AND NEW GASKET


    1. Check that each part is installed properly.

      A01DXCOE01
    2. A01E2IE

      Measure the inside diameter of the drum and diameter of the brake shoes. Check that the difference between the diameters is the correct shoe clearance.

      Standard shoe clearance
      0.5 mm (0.0197 in.)

      Note

      There should be no oil or grease on the contact surfaces of the shoe lining and drum.

  6. INSTALL REAR WHEEL


    1. Install the wheel.

      Torque:
      152 N*m  { 1,550 kgf*cm, 112 ft.*lbf, for steel wheel }
      121 N*m  { 1,234 kgf*cm, 89 ft.*lbf, for aluminum wheel }

  7. ADJUST PARKING BRAKE

    Click here

  8. INSTALL CONSOLE BOX ASSEMBLY

    Click here

  9. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.