REAR NO. 1 SEAT ASSEMBLY(for 60/40 Split Double-folding Seat Type LH Side) INSTALLATION

CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.

Tip:

A bolt without a torque specification is shown in the standard bolt chart (Click here).

PROCEDURE

  1. INSTALL REAR SEAT CUSHION LOCK STRIKER

    1. Install the rear seat cushion lock striker with the 2 bolts.

      13 N*m

      127 kgf*cm

      9 ft.*lbf

  2. INSTALL REAR NO. 2 SEATBACK LOCK STRIKER SUB-ASSEMBLY LH

    B311267N01

    1. Attach the claw and temporarily install the rear No. 2 seatback lock striker sub-assembly LH with the 2 bolts.

    2. Tighten the bolts in the order indicated in the illustration.

      37 N*m

      377 kgf*cm

      27 ft.*lbf

  3. INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH

    Click hereClick here

  4. INSTALL FRONT DECK SIDE TRIM COVER (w/ Tonneau Cover)

    Click hereClick here

  5. INSTALL NO. 1 TONNEAU COVER HOLDER CAP (w/o Tonneau Cover)

    Click hereClick here

  6. INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM HOOK

    Click hereClick here

  7. INSTALL REAR NO. 1 SEAT OUTER LAP BELT ANCHOR COVER

    Click hereClick here

  8. INSTALL REAR FLOOR CARPET ASSEMBLY

    Click hereClick here

  9. INSTALL REAR FLOOR MAT REAR SUPPORT PLATE

    Click hereClick here

  10. INSTALL NO. 1 DECK BOARD SUB-ASSEMBLY

    Click hereClick here

  11. INSTALL FRONT LUGGAGE COMPARTMENT TRIM COVER

    Click hereClick here

  12. INSTALL TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)

    Click hereClick here

  13. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH

    Click hereClick here

  14. INSTALL REAR DOOR SCUFF PLATE LH

    Click hereClick here

  15. INSTALL REAR SEATBACK LOCK CONTROL LEVER BASE LH

    1. Attach the No. 2 seatback lock striker sub-assembly LH cable clamp to connect the No. 2 seatback lock striker sub-assembly LH cable.

    2. B237982

      Move the rear seatback lock control lever base LH in the direction of the arrow to attach the 2 guides.

    3. Attach the 6 claws to install the rear seatback lock control lever base LH.

  16. INSTALL REAR SEATBACK HINGE SUB-ASSEMBLY LH

    1. Install the rear seatback hinge sub-assembly LH with the bolt.

      18 N*m

      184 kgf*cm

      13 ft.*lbf

  17. INSTALL REAR SEATBACK ASSEMBLY LH

    B311268C01

    *1

    Positioning Wire

    1. Fold down the rear seatback assembly LH, set the seatback positioning wire on the rear seatback hinge sub-assembly LH, and then temporarily install the bolt to the rear seatback hinge sub-assembly LH.

      Note:

      Be careful not to damage the vehicle body.

    2. Restore the rear seatback assembly LH to the upright position and temporarily install the rear seatback assembly LH with the 2 bolts.

    3. Tighten the bolts in the order indicated in the illustration.

      37 N*m

      377 kgf*cm

      27 ft.*lbf

  18. INSTALL REAR SEATBACK BOARD CARPET ASSEMBLY LH

    1. Attach the 4 claws and 5 clips to install the rear seatback board carpet assembly LH.

  19. INSTALL REAR SEATBACK COVER

    1. Attach the 4 claws to install the rear seatback cover.

    2. Restore the rear seatback assembly LH to the upright position and lock it.

  20. INSTALL REAR SEAT HEADREST ASSEMBLY

    1. B290750C01

      *1

      Rear Seat Headrest Handle

      Install the rear seat headrest assembly.

      Note:

      When installing the rear seat headrest assembly, make sure the rear seat headrest handle is facing the outside of the vehicle.

  21. INSTALL REAR SEAT CUSHION ASSEMBLY LH

    B247660N01

    1. Temporarily install the rear seat cushion assembly LH with the 2 bolts.

      Note:

      Be careful not to damage the vehicle body.

    2. Tighten the bolts in the order indicated in the illustration.

      37 N*m

      377 kgf*cm

      27 ft.*lbf

    3. Lock the rear seat cushion assembly LH.

  22. INSTALL REAR SEAT CUSHION HINGE COVER LH

    1. Attach the 3 claws to install the rear seat cushion cover LH.

  23. INSTALL REAR SEAT CUSHION HINGE COVER

    1. Attach the 3 claws to install the rear seat cushion hinge cover.