BLIND SPOT MONITOR SYSTEM DATA LIST / ACTIVE TEST

  1. DATA LIST

    Note:

    In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

    Tip:

    Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

    • *1: for LHD

    • *2: for RHD

    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Enter the following menus: Body Electrical / Blind spot monitor Master or Blind spot monitor Slave / Data List.

    4. Read the Data List according to the display on the GTS.

      Body Electrical > Blind Spot Monitor Master > Data List

      Tester Display

      Measurement Item

      Range

      Normal Condition

      Diagnostic Note

      Main Switch

      Blind spot monitor main switch (warning cancel switch assembly*1 or telltale light assembly*2) / OFF or ON

      OFF or ON

      OFF: Blind spot monitor main switch (warning cancel switch assembly*1 or telltale light assembly*2) off

      ON: Blind spot monitor main switch (warning cancel switch assembly*1 or telltale light assembly*2) on

      -

      Warning Indicator Turning on(Master)

      State of the outer rear view mirror indicator LH turning on

      OFF or ON

      OFF: The following conditions are not met

      ON: All of the following conditions are met

      • Not during initial check

      • Vehicle detected in left hand side warning area

      • Left turn signal: off

      • Vehicle speed 40 km/h (25 mph) or more

      • Shift lever in any position except R

      • Blind spot monitor warning light not illuminated

      -

      Warning Indicator Flashing(Master)

      State of the outer rear view mirror indicator LH flashing

      OFF or ON

      OFF: The following conditions are not met

      ON: All of the following conditions are met

      • Not during initial check

      • Vehicle detected in left hand side warning area

      • Left turn signal: on

      • Vehicle speed 40 km/h (25 mph) or more

      • Shift lever in any position except R

      • Blind spot monitor warning light not illuminated

      -

      Main Switch Indicator Status

      State of the blind spot monitor indicator on the blind spot monitor main switch (warning cancel switch assembly*1 or telltale light assembly*2)

      OFF or ON

      OFF: Indicator not illuminated

      ON: Indicator illuminated

      -

      Warning Indicator Input Circuit Voltage

      Outer rear view mirror indicator voltage

      Min.: 0 V, Max.: 25.5 V

      Not illuminated: 0 V

      Illuminated: 2.5 to 7.5 V

      -

      Warning Indicator Input Circuit Current

      Outer rear view mirror indicator current

      Min.: 0 mA, Max.: 255 mA

      Not illuminated: 0 mA

      Illuminated: 5 to 100 mA

      -

      Main Switch Indicator Input Circuit Voltage

      Blind spot monitor indicator on the blind spot monitor main switch (warning canceling switch assembly*1 or telltale light assembly*2) voltage

      Min.: 0 V, Max.: 25.5 V

      Always: 9 to 16 V

      -

      Turn Switch State

      State of the headlight dimmer switch assembly (turn signal light switch)

      Left ON, Right ON or OFF

      Left ON: Left side of turn signal light switch on

      Right ON: Right side of turn signal light switch on

      OFF: Turn signal light switch off

      -

      Reverse (Only for AT/CVT)

      State of the shift position R signal

      OFF or ON

      ON: Shift lever in R

      OFF: Shift lever in any position except R

      -

      Vehicle Speed

      Vehicle speed signal

      Min.: 0 km/h (0 mph), Max.: 326 km/h (203 mph)

      Vehicle stopped: 0 km/h (0 mph)

      -

      Steering Angle

      Steering angle sensor

      Min.: -3072°, Max.: 3070.5°

      Left turn: Increases

      Right turn: Decreases

      -

      Power Supply Voltage

      Power supply voltage

      Min.: 0 V, Max.: 50 V

      Always: 11 to 14 V

      -

      Indicator Light Control State

      Outer rear view mirror indicator dimming state

      Dim OFF or Dim ON

      Dim OFF: Indicator not dimmed

      Dim ON: Indicator dimmed

      -

      HV Flag

      Hybrid vehicle

      OFF or ON

      OFF: Non-hybrid vehicle

      ON: Hybrid vehicle

      -

      VGRS Flag

      VGRS installed

      VGRS installed / OFF or ON

      OFF: VGRS not installed

      ON: VGRS installed

      -

      Main SW Inspection Completeness Flag

      Completion of inspection for blind spot monitor main switch (warning cancel switch assembly*1 or telltale light assembly*2)

      Incompl or Compl

      Incompl: Inspection not completed

      Compl: Inspection completed

      Changes to Compl when the blind spot monitor main switch (warning cancel switch assembly*1 or telltale light assembly*2) is changed from off to on during Test Mode.

      Beam Axis Inspection Completeness Flag

      Completion of beam axis inspection

      Incompl or Compl

      Incompl: Inspection not completed

      Compl: Inspection completed

      Changes to Compl when Test Mode has been entered.

      Destination Undefined Flag

      Destination determination

      Unfixed or Fixed

      Fixed: Sensor destination information determined according to CAN destination information

      -

      Angle Adjustment by Auto Alignment

      Angle adjusted using auto alignment

      Min.: Under -12.8 deg, Max.: Over 12.7 deg

      Angle adjusted using auto alignment is displayed

      When the adjusted angle is 12.7 degrees or more, "Over 12.7" is displayed and when it is -12.8 degrees or less, "Under -12.8" is displayed

      Mirror LED Control Frequency

      This shows the frequency for the mirror LED control

      Min.: 1500 Hz, Max.: 2400 Hz

      Always: 1500 Hz

      -

      Setting of Warning Indicator Current (Dim OFF)

      Set current of the outer rear view mirror indicator when not dimmed

      Min.: 0 mA, Max.: 100 mA

      Always: 0 to 100 mA

      -

      Setting of Warning Indicator Current (Dim ON)

      Set current of the outer rear view mirror indicator when dimmed

      Min.: 0 mA, Max.: 100 mA

      Always: 0 to 100 mA

      -

      Mirror LED Duty Ratio (Blinking)

      Duty ratio of the outer rear view mirror indicator when blinking

      Min.: 0%, Max.: 100%

      Always: 50 %

      -

      Main Switch LED Control Frequency

      Frequency of the blind spot monitor indicator on the blind spot monitor main switch (warning cancel switch assembly*1 or telltale light assembly*2) when operating

      Min.: 100 Hz, Max.: 500 Hz

      Always: 100 Hz

      -

      Main Switch LED Duty Ratio (Bright Condition)

      Duty ratio of the blind spot monitor indicator on the blind spot monitor main switch (warning cancel switch assembly*1 or telltale light assembly*2) when illuminated

      Min.: 0 %, Max.: 100 %

      100 %

      -

      Main Switch LED Duty Ratio (Dimmed Condition)

      Duty ratio of the blind spot monitor indicator on the blind spot monitor main switch (warning cancel switch assembly*1 or telltale light assembly*2) when dimmed

      Min.: 0 %, Max.: 100 %

      30 %

      -

      Number of DTC

      Number of DTCs

      Min.: 0, Max.: 255

      When system is normal: 0

      When a malfunction is detected: More than 0

      -

      Body Electrical > Blind Spot Monitor Slave > Data List

      Tester Display

      Measurement Item

      Range

      Normal Condition

      Diagnostic Note

      Warning Indicator Turning on(Slave)

      State of the outer rear view mirror indicator RH turning on

      OFF or ON

      OFF: The following conditions are not met

      ON: All of the following conditions are met

      • Not during initial check

      • Vehicle detected in right hand side warning area

      • Right turn signal: off

      • Vehicle speed 40 km/h (25 mph) or more

      • Shift lever in any position except R

      • Blind spot monitor warning light not illuminated

      -

      Warning Indicator Flashing(Slave)

      State of the outer rear view mirror indicator RH flashing

      OFF or ON

      OFF: The following conditions are not met

      ON: All of the following conditions are met

      • Not during initial check

      • Vehicle detected in right hand side warning area

      • Vehicle speed 40 km/h (25 mph) or more

      • Right turn signal: on

      • Shift lever in any position except R

      • Blind spot monitor warning light not illuminated

      -

      Buzzer Sound Status

      State of the rear cross traffic alert buzzer (blind spot monitor buzzer)

      OFF or ON

      OFF: Buzzer not sounding

      ON: All of the following conditions are met:

      • Not during initial check

      • Vehicle detected in warning area of rear cross traffic alert

      • Speed difference between driver's vehicle and target vehicle is 1.5 m/s or more

      • Shift lever in R

      • No DTC output

      w/ RCTA

      Warning Indicator Input Circuit Voltage

      Outer rear view mirror indicator voltage

      Min.: 0 V, Max.: 25.5 V

      Not illuminated: 0 V

      Illuminated: 2.5 to 7.5 V

      -

      Warning Indicator Input Circuit Current

      Outer rear view mirror indicator current

      Min.: 0 mA, Max.: 255 mA

      Not illuminated: 0 mA

      Illuminated: 5 to 100 mA

      -

      Buzzer Input Circuit Voltage

      Rear cross traffic alert buzzer (blind spot monitor buzzer) voltage

      Min.: 0 V, Max.: 25.5 V

      Not sounding buzzer: 11 to 14 V Sounding buzzer: Alternating between 0 to 14 V

      w/ RCTA

      Turn Switch State

      State of the headlight dimmer switch assembly (turn signal light switch)

      Left ON, Right ON or OFF

      Left ON: Left side of turn signal light switch on

      Right ON: Right side of turn signal light switch on

      OFF: Turn signal light switch off

      -

      Reverse (Only for AT/CVT)

      State of the shift position R signal

      OFF or ON

      ON: Shift lever in R

      OFF: Shift lever in any position except R

      -

      Reverse (Only for MT)

      State of the shift position R signal

      OFF or ON

      ON: Shift lever in R

      OFF: Shift lever in any position except R

      -

      Vehicle Speed

      Vehicle speed signal / Min.: 0 km/h (0 mph)

      Min.: 0 km/h (0 mph), Max.: 326 km/h (203 mph)

      Vehicle stopped: 0 km/h (0 mph)

      -

      Steering Angle

      Steering angle sensor

      Min.: -3072°, Max.: 3070.5°

      Left turn: Increases

      Right turn: Decreases

      -

      Power Supply Voltage

      Power supply voltage

      Min.: 0 V, Max.: 50 V

      Always: 11 to 14 V

      -

      Indicator Light Control State

      Outer rear view mirror indicator dimming state

      Dim OFF or Dim ON

      Dim OFF: Indicator not dimmed

      Dim ON: Indicator dimmed

      -

      HV Flag

      Hybrid vehicle

      OFF or ON

      OFF: Non-hybrid vehicle

      ON: Hybrid vehicle

      -

      VGRS Flag

      VGRS installed

      OFF or ON

      OFF: VGRS not installed

      ON: VGRS installed

      -

      Beam Axis Inspection Completeness Flag

      Completion of beam axis inspection

      Incompl or Compl

      Incompl: Inspection not completed

      Compl: Inspection completed

      Changes to Compl when Test Mode has been entered.

      Destination Undefined Flag

      Destination determination

      Unfixed or Fixed

      Fixed: Sensor destination information determined according to CAN destination information

      -

      Angle Adjustment by Auto Alignment

      Angle adjusted using auto alignment

      Min.: Under -12.8 deg, Max.: Over 12.7 deg

      Angle adjusted using auto alignment is displayed

      When the adjusted angle is 12.7 degrees or more, "Over 12.7" is displayed and when it is -12.8 degrees or less, "Under -12.8" is displayed

      Mirror LED Control Frequency

      This shows the frequency for the mirror LED control

      Min.: 1500 Hz, Max.: 2400 Hz

      Always: 1500 Hz

      -

      Setting of Warning Indicator Current (Dim OFF)

      Set current of the outer rear view mirror indicator when not dimmed

      Min.: 0 mA, Max.: 100 mA

      Always: 0 to 100 mA

      -

      Setting of Warning Indicator Current (Dim ON)

      Set current of the outer rear view mirror indicator when dimmed

      Min.: 0 mA, Max.: 100 mA

      Always: 0 to 100 mA

      -

      Mirror LED Duty Ratio (Blinking)

      Duty ratio of the outer rear view mirror indicator when blinking

      Min.: 0%, Max.: 100%

      Always: 50 %

      -

      Number of DTC

      Number of DTCs

      Min.: 0, Max.: 255

      When system is normal: 0

      When a malfunction is detected: More than 0

      -