REPAIR INSTRUCTION PRECAUTION


  1. BASIC REPAIR HINT


    1. HINTS ON OPERATIONS

      B007XLQN13
      1 Attire
      • Always wear a clean uniform.

      • A hat and safety shoes must be worn.

      2 Vehicle protection Prepare a grille cover, fender cover, seat cover and floor mat before starting work.
      3 Safety procedures
      • When working with 2 or more persons, be sure to check the safety of one another.

      • When working with the engine running, make sure to provide ventilation for exhaust fumes in the workshop.

      • If working on high temperature, high pressure, rotating, moving or vibrating parts, wear appropriate safety equipment and take extra care not to injure yourself or others.

      • When jacking up the vehicle, be sure to support the vehicle at the specified locations with safety stands.

      • When lifting up the vehicle, use appropriate safety equipment.

      4 Preparation of tools and measuring equipment Before starting work, prepare a tool stand, SST, measuring equipment, oil, and any replacement parts required.
      5 Removal and installation, disassembly and assembly operations
      • Diagnose with a thorough understanding of proper procedures and of the reported problem.

      • Before removing any parts, check the general condition of the assembly and for deformation and damage.

      • If the procedure is complicated, take notes. For example, note the total number of electrical connections, bolts or hoses removed. Add matchmarks to ensure reassembly of components in the original positions. Temporarily mark hoses and their fittings if needed.

      • Clean and wash the removed parts if necessary and assemble them after a thorough check.

      6 Removed parts
      • Place the removed parts in a separate box to avoid mixing them up with new parts or contaminating the new parts.

      • For non-reusable parts such as gaskets, O-rings and self-locking nuts, replace them with new ones as instructed in this manual.

      • Retain the removed parts for customer inspection, if requested.

      7* Checks to perform after work is finished
      • Make sure that removed and installed parts (oil filler cap, level dipstick, floor mat, etc.) are properly installed/tightened.

      • Make sure that none of the cloths or tools that were used have been left in the engine compartment or within the vehicle.

      • Check that there are no oil leaks.

      CAUTION:

      *: Be sure to perform these checks properly, not performing these checks properly after finishing work can lead to a serious accident or injury.

    2. JACKING UP AND SUPPORTING THE VEHICLE


      1. Care must be taken when jacking up and supporting the vehicle. Be sure to lift and support the vehicle at the proper locations.

    3. B007YO4C01
      *a Seal Lock Adhesive

      PRECOATED PARTS


      1. Precoated parts are bolts and nuts that are coated with seal lock adhesive at the factory.

      2. If a precoated part is retightened, loosened or moved in any way, it must be recoated with the specified adhesive.

      3. When reusing a precoated part, clean off the old adhesive and dry the part with compressed air. Then apply new seal lock adhesive appropriately to that part.

      4. Some seal lock agents harden slowly. You may have to wait for the seal lock adhesive to harden.

    4. GASKETS


      1. When necessary, use a sealer on gaskets to prevent leaks.

    5. BOLTS, NUTS AND SCREWS


      1. Carefully follow all the specifications for tightening torque. Always use a torque wrench.

      2. Make sure that no foreign matter (burrs, paint, etc.) gets trapped under the heads of the bolts and nuts when tightening them.

    6. B007XFNC01
      *a Incorrect
      *b Correct

      FUSES


      1. When inspecting a fuse, check that the wire of the fuse is not broken.

      2. If the wire of a fuse is broken, confirm that there are no shorts in its circuit.

      3. When a fuse is replaced, a fuse with the same amperage rating must be used.

        Illustration Symbol Part Name Abbreviation
        B007YJU B007ZTN FUSE FUSE
        B007ZLS B007YJY MEDIUM CURRENT FUSE M-FUSE
        B007XKN B007XUX HIGH CURRENT FUSE H-FUSE
        B007WPI B007YQH FUSIBLE LINK FL
        B007YJI B007YCK CIRCUIT BREAKER CB
        B00802X B007XUX FUSIBLE LINK FL
    7. CLIPS


      1. The removal and installation methods of typical clips used for vehicle body parts are shown in the table below.

        Tech Tips

        If clips are damaged during a procedure, always replace the damaged clips with new ones.

        Shape (Example) Removal/Installation
        B007YLL

        Remove the clips with a clip remover or pliers.

        B007YOF
        B007XOR

        Remove the clips using a clip remover or a screwdriver with its tip wrapped with protective tape.

        B007Y00
        B007XS9

        Remove the clips with a wide scraper to prevent panel damage.

        B007XQW
        B007WP3

        Remove the clips by pushing the center pin through and pulling out the shell.

        B007ZDB
        B007ZXQ

        Remove the clips by unscrewing the center pin and prying out the shell.

        B007ZTJ
        B007ZY1

        Remove the clips by prying out the pin using a screwdriver with its tip wrapped with protective tape and then prying out the shell.

        B007WPO
    8. CLAWS


      1. The removal and installation methods of typical claws used for vehicle body parts are shown in the table below.

        Tech Tips

        If claws are damaged during a procedure, always replace the cap or cover that has damaged claws with a new one.

        Shape (Example) Illustration / Procedures
        B007XO1

        Disengage the claws using a screwdriver with its tip wrapped with protective tape to remove the caps or covers.

        B007ZFM
        B007XSY

        Disengage the claws using a screwdriver with its tip wrapped with protective tape to remove the caps or covers.

        B007WP5
        B007ZCD

        Disengage the claws using a screwdriver with its tip wrapped with protective tape to remove the caps or covers.

        B007Z22
    9. HINGES, GUIDES, CLAMPS, PINS, ETC.


      1. The removal and installation methods of typical hinges, guides, clamps and pins used for vehicle body parts are shown in the table below.

        Tech Tips

        If clamps are damaged during a procedure, always replace the cap or cover that has damaged clamps with a new one.

        Shape (Example) Removal/Installation
        B007X6J

        Pull away from the pins to disengage.

        B007XAY
        B007WYJ

        Disengage the pins by pulling.

        B007WYQ
        B007XXI

        Remove the clamps with pliers.

        B007X50
        B007YK7

        Disengage the pins by pulling.

        B007XH1
    10. REMOVAL AND INSTALLATION OF VACUUM HOSES


      1. B007YNGC01
        *a Incorrect
        *b Correct

        To disconnect a vacuum hose, pull and twist it from the end of the hose. Do not pull it from the middle of the hose as this may damage the hose.

      2. B007YEJ

        When disconnecting vacuum hoses, use tags to identify where they should be reconnected.

      3. After completing any hose related repairs, double-check that the vacuum hoses are properly connected. The label under the hood shows the proper layout.

      4. When using a vacuum gauge, never force the hose onto a connector that is too large. If a hose has been stretched, air may leak. Use a step-down adapter if necessary.

    11. B007ZNPN01

      TORQUE WHEN USING TORQUE WRENCH WITH EXTENSION TOOL


      1. B008051N01

        Use the formula below to calculate special torque values for situations where SST or an extension tool is combined with a torque wrench.

        T' Reading of torque wrench (N*m (kgf*cm, ft.*lbf))
        T Torque (N*m (kgf*cm, ft.*lbf))
        L1 Length of SST or extension tool (cm (in.))
        L2 Length of torque wrench (cm (in.))

        Note

        If an extension tool or SST is combined with a torque wrench and used to tighten to a torque specification in this manual, the actual torque will be excessive and parts will be damaged.

  2. FOR VEHICLES EQUIPPED WITH SRS AIRBAG AND SEAT BELT PRETENSIONER

    This vehicle is equipped with a Supplemental Restraint System (SRS).

    CAUTION:


    • Before performing pre-disposal deployment of any SRS parts, review and closely follow all applicable environmental and hazardous material regulations. Pre-disposal deployment may be considered hazardous material treatment.

    • Failure to carry out the service operations in the correct sequence could cause the SRS to unexpectedly deploy during servicing and lead to a serious injury. Furthermore, if a mistake is made when servicing the SRS, it is possible that the SRS may fail to operate properly. Before servicing (including removal or installation of parts, inspection or replacement), be sure to read the following section carefully.


    1. GENERAL NOTICE


      1. As malfunctions of the SRS are difficult to confirm, Diagnostic Trouble Codes (DTCs) become the most important source of information when troubleshooting. When troubleshooting the SRS, always check for DTCs before disconnecting the battery.

      2. Work must be started at least 90 seconds after the engine switch is turned off and the cable is disconnected from the negative (-) battery terminal.

        The SRS is equipped with a back-up power source. If work is started within 90 seconds of turning the engine switch off and disconnecting the cable from the negative (-) battery terminal, the SRS may deploy.

        When the cable is disconnected from the negative (-) battery terminal, the clock and audio system memory will be cleared. Before starting work, make a note of the settings of each memory system. When work is finished, reset the clock and audio system as before.

        CAUTION:

        Never use a back-up power source (battery or other) to avoid clearing the system memory. The back-up power source may inadvertently power the SRS and cause it to deploy.

      3. If the vehicle has been involved in a minor collision where the SRS does not deploy, the steering pad, front passenger airbag assembly, knee airbag assembly, seat side airbag assemblies, curtain shield airbag assemblies, front seat cushion airbag assembly and seat outer belt assemblies should be inspected before further use of the vehicle.

      4. Never use SRS parts from another vehicle. When replacing parts, use new ones.

      5. Before performing repairs, remove the airbag sensor assemblies if impacts are likely to be applied to the sensor during repairs.

      6. Never disassemble and attempt to repair any of the airbag sensor assemblies or airbag assemblies.


        1. Steering pad

        2. Front passenger airbag assembly

        3. Knee airbag assembly

        4. Seat side airbag assembly

        5. Curtain shield airbag assembly

        6. Front seat cushion airbag assembly

        7. Seat outer belt assembly

      7. Replace any airbag sensor assembly or SRS parts if: 1) damage has occurred from being dropped, or 2) cracks, dents or other defects in the case, bracket or connector are present.

      8. Do not directly expose the airbag sensor assemblies or SRS parts to hot air or flames.

      9. Use a voltmeter/ohmmeter with high impedance (minimum = 10 kΩ) for troubleshooting electrical circuits.

      10. Information labels are attached to the SRS components. Follow the instructions on the labels.

      11. After work on the SRS is completed, check the SRS warning light.

    2. SPIRAL CABLE


      1. The steering wheel must be fitted correctly to the steering column with the spiral cable at the neutral position. Otherwise, cable damage and other problems may occur. Refer to the information about correct installation of the steering wheel.

        Click here

    3. STEERING PAD


      1. Always place a removed or new steering pad with the deployment surface facing upward. Placing the steering pad with the deployment surface facing downward could cause a serious accident if the airbag deploys. Also, do not place anything on top of the steering pad.

      2. Never measure the resistance of the airbag squib. This may cause the airbag to deploy, which could cause serious injury.

      3. Grease or detergents of any kind should not be applied to the steering pad.

      4. Store the steering pad in an area where the ambient temperature is below 93°C (199°F), the humidity is not high and there is no electrical noise.

      5. Before using an electric welder anywhere on the vehicle, disconnect the center airbag sensor assembly connectors. These connectors contain shorting springs. This feature reduces the possibility of the airbag deploying due to current entering the squib wiring.

      6. When disposing of the vehicle or steering pad by itself, the airbag should be deployed using SST before disposal. Deploy the airbag in a safe place away from electrical noise.

        Click here

    4. FRONT PASSENGER AIRBAG ASSEMBLY


      1. Always place a removed or new front passenger airbag assembly with the deployment surface facing upward. Placing the airbag assembly with the airbag deployment surface facing downward could cause a serious accident if the airbag deploys.

      2. Never measure the resistance of the airbag squib. This may cause the airbag to deploy, which could cause serious injury.

      3. Grease or detergents of any kind should not be applied to the front passenger airbag assembly.

      4. Store the front passenger airbag assembly in an area where the ambient temperature is below 93°C (199°F), the humidity is not high and there is no electrical noise.

      5. Before using an electric welder anywhere on the vehicle, disconnect the center airbag sensor assembly connectors. These connectors contain shorting springs. This feature reduces the possibility of the airbag deploying due to current entering the squib wiring.

      6. When disposing of the vehicle or front passenger airbag assembly by itself, the airbag should be deployed using SST before disposal. Deploy the airbag in a safe place away from electrical noise.

        Click here

    5. KNEE AIRBAG ASSEMBLY


      1. Always place a removed or new knee airbag assembly with the airbag deployment surface facing upward. Placing the airbag assembly with the airbag deployment surface facing downward could cause a serious accident if the airbag deploys.

      2. Never measure the resistance of the airbag squib. This may cause the airbag to deploy, which could cause serious injury.

      3. Grease or detergents of any kind should not be applied to the knee airbag assembly.

      4. Store the knee airbag assembly in an area where the ambient temperature is below 93°C (199°F), the humidity is not high and there is no electrical noise.

      5. Before using an electric welder anywhere on the vehicle, disconnect the center airbag sensor assembly connectors. These connectors contain shorting springs. This feature reduces the possibility of the airbag deploying due to current entering the squib wiring.

      6. When disposing of the vehicle or a knee airbag assembly by itself, the airbag should be deployed using SST before disposal. Deploy the airbag in a safe place away from electrical noise.

        Click here

    6. SEAT SIDE AIRBAG ASSEMBLY


      1. Always place a removed or new seat side airbag assembly with the airbag deployment surface facing upward.

      2. Never measure the resistance of the airbag squib. This may cause the airbag to deploy, which could cause serious injury.

      3. Grease or detergents of any kind should not be applied to the seat side airbag assembly.

      4. Store the seat side airbag assembly in an area where the ambient temperature is below 93°C (199°F), the humidity is not high and there is no electrical noise.

      5. Before using an electric welder anywhere on the vehicle, disconnect the center airbag sensor assembly connectors. These connectors contain shorting springs. This feature reduces the possibility of the airbag deploying due to current entering the squib wiring.

      6. When disposing of the vehicle or a seat side airbag assembly by itself, the airbag should be deployed using SST before disposal. Deploy the airbag in a safe place away from electrical noise.

        for Front Side: Click here

        for Rear Side: Click here

    7. FRONT SEAT CUSHION AIRBAG ASSEMBLY


      1. Always place a removed or new front seat cushion airbag assembly with the airbag deployment surface facing upward.

      2. Never measure the resistance of the airbag squib. This may cause the airbag to deploy, which could cause serious injury.

      3. Grease or detergents of any kind should not be applied to the front seat cushion airbag assembly.

      4. Store the front seat cushion airbag assembly in an area where the ambient temperature is below 93°C (199°F), the humidity is not high and there is no electrical noise.

      5. Before using an electric welder anywhere on the vehicle, disconnect the center airbag sensor assembly connectors. These connectors contain shorting springs. This feature reduces the possibility of the airbag deploying due to current entering the squib wiring.

      6. When disposing of the vehicle or an front seat cushion airbag assembly by itself, the airbag should be deployed using SST before disposal. Deploy the airbag in a safe place away from electrical noise.

        Click here

    8. CURTAIN SHIELD AIRBAG ASSEMBLY


      1. Always place a removed or new curtain shield airbag assembly in a clear plastic bag, and keep it in a safe place.

        CAUTION:

        The plastic bag should be disposed of after use.

        Note

        Never disassemble a curtain shield airbag assembly.

      2. Never measure the resistance of the airbag squib. This may cause the airbag to deploy, which could cause serious injury.

      3. Grease or detergents of any kind should not be applied to the curtain shield airbag assembly.

      4. Store the curtain shield airbag assembly in an area where the ambient temperature is below 93°C (199°F), the humidity is not high and there is no electrical noise.

      5. Before using an electric welder anywhere on the vehicle, disconnect the center airbag sensor assembly connectors. These connectors contain shorting springs. This feature reduces the possibility of the airbag deploying due to current entering the squib wiring.

      6. When disposing of the vehicle or a curtain shield airbag assembly by itself, the airbag should be deployed using SST before disposal. Deploy the airbag in a safe place away from electrical noise.

        Click here

    9. SEAT OUTER BELT ASSEMBLY (SEAT BELT PRETENSIONER)


      1. Never measure the resistance of the seat outer belt assembly. This may cause the pretensioner of the seat outer belt assembly to activate, which could cause serious injury.

      2. Never disassemble the seat outer belt assembly.

      3. Never install the seat outer belt assembly on another vehicle.

      4. Store the seat outer belt assembly in an area where the ambient temperature is below 80°C (176°F), the humidity is not high and there is no electrical noise.

      5. Before using an electric welder anywhere on the vehicle, disconnect the center airbag sensor assembly connectors. These connectors contain shorting springs. This feature reduces the possibility of the airbag deploying due to current entering the squib wiring.

      6. When disposing of the vehicle or a seat outer belt assembly by itself, the seat outer belt assembly should be activated before disposal. Activate the seat outer belt assembly in a safe place away from electrical noise.

        Click here

        for Front Seat: Click here

        for Rear Seat: Click here

      7. As the seat outer belt assembly is hot after being activated, allow some time for it to cool down sufficiently before disposal. Never apply water to cool down the seat outer belt assembly.

      8. Grease, detergents, oil or water should not be applied to the seat outer belt assembly.

    10. CENTER AIRBAG SENSOR ASSEMBLY


      1. Never reuse a center airbag sensor assembly that has been involved in a collision where the SRS has deployed.

      2. The connectors to the center airbag sensor assembly should be connected or disconnected with the sensor installed to the vehicle. If the connectors are connected or disconnected while the center airbag sensor assembly is not installed, the SRS may be activated.

      3. Work must be started at least 90 seconds after the engine switch is turned off and the cable is disconnected from the negative (-) battery terminal, even if only loosening the bolts of the center airbag sensor assembly.

    11. WIRE HARNESS AND CONNECTOR


      1. All of the connectors for this system are a standard yellow color. If an SRS wire harness has an open circuit or a connector is broken, replace it.

  3. ELECTRONIC CONTROL

    B007XI3C01
    *1 Cable
    *2 Negative (-) Battery Terminal

    Note


    • Certain systems need to be initialized after disconnecting and reconnecting the cable to the negative (-) battery terminal.

    • After the engine switch is turned off, the radio receiver assembly records various types of memory and settings. As a result, after turning the engine switch off, make sure to wait at least 60*1 seconds or 90*2 seconds before disconnecting the cable from the negative (-) battery terminal. (for Audio and Visual System)

    • After the engine switch is turned off, the radio receiver assembly records various types of memory and settings. As a result, after turning the engine switch off, make sure to wait at least 60 seconds before disconnecting the cable from the negative (-) battery terminal. (for Navigation System)


    • *1: for 12.3 Inch Display

    • *2: for 8 Inch Display


    1. DISCONNECTING AND RECONNECTING CABLE TO NEGATIVE (-) BATTERY TERMINAL


      1. Before performing work on electronic components, disconnect the cable from the negative (-) battery terminal to prevent damage to the electrical system or components.

      2. When disconnecting the cable, turn the engine switch and headlight switch off and loosen the cable nut completely. Perform these operations without twisting or prying the cable. Then disconnect the cable.

      3. Clock settings, radio settings, audio system memory, DTCs and other data will be cleared when the cable is disconnected from the negative (-) battery terminal. Write down any necessary data before disconnecting the cable.

    2. B007YY5C01
      *a Incorrect

      HANDLING OF ELECTRONIC PARTS


      1. Do not open the cover or case of the ECU unless absolutely necessary. If the IC terminals are touched, the IC may be rendered inoperative by static electricity.

      2. Do not pull on the wires when disconnecting electronic connectors. Pull on the connector itself.

      3. Do not drop electronic components, such as sensors or relays. If they are dropped on a hard surface, they should be replaced.

      4. When cleaning the engine components with steam, protect the electronic components, air filter and emission-related components from water.

      5. Never use an impact wrench to remove or install temperature switches or temperature sensors.

      6. When measuring the resistance between terminals of a wire connector, insert the tester probe carefully to prevent the terminals from bending.

  4. REMOVAL AND INSTALLATION OF FUEL CONTROL PARTS


    1. PLACE FOR REMOVING AND INSTALLING FUEL SYSTEM PARTS


      1. Work in a location with good air ventilation that does not have welders, grinders, drills, electric motors, stoves, or any other ignition sources nearby.

      2. Never work in a pit or near a pit as fuel vapors will collect there.

    2. REMOVING AND INSTALLING FUEL SYSTEM PARTS


      1. Prepare a fire extinguisher before starting work.

      2. To prevent static electricity, install a ground wire between the fuel changer and vehicle, and do not spray the surrounding area with water. Be careful when performing work in this area, as the floor surface will become slippery. Do not clean up gasoline spills with water, as this may cause the gasoline to spread, and possibly create a fire hazard.

      3. Avoid using electric motors, work lights and other electric equipment that can cause sparks or high temperatures.

      4. Avoid using iron hammers as they may create sparks.

      5. Dispose of fuel-contaminated cloth separately using a fire resistant container.

  5. REMOVAL AND INSTALLATION OF ENGINE INTAKE PARTS


    1. B007YHG

      If any metal particles enter intake system parts, they may damage the engine.

    2. When removing and installing intake system parts, cover the openings of the removed parts and engine openings. Use adhesive tape or other suitable materials.

    3. When installing intake system parts, check that no metal particles have entered the engine or installed parts.

  6. HANDLING OF HOSE CLAMPS

    B007YGKC09
    *1 Clamp Track
    *2 Spring Type Clamp

    1. Before removing a hose, check the clamp position so that it can be reinstalled in the same position.

    2. Replace any deformed or dented clamps with new ones.

    3. When reusing a hose, attach the clamp on the clamp track portion of the hose.

    4. For a spring type clamp, it may be necessary to spread the tabs slightly after installation by pushing them in the direction of the arrows as shown in the illustration.

  7. FOR VEHICLES EQUIPPED WITH MOBILE COMMUNICATION SYSTEMS

    B007ZYA

    1. Install the antenna as far away from the ECU and sensors of the vehicle electronic systems as possible.

    2. Install the antenna and feeder at least 20 cm (7.87 in.) away from the ECUs and sensors of the vehicle electronic systems. For details about ECU and sensor locations, refer to the section on the applicable components.

    3. Keep the antenna and feeder separate from other wiring as much as possible. This will prevent signals sent from the communication equipment from affecting vehicle equipment and vice versa.

    4. Check that the antenna and feeder are correctly adjusted.

    5. Do not install a high-powered mobile communication system.

  8. HEADLIGHT INSPECTION OR MAINTENANCE


    1. B00803SC07
      *a Illumination for 3 minutes or more prohibited if covered

      When the headlights are illuminated, do not cover the headlights for 3 minutes or more.

      Note

      As the headlight outer lens is made of resin, the resulting heat created when covering the headlight for an extended period of time may deform the headlight.

  9. FOR ELECTRIC PARKING BRAKE SYSTEM


    1. Precautions when working on vehicle.


      1. When tilting the vehicle to perform work after parking the vehicle on a level surface, the braking force may not be sufficient. Make sure to pull the electric parking brake switch (combination switch assembly) to the lock side 2 times (2 lock operations).

        Tech Tips


        • The electric parking brake system determines the amount of force used to operate the parking brake according to the tilt angle detected by the deceleration sensor (airbag ECU assembly).

        • When the electric parking brake switch (combination switch assembly) is pulled to the lock side 2 times (2 lock operations), the maximum amount of braking force is applied.

      2. PARKING BRAKE FORCED RELEASE METHOD

        For the parking brake forced release method: Click here

  10. FOR VEHICLES EQUIPPED WITH TRACTION CONTROL (TRC) AND VEHICLE STABILITY CONTROL (VSC) SYSTEMS

    When testing with a 2-wheel drum tester such as a speedometer tester, combination tester for the speedometer and brakes, or chassis dynamometer, or when jacking up the front wheels and turning the wheels, perform the following procedure to enter Inspection Mode and disable the TRC and VSC systems.

    Click here

    Note

    Secure the vehicle with lock chains for safety.

    Tech Tips


    • If Inspection Mode is not used, the vehicle may unexpectedly move off the dynamometer because of TRC and VSC operation.

    • The VSC OFF switch (combination switch assembly) must not be used to disable TRC and VSC operation when the vehicle is to be operated on a dynamometer. Pressing the VSC OFF switch (combination switch assembly) does not disable TRC and VSC operation completely.

  11. WHEN SERVICING DYNAMIC TORQUE CONTROL AWD VEHICLES


    1. When using a speedometer tester

      Note


      • The inspection should be performed using the front wheels.

      • Do not exceed a vehicle speed of 60 km/h (37 mph) (when using free rollers to support the front wheels, the vehicle speed must not exceed 50 km/h (31 mph)).

      • The driving time should be less than 1 minute.

      • Follow all usage and safety procedures in the operator's manual of the speedometer tester.


      1. Place the front wheels on the rollers.

      2. Place the rear wheels on rollers or jack up the rear wheels.

      3. Using the GTS, enter Control Mode Change and disable four wheel drive control.

        Note

        If the engine switch is turned off and then turned on (IG) again while in AWD control prohibit mode, AWD control prohibition will be stopped and AWD control normal mode will resume.

      4. Enter Inspection Mode to disable TRC and VSC control.

      5. B00801H

        Secure the vehicle with suitable chains or straps.

      6. Start the engine, and measure the vehicle speed while increasing the speed gradually.

      7. After the test is finished, decrease the speed gradually and stop the vehicle.

    2. When using a brake tester

      Note


      • A high-speed type brake tester cannot be used.

      • Do not exceed a vehicle speed of 0.5 km/h (0.3 mph).

      • Follow all usage and safety procedures in the operator's manual of the brake tester.


      1. Using the GTS, enter AWD Control Prevention Mode Change and disable AWD control.

        Note

        If the engine switch is turned off and then turned on (IG) again while in AWD control prohibit mode, AWD control prohibition will be stopped and AWD control normal mode will resume.

      2. Enter Inspection Mode to disable TRC and VSC control.

      3. Position the wheels to be tested (front or rear) on the tester.

      4. Move the shift lever to N.

      5. Start the engine to allow normal brake booster operation.

      6. Operate the brakes to perform the test.

    3. When using a chassis dynamometer


      1. Place the front wheels on the rollers or jack up the front wheels.

      2. Using the GTS, enter AWD Control Prevention Mode Change and disable AWD control.

      3. Enter Inspection Mode to disable TRC and VSC control.

      4. Remove the propeller shaft if necessary as shown in the illustration.

        Note


        • Do not brake or accelerate suddenly.

        • Confirm that the vehicle is secure.

        • Follow all usage and safety procedures in the operator's manual of the chassis dynamometer.

        • Make sure to remove the propeller shaft if necessary as shown in the illustration. Failure to do so may damage components of the AWD system and increase the risk of the vehicle jumping off the dynamometer.

        B007X5XC01
        *1 Propeller shaft - -
        *a Two-wheel chassis dynamometer *b Four-wheel chassis dynamometer (directly-connected)
        *c Four-wheel chassis dynamometer (except directly-connected) - -
        B007WXX Remove - -
    4. When using an on-vehicle wheel balancer


      1. Raise the vehicle until all 4 wheels are off the ground.

      2. Support the vehicle with safety stands at an appropriate height. Make sure that the vehicle does not lean in any direction, and that the tires are completely clear of the floor.

      3. Place the vibration pick-up unit into position for the wheel to be measured*1.

      4. Release the parking brake.

      5. Check that each wheel turns freely when turning them by hand.

      6. Put the wheel balancer in position.

      7. Wheel balance measurement should be done by using both the engine and the wheel balancer drive roller to spin the wheels.

        Tech Tips

        *1: Different on-vehicle wheel balancers have different requirements for mounting the vibration pick-up unit(s). Refer to the operator's manual of the wheel balancer to confirm requirements for use.

        Note


        • Be sure to perform measurement the test in Inspection Mode.

        • Start the engine and then increase the vehicle speed gradually with the shift lever in D.

        • Do not accelerate or decelerate suddenly.

        • Deceleration should be done by braking gradually.

        • Make sure that no one is standing in-line with the spinning wheels.

        • Measurement should be done quickly.

        • Confirm that the vehicle is secure.

        • Follow all usage and safety procedures in the operator's manual of the wheel balancer.

  12. PRECAUTIONS FOR TOWING FRONT WHEEL DRIVE VEHICLES


    1. Use one of the following methods to tow the vehicle.

    2. If the vehicle has trouble with the chassis or drivetrain, use method 1 (flatbed truck).

      B007WYCE34

      Note


      • Do not use any towing method other than those shown above.

      • If the vehicle is tilted after parking on a level surface, the braking force may be insufficient as the electric parking brake determines how much braking force to apply by automatically detecting the slope of the road.

        When the electric parking brake switch (integration control and panel assembly) is pulled 2 times (2 lock operations), the system uses the maximum amount of braking force.

    3. If a tow truck is not available, in an emergency the vehicle may be temporarily towed using a cable or chain secured to the emergency towing eyelet(s). This should only be attempted on hard surfaced roads for distances of less than 80 km (50 miles), and at speeds below 30 km/h (18 mph).

      A driver must be in the vehicle to steer and operate the brakes. The vehicle's wheels, drivetrain, axles, steering and brakes must be in good condition.

      Note

      If the towing speed or distance exceeds the specified limits, or the vehicle is towed in a backward direction with the front wheels on the ground, the drivetrain or vehicle may be damaged.


      1. Emergency towing procedure


        1. Turn the engine switch on (IG).

        2. Depress the brake pedal and move the shift lever to N.

        3. Release the parking brake.

        4. Release the brake pedal slowly.

        Note


        • Use extreme caution when towing the vehicle. Avoid sudden starts or erratic driving maneuvers which place excessive stress on the emergency towing eyelet and the cables or chains.

        • Do not turn off the engine switch. Turning off the engine switch may result in engagement of the steering lock, resulting in a hazardous situation or accident.

    4. The towing methods shown below are dangerous and can damage the vehicle, so do not use them.

      B007Z3H

      1. Do not tow the vehicle facing rearward with the front wheels on the ground.

        Note


        • If the vehicle is towed facing rearward with the front wheels on the ground, the drivetrain may overheat and be damaged.

        • In addition, if the vehicle is equipped with a VSC system, the system may apply the brakes to the rotating wheels.

      2. Do not use a sling-type towing method either from the front or rear.

        Note

        If a sling-type tow truck is used, damage may occur to the vehicle body.

  13. PRECAUTIONS FOR TOWING ALL WHEEL DRIVE VEHICLES


    1. Use one of the following methods to tow the vehicle.

    2. If the vehicle has trouble with the chassis or drivetrain, use method 1 (flatbed truck).

      B00801YE10

      Note


      • Do not use any towing method other than those shown above.

      • If the vehicle is tilted after parking on a level surface, the braking force may be insufficient as the electric parking brake determines how much braking force to apply by automatically detecting the slope of the road.

        When the electric parking brake switch (integration control and panel assembly) is pulled 2 times (2 lock operations), the system uses the maximum amount of braking force.

    3. If a tow truck is not available, in an emergency the vehicle may be temporarily towed using a cable or chain secured to the emergency towing eyelet(s). This should only be attempted on hard surfaced roads for distances of less than 80 km (50 miles), and at speeds below 30 km/h (18 mph).

      A driver must be in the vehicle to steer and operate the brakes. The vehicle's wheels, drivetrain, axles, steering and brakes must be in good condition.

      Note

      If the towing speed or distance exceeds the specified limits, or the vehicle is towed in a backward direction with any of the wheels on the ground, the drivetrain or vehicle may be damaged.


      1. Emergency towing procedure


        1. Turn the engine switch on (IG).

        2. Depress the brake pedal and move the shift lever to N.

        3. Release the parking brake.

        4. Release the brake pedal slowly.

        Note


        • Use extreme caution when towing the vehicle. Avoid sudden starts or erratic driving maneuvers which place excessive stress on the emergency towing eyelet and the cables or chains.

        • Do not turn off the engine switch. Turning off the engine switch may result in engagement of the steering lock, resulting in a hazardous situation or accident.

    4. The towing methods shown below are dangerous and can damage the vehicle, so do not use them.

      B00800O

      1. Do not tow the vehicle with the front or rear wheels on the ground.

        Note


        • If the vehicle is towed with the front or rear wheels on the ground, the drivetrain may overheat and be damaged.

        • As the vehicle is equipped with a VSC system, if the vehicle is towed with the front or rear wheels on the ground, the system may apply the brakes to the rotating wheels.

      2. Do not use a sling-type towing method either from the front or rear.

        Note

        If a sling-type tow truck is used, damage may occur to the vehicle body.

  14. PRECAUTIONS FOR TOWING VEHICLES EQUIPPED WITH STOP AND START SYSTEM

    Note


    • When towing the vehicle, the front wheels or all 4 wheels must be lifted.

    • If the vehicle is towed with all 4 wheels on the ground, components of the stop and start system may be damaged.

  15. WARNING NOTIFICATION FUNCTION (VEHICLES WITH G-BOOK SERVICE CONTRACT*1)

    *1: w/ Telematics Transceiver

    Note


    • Before performing inspections or repairs which may cause warning messages to be displayed or DTCs to be stored, such as a simulation test or road test, it is necessary to activate warning notification restraint mode so that the G-BOOK center does not recognize the warnings as real ones.

    • Warning notification restraint mode can be entered by using the GTS or operating the remote touch.

    Tech Tips

    The warning notification function sends a warning on signal, received from the combination meter assembly via CAN communication, to the G-BOOK center using the G-BOOK device if a warning message is displayed due to a malfunction.


    1. Activate warning notification restraint mode

      Tech Tips

      To cancel warning notification restraint mode, turn the engine switch off and on (IG) to display the service mode screen and cancel warning notification restraint mode.


      1. Activate warning notification restraint mode (Using the GTS)


        1. Connect the GTS to the DLC3.

        2. Start the engine.

        3. Turn the GTS on.

        4. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

      2. Activate warning notification restraint mode (Using the remote touch)


        1. Enter navigation system diagnostic mode.

          Click here

  16. STRICT PROHIBITION OF MANUAL EMERGENCY CALL USING EMERGENCY CALL SERVICE (VEHICLES WITH G-BOOK SERVICE CONTRACT*1)

    *1: w/ Telematics Transceiver


    1. Do not make emergency calls in non-emergency situations. When performing an inspection, use the manual maintenance check.

      Note


      • If the emergency call service is used to connect to the G-BOOK center in a non-emergency situation, an unnecessary workload will be generated at the G-BOOK center. This may cause a delayed response by the G-BOOK center to other emergency calls.

      • If emergency vehicles are dispatched due to an accidental operation of the emergency call switch, you may be charged or punished according to local law.

    2. If the emergency call switch is accidentally operated:


      1. Contact the G-BOOK center to tell them that the call was made by mistake.

      2. An emergency call cannot be halted or finished from the vehicle. Only the G-BOOK center can halt or finish an emergency call.

      3. If the G-BOOK center cannot be informed that the emergency call was made by mistake, the center will report an emergency to authorities, emergency facilities and dealerships in compliance with its agreements. As a result, emergency vehicles may be dispatched.

  17. ALARM NOTIFICATION FUNCTION (VEHICLES WITH G-BOOK SERVICE CONTRACT*1)

    *1: w/ Telematics Transceiver


    1. If the theft deterrent system is activated, the G-BOOK center makes a phone call to the customer.

      Note


      • When servicing the vehicle, make sure that the vehicle does not experience any conditions that could cause a telephone call to be made by a G-BOOK operator.

      • Before performing inspections or repairs which may activate the alarm notification function, be sure to inform the customer that they may receive a telephone call from a G-BOOK operator.

      Tech Tips

      The alarm notifications can be canceled on the multi-display screen.

  18. FOR VEHICLES EQUIPPED WITH CATALYTIC CONVERTER

    CAUTION:

    If a large amount of unburned gasoline or gasoline vapors flow into the converter, it may cause converter overheating and create a fire hazard. To prevent this, observe the following precautions:


    1. Use only unleaded gasoline.

    2. Avoid performing unnecessary spark tests.


      1. Perform a spark test only when absolutely necessary. Perform this test as rapidly as possible.

      2. While testing, never race the engine unless instructed.

    3. Avoid a prolonged engine compression measurement. Engine compression measurements must be performed as rapidly as possible.

    4. Do not run the engine when the fuel tank is nearly empty. This may cause the engine to misfire and create an extra load on the converter.

  19. INSPECTION AND ADJUSTMENT OF JOINT ANGLE DURING REMOVAL AND INSTALLATION OF PROPELLER SHAFT


    1. When performing operations which involve the removal and installation of the propeller shaft, always check the joint angle. Make adjustments if necessary.

      Click here

      B007YMTC01
      *a No. 1 Joint Angle *b No. 4 Joint Angle