СТАРТЕР (для моделей мощностью 1,6 кВт) ПОВТОРНАЯ СБОРКА


  1. INSTALL STARTER CENTER BEARING CLUTCH SUB-ASSEMBLY


    1. A01E1W8E01
      Text in Illustration
      *1 Starter Drive Pinion Lever
      *2 Rubber Plate
      *3 Starter Center Bearing Clutch Sub-assembly
      A01E2TX High-temperature Grease

      Apply high-temperature grease to the starter pinion drive lever as shown in the illustration.

    2. Install the starter center bearing clutch sub-assembly, rubber plate and starter pinion drive lever to the starter drive housing assembly.

    3. A01E1A3

      Apply high-temperature grease to the planetary gears and pins of the starter center bearing clutch sub-assembly as shown in the illustration.

      Text in Illustration
      A01E2TX High-temperature Grease

    4. Install the 3 planetary gears to the starter center bearing clutch sub-assembly.

  2. INSTALL STARTER ARMATURE ASSEMBLY


    1. Install the starter armature assembly to the starter yoke assembly.

      Note

      The magnet of the starter yoke may attract the starter armature when the starter commutator end frame is installed, causing the magnet to break.

  3. INSTALL STARTER BRUSH HOLDER ASSEMBLY


    1. Install the starter brush holder assembly to the starter yoke assembly.

    2. A01DYOZ

      Connect the 4 brushes to the starter brush holder assembly.


      1. Using a screwdriver, hold back the spring.

      2. Connect the brush to the brush holder assembly.

    3. A01DXF1E02
      Text in Illustration
      *1 Grommet
      *2 Motor Lead Line Positive (+) Side
      *3 Brush Holder Plate Negative (-) Side

      Insert a grommet between the positive (+) side of the motor lead line and the negative (-) side of the brush holder plate.

    4. A01DZ3VE01
      Text in Illustration
      *1 Rubber Part
      *2 Starter Commutator End Frame Assembly

      Align the rubber part of the starter yoke assembly with the groove of the starter commutator end frame assembly.

    5. Install the starter commutator end frame assembly with the 2 screws.

      Torque:
      1.5 N*m  { 15 kgf*cm, 13 in.*lbf }

  4. INSTALL STARTER YOKE ASSEMBLY


    1. Install the starter armature plate to the starter yoke assembly.

    2. A01DV6GE01
      Text in Illustration
      *1 Protrusion
      *2 Notch

      Check that the notch of the starter armature plate fits over the protrusion of the starter yoke assembly.

    3. A01DWP1E01
      Text in Illustration
      *1 Notch
      *2 Protrusion

      Align the protrusion of the starter yoke assembly with the notches inside the starter drive housing assembly and insert the starter yoke assembly into the starter drive housing assembly.

    4. Using a T25 "TORX" socket wrench, install the starter drive housing assembly with the 2 through bolts.

      Torque:
      6.0 N*m  { 61 kgf*cm, 53 in.*lbf }

  5. INSTALL MAGNET STARTER SWITCH ASSEMBLY


    1. Apply high-temperature grease to the plunger hook of the magnet starter switch assembly.

    2. A01DXTT

      Hang the plunger of the magnet starter switch assembly on the starter pinion drive lever from the upper side.

    3. Install the magnet starter switch assembly with the 2 nuts.

      Torque:
      7.5 N*m  { 76 kgf*cm, 66 in.*lbf }

    4. Connect the lead wire to terminal C with the nut.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }