SEAT BELT WARNING SYSTEM(w/o Occupant Classification System) Driver Side Seat Belt Warning Light does not Operate

DESCRIPTION

The combination meter assembly illuminates, blinks or turns off the seat belt warning light on the combination meter assembly in accordance with the state of the front seat inner belt assembly (driver seat).

WIRING DIAGRAM

B008JJZE26

CAUTION / NOTICE / HINT

Note


  • The seat belt warning system uses the CAN communication system. First, confirm that there is no malfunction in the CAN communication system. Refer to the How to Proceed with Troubleshooting procedure.

    Click here

  • Before replacing the main body ECU (multiplex network body ECU), refer to the Service Bulletin.

  • As the door control battery is installed between the vehicle battery and main body ECU (multiplex network body ECU), first perform the inspections in On-Vehicle Inspection to confirm that there are no malfunctions in the power source circuit for the main body ECU (multiplex network body ECU) before performing this troubleshooting procedure.*

    *: w/ Door Control Battery

    Click here

  • When replacing the combination meter assembly, make sure to replace it with a new one.

  • After replacing the airbag ECU assembly, refer to initialization.

    Click here

PROCEDURE


  1. CHECK DTC OUTPUT (AIRBAG SYSTEM)


    1. Clear DTCs.

      Click here


      Body Electrical > SRS Airbag > Clear DTCs

    2. Check for DTCs.

      Click here


      Body Electrical > SRS Airbag > Trouble Codes
      OK
      DTCs are not output.
      Result
      Proceed to
      OK
      NG

    NG

    GO TO AIRBAG SYSTEM Click here

    OK

  2. READ VALUE USING GTS (Left side Buckle SW, Right side Buckle SW)


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / SRS Airbag / Data List.

    5. Read the Data List according to the display on the GTS.


      Body Electrical > SRS Airbag > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Left side Buckle SW LH buckle switch*1 Unset, Set or NG

      Unset: Seat belt not fastened

      Set: Seat belt fastened

      NG: Data is not determined

      		 -
      Right side Buckle SW RH buckle switch*2 Unset, Set or NG

      Unset: Seat belt not fastened

      Set: Seat belt fastened

      NG: Data is not determined

      		 -

      • *1: for LHD

      • *2: for RHD


      Body Electrical > SRS Airbag > Data List
      Tester Display
      Left side Buckle SW
      Right side Buckle SW
      Result
      Result Proceed to
      Unset or Set is displayed correctly on the GTS screen according to the driver side belt condition A
      Unset or Set is not displayed correctly on the GTS screen according to the driver side belt condition B
      NG is displayed on the GTS screen C

    B

    REPLACE FRONT SEAT INNER BELT ASSEMBLY (for Driver Side) for Power Seat: Click here for Manual Seat: Click here

    C

    REPLACE AIRBAG ECU ASSEMBLY Click here

    A

  3. REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)


    1. Temporarily replace the main body ECU (multiplex network body ECU) with a new one.


      Result
      Proceed to
      NEXT

    NEXT

  4. CHECK SEAT BELT WARNING LIGHT


    1. Check the operation of the seat belt warning light.

      Click here

      OK
      The seat belt warning light operates normally.
      Result
      Proceed to
      OK
      NG

    OK

    END (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] WAS DEFECTIVE)

    NG

    REPLACE COMBINATION METER ASSEMBLY Click here