TIRE AND WHEEL SYSTEM INSPECTION

PROCEDURE

  1. INSPECT TIRES

    1. Check the tires for wear and proper inflation pressure.

      Cold Tire Inflation Pressure

      Tire Size

      Engine Type

      Front

      Rear

      195/65R15 91H

      215/45R17 87W

      1ND-TV*3

      260 kPa (2.6 kgf/cm2, 38 psi)*1

      230 kPa (2.3 kgf/cm2, 33 psi)*2

      270 kPa (2.7 kgf/cm2, 39 psi)*4

      260 kPa (2.6 kgf/cm2, 38 psi)*1

      230 kPa (2.3 kgf/cm2, 33 psi)*2

      260 kPa (2.6 kgf/cm2, 38 psi)*4

      Others

      260 kPa (2.6 kgf/cm2, 38 psi)*1

      230 kPa (2.3 kgf/cm2, 33 psi)*2

      205/55R16 91V

      225/45R17 91W

      1AD-FTV

      270 kPa (2.7 kgf/cm2, 39 psi)*1

      240 kPa (2.4 kgf/cm2, 35 psi)*2

      260 kPa (2.6 kgf/cm2, 38 psi)*1

      230 kPa (2.3 kgf/cm2, 33 psi)*2

      Others

      260 kPa (2.6 kgf/cm2, 38 psi)*1

      230 kPa (2.3 kgf/cm2, 33 psi)*2

      *1: For driving at over 160 km/h (100 mph)

      *2: For driving at under 160 km/h (100 mph)

      *3: with ECO tire pressure label

      *4: ECO pressure (for driving at under 160 km/h (100 mph))

    2. C137874

      Using a dial indicator, check the runout of the tires.

      Maximum tire runout

      1.4 mm (0.0551 in.)

  2. ROTATE TIRES

    1. C142114C01
      V100135

      Front

      If the spare tire uses a different type of wheel from the other tires, rotate the tires as shown by (A) in the illustration. If the spare tire has the same type of wheel as the other tires, rotate the tires, including the spare tire, as shown by (B) in the illustration.

      103 N*m

      1050 kgf*cm

      76 ft.*lbf

  3. INSPECT AND ADJUST WHEEL BALANCE

    1. Inspect and adjust the off-the-car balance.

      1. Steel wheel:

        Maximum imbalance

        8.0 g (0.0176 lb)

      2. C144018N02

        Others (Non-steel wheel):

        Maximum imbalance

        8.0 g (0.0176 lb)

        Note:

        • Adhere a stick-on type balance weight to the flat surface (A) shown in the illustration.

          Width (A)

          25 mm (0.984 in.)

        • Use a cleaning detergent to remove dirt, oil and water from the surface where the balance weight is to be adhered.

        • Do not touch the adhesive surface of the balance weight.

        • Push the balance weight with your finger to securely adhere it to the desired position.

        • Do not reuse balance weights.

        Tip:

        The inner side balance weight should be installed by clipping it to the rim.

  4. INSPECT FRONT AXLE HUB

    Click here

  5. INSPECT REAR AXLE HUB

    for Double Wishbone Type Suspension:Click here

    for Torsion Beam Type Suspension:Click hereClick here