АВТОМАТИЧЕСКАЯ ТРАНСМИССИЯ В СБОРЕ СНЯТИЕ


  1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.

  2. REMOVE ENGINE UNDER COVER

  3. REMOVE NO. 1 ENGINE UNDER COVER

  4. REMOVE NO. 2 FRAME CROSSMEMBER SUB-ASSEMBLY

    A01E028E01

    1. Remove the 4 nuts, 4 bolts and frame crossmember.

  5. REMOVE FRONT EXHAUST PIPE ASSEMBLY


    1. Remove the front exhaust pipe Click here.

  6. REMOVE PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY


    1. Remove the propeller with center bearing shaft assembly Click here.

  7. DRAIN AUTOMATIC TRANSMISSION FLUID


    1. Remove the drain plug and gasket, and drain the ATF.

    2. Install a new gasket and the drain plug.

      Torque:
      20 N*m  { 205 kgf*cm, 15 ft.*lbf }

  8. REMOVE TRANSMISSION OIL FILLER TUBE SUB-ASSEMBLY

    A01DYZ6

    1. Remove the oil dipstick.

    2. Remove the 2 bolts and oil filler tube.

    3. Remove the O-ring from the oil filler tube.

  9. DISCONNECT OIL COOLER TUBE

    A01E0I3

    1. Using a union nut wrench, disconnect the tube outlet and tube inlet.

    2. A01DV4M

      Remove the 3 bolts and 3 clamps.

  10. DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

    A01DZUZE01

    1. Remove the nut and disconnect the control cable.

    2. Remove the clip and disconnect the control cable.

  11. REMOVE STARTER ASSEMBLY


    1. for 1.4 kW Type:

      Remove the starter Click here.

    2. for 1.6 kW Type:

      Remove the starter Click here.

  12. SUPPORT AUTOMATIC TRANSMISSION ASSEMBLY

    A01E2VJE01

    1. Support the transmission with a transmission jack.

  13. REMOVE NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY


    1. A01DZEX

      Detach the wire harness clamp from the No. 3 frame crossmember.

    2. A01E24Y

      Remove the 4 set bolts of the rear No. 1 engine mounting insulator.

    3. Remove the 4 nuts, 4 bolts and frame crossmember.

  14. REMOVE NO. 1 ENGINE MOUNTING INSULATOR REAR

    A01E1RJ

    1. Remove the 4 bolts, ground cable and engine mounting insulator.

  15. DISCONNECT CONNECTOR


    1. A01DZU9

      Remove the 2 bolts and heat insulator.

    2. A01E1UUE01

      Tilt the transmission downward.

      Note

      Make sure the cooling fan does not contact the fan shroud.

    3. Disconnect the park/neutral position switch connector, transmission wire connector, ATF temperature sensor connector and 3 speed sensor connectors.

    4. Disconnect the 4 wire harness clamps.

  16. REMOVE FLYWHEEL HOUSING DUST SEAL


    1. Remove the flywheel housing dust seal.

  17. REMOVE AUTOMATIC TRANSMISSION ASSEMBLY


    1. A01DWBN

      Turn the crankshaft to gain access to each bolt.

    2. Hold the crankshaft pulley bolt with a wrench and remove the 6 torque converter clutch mounting bolts.

    3. A01DZ1C

      Remove the 3 bolts and exhaust manifold stay.

    4. A01DUXS

      Remove the 7 bolts.

    5. Separate the transmission from the engine.

  18. REMOVE TORQUE CONVERTER CLUTCH ASSEMBLY


    1. Remove the torque converter from the automatic transmission assembly.

  19. REMOVE TRANSMISSION CONTROL CABLE BRACKET


    1. A01E29NE01

      Remove the 2 bolts and control cable bracket from the transmission.