POWER DOOR LOCK CONTROL SYSTEM

CAUTION / NOTICE / HINT

PROCEDURE

1. VEHICLE BROUGHT TO WORKSHOP

   Result

   Proceed to
   NEXT

   NEXT

2. CUSTOMER PROBLEM ANALYSIS CHECK

   Tip:

   • In troubleshooting, confirm that the problem symptoms have been accurately identified. Preconceptions should be discarded in order to make an accurate judgment. To clearly understand what the problem symptoms are, it is extremely important to ask the customer about the problem and the conditions at the time the malfunction occurred.

   • Gather as much information as possible for reference. Past problems that seem unrelated may also help in some cases.

   • The following 5 items are important points for problem analysis:

   What	Vehicle model, system name
   When	Date, time, occurrence frequency, whether the problem occurred recently or has been occurring for a long time
   Where	Whether the problem occurs at a specific location
   Under what conditions?	Whether the doors were locked or unlocked, whether the power switch was on (IG), whether the engine has started
   How did it happen?	Problem symptoms

   Result

   Proceed to
   NEXT

   NEXT

3. INSPECT AUXILIARY BATTERY VOLTAGE

   1. Measure the auxiliary battery voltage.

      Standard voltage

      11 to 14 V (power switch off)

      If the voltage is below 11 V, recharge or replace the auxiliary battery before proceeding to the next step.

   2. Check the fuses and relays.

   3. Check the connector connections and terminals to make sure that there are no abnormalities such as loose connections, deformation, etc.

   Result

   Proceed to
   NEXT

   NEXT

4. INSPECT COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM*

   1. Using the GTS, check for CAN communication system DTCs.

      for LHD:Click hereClick hereClick here

      for RHD:Click hereClick hereClick here

   Result

   Proceed to
   CAN DTCs are not output
   CAN DTCs are output (for LHD)
   CAN DTCs are output (for RHD)

   CAN DTCs are output (for LHD)

   GO TO CAN COMMUNICATION SYSTEM

   Click hereClick here

   CAN DTCs are output (for RHD)

   GO TO CAN COMMUNICATION SYSTEM

   Click hereClick here

   CAN DTCs are not output

5. INSPECT COMMUNICATION FUNCTION OF LIN COMMUNICATION SYSTEM*

   1. Using the GTS, check for LIN communication system DTCs.

      Click here

   Result

   Proceed to
   LIN DTCs are not output
   LIN DTCs are output

   LIN DTCs are output

   GO TO LIN COMMUNICATION SYSTEM

   Click here

   LIN DTCs are not output

6. CHECK FOR DTC (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY)*

   1. Clear the DTCs.

      Click here

      Body Electrical > Master Switch > Clear DTCs

   2. Recheck for DTCs.

      Click here

      Body Electrical > Master Switch > Trouble Codes

   Result

   Proceed to
   DTC B2312 is not output
   DTC B2312 is output

   DTC B2312 is output

   GO TO POWER WINDOW CONTROL SYSTEM

   Click here

   DTC B2312 is not output

7. PROBLEM SYMPTOMS TABLE

   1. Refer to Problem Symptoms Table.

      Click hereClick here

   Result

   Proceed to
   Fault is not listed in Problem Symptoms Table
   Fault is listed in Problem Symptoms Table

   Fault is listed in Problem Symptoms Table

   ADJUST, REPAIR OR REPLACE IN ACCORDANCE WITH PROBLEM SYMPTOMS TABLE

   Fault is not listed in Problem Symptoms Table

8. OVERALL ANALYSIS AND TROUBLESHOOTING*

   1. Terminals of ECU

      Click here

   2. Data List / Active Test

      Click here

   3. Operation Check

      Click hereClick here

   Result

   Proceed to
   NEXT

   NEXT

9. REPAIR OR REPLACE

   Result

   Proceed to
   NEXT

   NEXT

10. CONFIRMATION TEST

    Result

    Proceed to
    NEXT

    NEXT

    END