TRANSMISSION CONTROL CABLE INSTALLATION

PROCEDURE

1. INSTALL TRANSMISSION CONTROL CABLE ASSEMBLY

   
   

   1. 

      Pass the transmission control cable assembly into the vehicle and install the transmission control cable assembly to the vehicle body with the 2 nuts.

      Torque:

      5.0 N*m  { 51 kgf*cm, 44 in.*lbf }

   2. 

      Engage the guide to connect the transmission control cable assembly to vehicle body.

   3. Install the nut.

      Torque:

      5.0 N*m  { 51 kgf*cm, 44 in.*lbf }

   4. 

      Turn the control shaft lever clockwise until it stops, and then from that position turn it counterclockwise by 2 notches to set it to the N position.

   5. Connect the transmission control cable assembly to the No. 1 transmission control cable bracket with a new clip.

   6. Connect the transmission control cable assembly to the control shaft lever with the nut.

      Torque:

      12 N*m  { 122 kgf*cm, 9 ft.*lbf }

   7. for TMMT Made:

      
      

      1. 

         Install in this Direction

         Connect the transmission control cable assembly to the floor shift shift lever assembly.

         Note

         Make sure that the transmission control cable assembly is securely locked.

      2. 

         Install in this Direction

         Connect the end of the transmission control cable assembly to the floor shift shift lever assembly.

         Note

         
         

         • Before connecting the transmission control cable assembly, check that the park/neutral position switch and shift lever are in N.

         • Install the end of the transmission control cable assembly so that the lock piece faces the driver side.

         • Install the end of the transmission control cable assembly all the way to the base of the pin.

   8. for TMC Made:

      
      

      1. 

         *1	Nut
         *2	Lock
         	Rotate approximately 180°
         	Push in

         Rotate the nut of the transmission control cable assembly approximately 180° in the direction shown in the illustration, and while holding the nut in that position, push in the lock.

         Note

         Rotating the nut too much will damage the internal spring, and the transmission control cable assembly will not be reusable. Do not turn the nut too far.

      2. 

         *1	Lock
         *a	Protrusion
         	Install in this Direction

         Install the transmission control cable assembly to the floor shift shift lever assembly.

         Note

         
         

         • Install the transmission control cable assembly with the protrusion facing upwards.

         • After installation, make sure that the lock is projecting from A as shown in the illustration.

         • Make sure that the transmission control cable assembly is securely locked.

      3. 

         Install in this Direction

         Confirm that the shift lever is in N, and then connect the end of the transmission control cable assembly to the floor shift shift lever assembly.

         Note

         
         

         • Securely install the end of the transmission control cable assembly to the floor shift shift lever assembly.

         • Install the end of the transmission control cable assembly so that its adjustment lock section is on the driver side.

2. ADJUST SHIFT LEVER POSITION

   Click here

3. INSTALL FRONT NO. 1 FLOOR HEAT INSULATOR

   
   

   1. Install the front No. 1 floor heat insulator to the vehicle body with the 2 bolts and nut.

      Torque:

      5.0 N*m  { 51 kgf*cm, 44 in.*lbf }

4. INSTALL FRONT EXHAUST PIPE ASSEMBLY

   Click here

5. INSTALL NO. 2 CENTER EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst)

   Click here

6. INSTALL FRONT FLOOR CENTER BRACE

   Click here

7. INSTALL BATTERY CLAMP SUB-ASSEMBLY

   Click here

8. INSTALL ECM

   Click here

9. INSTALL AIR CLEANER CASE SUB-ASSEMBLY

   Click here

10. INSTALL AIR CLEANER CAP SUB-ASSEMBLY

    Click here

11. INSTALL NO. 1 AIR CLEANER INLET

    Click here

12. INSTALL RADIATOR COVER

    Click here

13. INSTALL REAR CONSOLE BOX ASSEMBLY

    Click here

14. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY

    Click here

15. INSTALL BATTERY

    Click here

16. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Click here

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

17. INSPECT SHIFT LEVER POSITION

    Click here

18. INSPECT FOR EXHAUST GAS LEAK

    Click here

    Tech Tips

    Perform "Inspection After Repairs" after repairing or replacing the exhaust system.

    Click here