CENTER AIRBAG SENSOR ASSEMBLY REMOVAL

  1. REMOVE LOWER NO. 2 INSTRUMENT PANEL AIRBAG ASSEMBLY

    Click here

  2. REMOVE REAR CONSOLE BOX ASSEMBLY

    Click here

  3. REMOVE FRONT DOOR SCUFF PLATE LH

    1. Disengage the 10 claws and remove the front door scuff plate LH.

      A011XE7

  4. REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH

    1. Remove the clip.

      A011XOP

    2. Pull the cowl side trim sub-assembly LH in the direction indicated by the arrow shown in the illustration to disengage the 2 clips and remove the cowl side trim sub-assembly LH.

  5. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH

    1. Disconnect the front door opening trim weatherstrip LH.

      A011Y5J

  6. REMOVE INSTRUMENT SIDE PANEL LH

    1. Using a moulding remover, disengage the 4 claws as shown in the illustration.

      A011XLO

    2. Disengage the 3 guides and remove the instrument side panel LH as shown in the illustration.

      A011YUQ

  7. DISCONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY

    1. Disengage the claw and 2 guides to disconnect the hood lock control lever sub-assembly.

      A011Y3J

  8. REMOVE LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL ASSEMBLY

    1. Remove the bolt <C> and screw <D> or <E>.

      A011XNW

    2. Disengage the 4 claws, 9 clips and 3 guides to remove the lower No. 1 instrument panel finish panel assembly.

      A011VRM

  9. REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY

    1. Remove the 2 screws <D> or <E>.

      A011XAK

    2. Open the lower instrument panel door.

    3. Remove the 3 screws <D> or <E>.

      A011WAA

    4. Disengage the 2 clips and 3 guides.

      A011X2U

    5. Disengage the glove compartment light as shown in the illustration.

      A011Z0E

    6. Disconnect each connector and remove the lower instrument panel sub-assembly.

  10. REMOVE BOX BOTTOM MAT

    1. Remove the box bottom mat.

      A011WK9

  11. REMOVE UPPER CONSOLE PANEL SUB-ASSEMBLY

    1. Remove the 2 screws <D> or <E>.

      A011YQW

    2. Disengage the 4 clips and guide as shown in the illustration.

      A011XTM

    3. Disconnect each connector to remove the upper console panel sub-assembly.

  12. REMOVE FRONT NO. 2 CONSOLE BOX INSERT

    1. Disengage the 2 claws to disconnect the room temperature sensor from the front No. 2 console box insert.

      A011Z6M

    2. Remove the 2 screws <D> or <E>.

      A011VTG

    3. Disengage the clip and 3 guides to remove the front No. 2 console box insert as shown in the illustration.

      A011YJ4

  13. REMOVE CONSOLE BOX INSERT

    1. Remove the 2 screws <D> or <E>.

      A011XYA

    2. Disengage the clip and 3 guides to remove the console box insert as shown in the illustration.

      A011YOQ

  14. REMOVE FLOOR CARPET BRACKET LH

    1. Remove the 2 clips.

      A011YCB

    2. Disengage the 2 guides to remove the floor carpet bracket LH.

  15. REMOVE FLOOR CARPET BRACKET RH

    1. Remove the 2 clips.

      A011Y2Y

    2. Disengage the 2 guides to remove the floor carpet bracket RH.

  16. REMOVE NO. 1 CONSOLE BOX DUCT (w/ Rear Register Duct)

    1. Remove the clip and the No. 1 console box duct.

      A011XIH

  17. REMOVE AIRBAG SENSOR ASSEMBLY

    1. Check that the power switch is off.

    2. Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    3. Turn back the carpet.

    4. Disconnect the connectors from the airbag sensor assembly as shown in the illustration.

      A011XKX

      Note

      When disconnecting any airbag connector, take care not to damage the airbag wire harness.

    5. Remove the 3 bolts and airbag sensor assembly.