HARD DISK DRIVE REMOVAL

  1. PRECAUTION

    Note

    • After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work Click here.

    • for Navigation Receiver Type:

      • A Hard Disk Drive (HDD) is built into the navigation receiver assembly to store map and other data, and is used for the navigation system. Therefore, care must be taken for the following points when handling the navigation receiver assembly.

    • for Radio and Display Type with Intuitive Parking Assist System:

      • A Hard Disk Drive (HDD) is built into the navigation receiver assembly to store multi-media data, and is used for the audio and visual system. Therefore, care must be taken for the following points when handling the navigation receiver assembly.

    • When removing the hard disk drive, eliminate static electricity by touching the vehicle body to prevent components from being damaged.

  2. REMOVE LUGGAGE TRIM SERVICE HOLE COVER

    1. Disengage the claw to remove the luggage trim service hole cover.

      A011YZM

  3. DISCONNECT CABLE FROM AUXILIARY BATTERY NEGATIVE TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  4. REMOVE REAR CONSOLE BOX ASSEMBLY

    Click here

  5. REMOVE BOX BOTTOM MAT

    1. Remove the box bottom mat.

      A011WK9

  6. REMOVE UPPER CONSOLE PANEL SUB-ASSEMBLY

    1. Remove the 2 screws <D> or <E>.

      A011YQW

    2. Disengage the 4 clips and guide as shown in the illustration.

      A011XTM

    3. Disconnect each connector to remove the upper console panel sub-assembly.

  7. REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY

    1. Using a moulding remover, disengage the 2 claws and 2 clips as shown in the illustration.

      A011YA5

    2. Using a moulding remover, disengage the 2 claws and 2 clips as shown in the illustration.

      A011YX8

    3. Disengage the 3 claws and 2 clips as shown in the illustration.

      A011W28

    4. Disengage the clamp.

      A011XD5

    5. Disconnect the connector to remove the center instrument cluster finish panel assembly.

  8. REMOVE NO. 2 INSTRUMENT PANEL REGISTER ASSEMBLY

    1. Pull the No. 2 instrument panel register assembly in the direction indicated by the arrow to disengage the 6 clips to remove the No. 2 instrument panel register assembly.

      A011XE5

  9. REMOVE NAVIGATION RECEIVER ASSEMBLY WITH AIR CONDITIONING CONTROL ASSEMBLY (for Navigation Receiver Type)

    1. Apply protective tape to the areas shown in the illustration.

      A011VGNE01
      Text in Illustration
      *1 Protective Tape

    2. Remove the 4 bolts.

      A011XXL

    3. Pull the navigation receiver assembly with air conditioning control assembly toward the rear of the vehicle and disengage the 8 clips.

      A011W5N

    4. Disconnect each connector and remove the navigation receiver assembly with air conditioning control assembly.

  10. REMOVE RADIO RECEIVER ASSEMBLY WITH AIR CONDITIONING CONTROL ASSEMBLY (for Radio and Display Type with Intuitive Parking Assist System)

    1. Apply protective tape to the areas shown in the illustration.

      A011YDHE01
      Text in Illustration
      *1 Protective Tape

    2. Remove the 4 bolts.

      A011WRT

    3. Pull the radio receiver assembly with air conditioning control assembly toward the rear of the vehicle and disengage the 8 clips.

      A011VJQ

    4. Disconnect each connector and remove the radio receiver assembly with air conditioning control assembly.

      Tech Tips

      w/ Navigation System:

      Do not disconnect the extension module connector.

  11. REMOVE NO. 2 RADIO RECEIVER BRACKET (for Navigation Receiver Type)

    1. Remove the 5 screws and No. 2 radio receiver bracket.

      A011Z5Z

  12. REMOVE NO. 2 RADIO RECEIVER BRACKET (for Radio and Display Type with Intuitive Parking Assist System)

    1. Remove the 5 screws and No. 2 radio receiver bracket.

      A011Z5Z

  13. REMOVE HARD DISK DRIVE

    1. Remove the 2 screws.

      A011WLK

    2. Disengage the 2 guides to remove the cover.

    3. Pull out the hard disk drive from the navigation receiver assembly or radio and display receiver assembly in the direction shown by the arrow in the illustration to remove it.

      A011Z6Y