INSTRUMENT PANEL SPEAKER REMOVAL

  1. PRECAUTION (for 10 Speakers)

    Note

    except Radio and Display Type without Intuitive Parking Assist System:

    After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work Click here.

  2. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP

    1. Disconnect the front door opening trim weatherstrip LH.

      A011Y5J

  3. REMOVE FRONT PILLAR GARNISH

    1. Pull the upper part of the garnish toward the inside of the cabin and disengage the garnish from the base of the 2 clips.

      A011VPPE01
      Text in Illustration
      *1 Front Pillar Garnish Clip

      Tech Tips

      Make the front pillar garnish LH hang down from the front pillar garnish clip.

    2. While pushing the tabs on the front pillar garnish clip in the direction indicated by the arrow (1) shown in the illustration, disengage the front pillar garnish clip.

      A011XAUE01

    3. Pull the garnish in the direction indicated by the arrow (2) shown in the illustration to disengage the 2 guides and remove the front pillar garnish LH.

    4. Protect the curtain shield airbag assembly.

      A011WFKE01
      Text in Illustration
      *1 Adhesive Tape
      *2 Protective Cover
      *3 Curtain Shield Airbag Assembly

      1. Cover the airbag with a piece of cloth or nylon and secure the edges of the cover with tape as shown in the illustration.

        Note

        Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.

  4. REMOVE INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY

    1. Apply protective tape to the area shown in the illustration.

      A011Y6XE01
      Text in Illustration
      *1 Protective Tape

    2. Using a moulding remover, disengage the 2 clips and 3 claws.

      A011XMV

    3. Disengage the 2 guides to remove the No.1 instrument panel speaker panel sub-assembly.

  5. REMOVE FRONT NO. 2 SPEAKER ASSEMBLY

    1. Remove the 2 screws.

      A011XMC

    2. Lift the front No. 2 speaker assembly and disconnect the connector to remove the speaker.

      A011Z7C

      Note

      Do not touch the speaker cone.

  6. REMOVE LUGGAGE TRIM SERVICE HOLE COVER (for 10 Speakers)

    except Radio and Display Type without Intuitive Parking Assist System: Click here

  7. DISCONNECT CABLE FROM AUXILIARY BATTERY NEGATIVE TERMINAL (for 10 Speakers)

    Note

    except Radio and Display Type without Intuitive Parking Assist System:

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  8. REMOVE REAR CONSOLE BOX ASSEMBLY (for 10 Speakers)

    Click here

  9. REMOVE BOX BOTTOM MAT (for 10 Speakers)

    1. Remove the box bottom mat.

      A011WK9

  10. REMOVE UPPER CONSOLE PANEL SUB-ASSEMBLY (for 10 Speakers)

    1. Remove the 2 screws <D> or <E>.

      A011YQW

    2. Disengage the 4 clips and guide as shown in the illustration.

      A011XTM

    3. Disconnect each connector to remove the upper console panel sub-assembly.

  11. REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY (for 10 Speakers)

    1. Using a moulding remover, disengage the 2 claws and 2 clips as shown in the illustration.

      A011YA5

    2. Using a moulding remover, disengage the 2 claws and 2 clips as shown in the illustration.

      A011YX8

    3. Disengage the 3 claws and 2 clips as shown in the illustration.

      A011W28

    4. Disengage the clamp.

      A011XD5

    5. Disconnect the connector to remove the center instrument cluster finish panel assembly.

  12. REMOVE NO. 2 INSTRUMENT PANEL REGISTER ASSEMBLY (for 10 Speakers)

    1. Pull the No. 2 instrument panel register assembly in the direction indicated by the arrow to disengage the 6 clips to remove the No. 2 instrument panel register assembly.

      A011XE5

  13. REMOVE RADIO RECEIVER ASSEMBLY WITH AIR CONDITIONING CONTROL ASSEMBLY (for 10 Speakers)

    for Radio and Display Type: Click here

  14. REMOVE NAVIGATION RECEIVER ASSEMBLY WITH AIR CONDITIONING CONTROL ASSEMBLY (for 10 Speakers)

    for Navigation Receiver Type: Click here

  15. REMOVE NO. 1 SPEAKER OPENING COVER ASSEMBLY (for 10 Speakers)

    1. Disengage the 8 clips as shown in the illustration.

      A011Y0B

    2. Disconnect the connector to remove the No. 1 speaker opening cover assembly.

  16. REMOVE FRONT NO. 3 SPEAKER ASSEMBLY (for 10 Speakers)

    1. Remove the 2 screws.

      A011YFB

    2. Lift the front No. 3 speaker assembly and disconnect the connector to remove the speaker.

      A011VNQ

      Note

      Do not touch the speaker cone.