STEERING COLUMN ASSEMBLY INSTALLATION

  1. INSTALL STEERING INTERMEDIATE SHAFT ASSEMBLY

    1. Install the steering intermediate shaft assembly to the steering column assembly.

      A011W0BE01
      Text in Illustration
      *a Matchmark

      Note

      Align the matchmarks on the steering intermediate shaft assembly and the steering column assembly.

    2. Install the bolt.

      Torque:
      35 N*m  { 360 kgf*cm, 26 ft.*lbf }

  2. INSTALL STEERING POST ASSEMBLY

    1. Install the steering post assembly with the 4 nuts.

      Torque:
      25 N*m  { 255 kgf*cm, 18 ft.*lbf }

    2. Install the ground wire with the bolt.

      Torque:
      8.4 N*m  { 85 kgf*cm, 74 in.*lbf }

    3. Engage the clamp.

    4. Connect the 2 connectors.

    5. Connect the connectors and engage the wire harness clamps to the steering post assembly.

  3. INSTALL NO. 2 AIR DUCT SUB-ASSEMBLY

    1. Engage the 2 claws and guide to install the No. 2 air duct sub-assembly.

  4. CONNECT STEERING INTERMEDIATE SHAFT ASSEMBLY

    1. Connect the steering intermediate shaft assembly to the steering link assembly.

      A011Z06E01
      Text in Illustration
      *a Matchmark

      Note

      Align the matchmarks on the steering intermediate shaft assembly and the steering link assembly.

    2. Install the bolt.

      Torque:
      35 N*m  { 360 kgf*cm, 26 ft.*lbf }

    3. Tighten the clamp.

      A011W0M

  5. INSTALL TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY

    Note

    • Do not replace the spiral cable with sensor sub-assembly with the auxiliary battery connected and the power switch on (IG).

    • Do not rotate the spiral cable with sensor sub-assembly without the steering wheel with the auxiliary battery connected and the power switch on (IG).

    • Ensure that the steering wheel is installed and aligned straight when inspecting the steering sensor.

    1. Engage the 3 claws to install the turn signal switch assembly with spiral cable sub-assembly to the steering post assembly.

    2. Connect the connectors to the turn signal switch assembly with spiral cable sub-assembly.

  6. INSTALL UPPER STEERING COLUMN COVER

    1. Engage the 2 claws to install the upper steering column cover.

    2. Engage the 4 clips and 2 guides to the upper steering column cover.

  7. INSTALL LOWER STEERING COLUMN COVER

    1. Engage the 2 claws to install the lower steering column cover.

      A011YZP

    2. Install the 2 screws.

      A011VSS
      Torque:
      2.0 N*m  { 20 kgf*cm, 18 in.*lbf }

    3. Engage the claw.

      A011YPG

  8. TURN FRONT WHEELS TO FACE STRAIGHT AHEAD

  9. INSPECT AND ADJUST SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

    Note

    Do not adjust the spiral cable with sensor sub-assembly with the auxiliary battery connected and the power switch on (IG).

    1. Check that the power switch is off.

    2. Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    3. Check if the spiral cable with sensor sub-assembly is centered.

      A011X2RE01
      Text in Illustration
      A011WN4 Colored Part

      Tech Tips

      When the spiral cable with sensor sub-assembly is centered, the part indicated by A is positioned at the top and the colored part shown in the illustration is visible.

    4. If the spiral cable with sensor sub-assembly is not centered, center it.

      1. While pushing on the interlock indicated in the illustration, rotate the spiral cable with sensor sub-assembly counterclockwise slowly by hand until it stops.

        A011XNV
        Text in Illustration
        A011WQU Interlock

        Note

        • When rotating the spiral cable with sensor sub-assembly, make sure to push on the interlock indicated in the illustration to release the interlock mechanism.

        • Do not turn the spiral cable with sensor sub-assembly using the airbag wire harness.

      2. Rotate the spiral cable with sensor sub-assembly clockwise approximately 2.5 turns to the position where the colored part shown in the illustration is visible.

        A011YXM
        Text in Illustration
        A011WN4 Colored Part
        A011WQU Interlock

        Tech Tips

        The spiral cable with sensor sub-assembly will rotate approximately 2.5 turns to both the left and right from the center.

  10. INSTALL STEERING WHEEL ASSEMBLY

    1. Install the steering wheel assembly aligning the matchmarks on the steering wheel assembly and steering main shaft.

      A011VK4E01
      Text in Illustration
      *a Matchmark

    2. Install the steering wheel assembly set nut.

      Torque:
      50 N*m  { 510 kgf*cm, 37 ft.*lbf }

    3. Connect the connectors to the spiral cable sub-assembly.

  11. INSPECT STEERING WHEEL CENTER POINT

  12. INSTALL HORN BUTTON ASSEMBLY

    Click here

  13. INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY

    Click here

  14. INSTALL FRONT WHEEL LH

    Torque:
    103 N*m  { 1049 kgf*cm, 76 ft.*lbf }

  15. ADJUST PARKING ASSIST MONITOR SYSTEM (w/ Parking Assist Monitor System)

    Click here