SHIFT LEVER INSTALLATION

INSTALL FLOOR CARPET BRACKET LH

1. Engage the 2 guides.

2. Install the floor carpet bracket LH with the 2 clips.

INSTALL CONSOLE BOX INSERT

1. Engage the clip and 3 guides.

   

2. Install the console box insert with the 2 screws <D> or <E>.

INSTALL FRONT NO. 2 CONSOLE BOX INSERT

1. Engage the 2 claws to connect the room temperature sensor.

2. Engage the clip and 3 guides.

   

3. Install the front No. 2 console box insert with the 2 screws <D> or <E>.

INSTALL UPPER CONSOLE PANEL SUB-ASSEMBLY

1. Connect each connector.

2. Engage the 4 clips and guide.

3. Install the upper console panel sub-assembly with the 2 screws <D> or <E>.

INSTALL BOX BOTTOM MAT

1. Install the box bottom mat.

INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY

1. Connect each connector.

2. Engage the glove compartment light as shown in the illustration.

   

3. Engage the 3 guides and 2 clips.

   

4. Install the lower instrument panel sub-assembly with the 5 screws <D> or <E>.

INSTALL LOWER NO. 2 INSTRUMENT PANEL AIRBAG ASSEMBLY

1. Check that the power switch is off.

2. Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

   CAUTION:

   Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

3. Connect the airbag connector to the lower No. 2 instrument panel airbag assembly.

   

   Note

   When connecting any airbag connector, take care not to damage the airbag wire harness.

   Text in Illustration

   *1	Airbag Connector
   *2	Airbag Connector Lock

4. Push in the lock to install the airbag connector.

5. Temporarily install the lower No. 2 instrument panel airbag assembly with the 3 claws.

6. Install the 3 bolts.

   Torque:

   10 N*m  { 102 kgf*cm, 7 ft.*lbf }

   Note

   Confirm that the lower No. 2 instrument panel airbag assembly is installed securely without any excessive gaps and is not protruding outward.

INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

1. Connect the connector.

2. Engage the 2 guides and 4 claws to install the No. 2 instrument panel under cover sub-assembly.

INSTALL INSTRUMENT SIDE PANEL RH

1. Engage the 3 guides.

2. Engage the 4 claws to install the instrument side panel RH as shown in the illustration.

   

INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH

1. Align the alignment mark (White) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip RH.

   

   Text in Illustration

   *1	Alignment Mark (White)

   Note

   After installation, check that the corners fit correctly.

INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH

INSTALL FRONT DOOR SCUFF PLATE RH

INSTALL LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL ASSEMBLY

1. Engage the 4 claws, 9 clips and 3 guides.

2. Install the lower No. 1 instrument panel finish panel assembly with the bolt <C> and screw <D> or <E>.

CONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY

1. Engage the claw and 2 guides to connect the hood lock control lever sub-assembly.

INSTALL INSTRUMENT SIDE PANEL LH

1. Engage the 3 guides.

2. Engage the 4 claws to install the instrument side panel LH as shown in the illustration.

   

INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH

1. Align the alignment mark (Yellow) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip LH.

   

   Text in Illustration

   *1	Alignment Mark (Yellow)

   Note

   After installation, check that the corners fit correctly.

INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH

1. Insert the 2 clips in the direction indicated by the arrows shown in the illustration to engage them.

   

2. Install the cowl side trim sub-assembly LH with the clip.

INSTALL FRONT DOOR SCUFF PLATE LH

1. Engage the 10 claws to install the front door scuff plate LH.

INSPECT SHIFT LEVER POSITION

1. While moving the shift lever from the N position to each position, check that the lever moves smoothly and that the shift position indicator comes on properly according to the shift lever position.

2. Put the vehicle into the READY-on state and check the following:

   1. When the shift lever is moved to the D position, the vehicle moves forward.

   2. When the shift lever is moved to the R position, the vehicle moves in reverse.

      Note

      The vehicle should not move when the shift position indicator is off.

INSTALL LUGGAGE TRIM SERVICE HOLE COVER

1. Engage the claw to connect the luggage trim service hole cover.