POWER SWITCH REMOVAL

  1. PRECAUTION

    Note

    After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work Click here.

  2. REMOVE LUGGAGE TRIM SERVICE HOLE COVER

    1. Disengage the claw to remove the luggage trim service hole cover.

      A011YZM

  3. DISCONNECT CABLE FROM AUXILIARY BATTERY NEGATIVE TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  4. REMOVE RADIO RECEIVER ASSEMBLY WITH AIR CONDITIONING CONTROL ASSEMBLY

    Click here

  5. REMOVE NAVIGATION RECEIVER ASSEMBLY WITH AIR CONDITIONING CONTROL ASSEMBLY

    Click here

  6. REMOVE FRONT DOOR SCUFF PLATE LH

    1. Disengage the 10 claws and remove the front door scuff plate LH.

      A011XE7

  7. REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH

    1. Remove the clip.

      A011XOP

    2. Pull the cowl side trim sub-assembly LH in the direction indicated by the arrow shown in the illustration to disengage the 2 clips and remove the cowl side trim sub-assembly LH.

  8. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH

    1. Disconnect the front door opening trim weatherstrip LH.

      A011Y5J

  9. REMOVE INSTRUMENT SIDE PANEL LH

    1. Using a moulding remover, disengage the 4 claws as shown in the illustration.

      A011XLO

    2. Disengage the 3 guides and remove the instrument side panel LH as shown in the illustration.

      A011YUQ

  10. REMOVE NO. 1 INSTRUMENT CLUSTER FINISH PANEL GARNISH

    1. Disengage the 3 clips to remove the No. 1 instrument cluster finish panel garnish as shown in the illustration.

      A011YEK

  11. REMOVE NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY

    1. Apply protective tape to the area shown in the illustration.

      A011YBME01
      Text in Illustration
      *1 Protective Tape

    2. Disengage the 2 clips as shown in the illustration.

      A011WKW

    3. Using a moulding remover, disengage the 2 clips to remove the No. 1 instrument panel register assembly.

      A011X53

  12. REMOVE INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY

    1. Operate the tilt and telescopic lever to fully extend and lower the steering column assembly.

    2. Using a moulding remover, disengage the 2 claws, 4 clips and 2 guides.

      A011WPT

    3. Disengage the 5 claws, 5 clips and 2 guides.

      A011XB4

    4. Disconnect each connector.

    5. Remove the instrument cluster finish panel assembly as shown in the illustration.

      A011YPC

  13. REMOVE FRONT PANEL GARNISH LH

    1. Disengage the 3 claws, 2 clips and 8 guides to remove the front panel garnish LH.

      A011YNG

  14. DISCONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY

    1. Disengage the claw and 2 guides to disconnect the hood lock control lever sub-assembly.

      A011Y3J

  15. REMOVE LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL ASSEMBLY

    1. Remove the bolt <C> and screw <D> or <E>.

      A011XNW

    2. Disengage the 4 claws, 9 clips and 3 guides to remove the lower No. 1 instrument panel finish panel assembly.

      A011VRM

  16. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY

    1. Disengage the 4 clips and guide.

      A011Y1A

    2. Disconnect the connector and remove the lower instrument panel finish panel assembly.

  17. REMOVE POWER SWITCH

    1. Disengage the 2 claws and remove the power switch.

      A011YBC