HYBRID CONTROL SYSTEM, Diagnostic DTC:U0100-211, U0100-212, U0100-530, U0129-220, U0129-222, U0129-527, U0129-528, U0140-146, U0151-763, U0164-594, U0164-827, U1107-436

DTC Code DTC Name
U0100-211 Lost Communication with ECM / PCM "A"
U0100-212 Lost Communication with ECM / PCM "A"
U0100-530 Lost Communication with ECM / PCM "A"
U0129-220 Lost Communication with Brake System Control Module
U0129-222 Lost Communication with Brake System Control Module
U0129-527 Lost Communication with Brake System Control Module
U0129-528 Lost Communication with Brake System Control Module
U0140-146 Communication Error from Body ECU to HV ECU
U0151-763 Communication Error from Airbag ECU to HV ECU
U0164-594 Communication Error from A/C ECU to HV ECU
U0164-827 Communication Error from A/C ECU to HV ECU
U1107-436 Lost Communication with Power Management Module

DESCRIPTION

The power management control ECU transmits and receives signals via CAN communication to and from the ECM, skid control ECU assembly, power steering ECU assembly, main body ECU, airbag sensor assembly, and air conditioning amplifier assembly.

DTC No. INF Code DTC Detection Condition Trouble Area
U0100 211 Problem with CAN communication between the ECM and power management control ECU (communication error between ECUs) CAN communication system
212 Problem with CAN communication between the ECM and power management control ECU (signal transmission error)
530 Problem with CAN communication between the ECM and power management control ECU (CAN communication system malfunction)
U0129 220 Problem with CAN communication between the skid control ECU assembly and power management control ECU (no signal reception)
222 Problem with CAN communication between the skid control ECU assembly and power management control ECU (signal transmission error)
527 Problem with CAN communication (V BUS) between the skid control ECU assembly and power management control ECU (CAN communication system malfunction)
528 Problem with CAN communication between the skid control ECU assembly and power management control ECU (CAN communication system malfunction)
U0140 146 Problem with CAN communication between the main body ECU and power management control ECU (CAN communication system malfunction)
U0151 763 Problem with CAN communication between airbag sensor assembly and power management control ECU (CAN communication system malfunction)
U0164 594 Problem with CAN communication between the air conditioning amplifier assembly and power management control ECU (communication error between ECUs)
827 Problem with CAN communication between air conditioning amplifier assembly and power management control ECU (CAN communication system malfunction)
U1107 436 Problem with CAN communication between the power source ECU and power management control ECU (CAN communication system malfunction)

MONITOR DESCRIPTION

If the power management control ECU detect problem with CAN communication with the ECU, it will illuminate the MIL and set a DTC.

MONITOR STRATEGY

Related DTCs U0100 (INF 211/212/530): Verify communication
Required sensors / components

Main: Power management control ECU

Sub: CAN bus line
Frequency of operation Continuous
Duration TMC's intellectual property
MIL operation Immediately
Sequence of operation None

TYPICAL ENABLING CONDITIONS

The monitor will run whenever the following DTCs are not present TMC's intellectual property
Other conditions belong to TMC's intellectual property -

TYPICAL MALFUNCTION THRESHOLDS

TMC's intellectual property -

COMPONENT OPERATING RANGE

Power management control ECU DTC U0100 (INF 211/212/530) is not detected

CONFIRMATION DRIVING PATTERN

A011XPYE01

  1. Connect the Techstream to the DLC3.

  2. Turn the power switch on (IG) and turn the Techstream on.

  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

  4. Turn the power switch off.

  5. Turn the power switch on (READY) and after a few seconds, turn the power switch off. [A]

  6. Repeat [A] 3 times. [B]

  7. Turn the power switch on (IG) and turn the Techstream on.

  8. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes. [C]

  9. Check that permanent DTCs are cleared.

  10. If the permanent DTCs are not cleared, perform the universal trip, and then check for permanent DTCs again.

Tech Tips

  • If a permanent DTC is output, the system is malfunctioning.

  • If no permanent DTC is output, the system is normal.

INSPECTION PROCEDURE

PROCEDURE

  1. CHECK DTC OUTPUT (ALL)

    1. Connect the Techstream to the DLC3.

    2. Turn the power switch on (IG).

    3. Check for DTCs of all systems by following the prompts on the Techstream screen.

    4. Check if DTCs are output.

      Result
      Result Proceed to
      Power management control ECU outputs P2532-772 A
      Power management control ECU does not output P2532-772 B

    5. Turn the power switch off.

    B

    GO TO CAN COMMUNICATION SYSTEM Click here

    A

    GO TO DTC CHART (P2532-772) Click here