REPAIR INSTRUCTION INITIALIZATION

  1. PROCEDURES NECESSARY WHEN AUXILIARY BATTERY TERMINAL IS DISCONNECTED/RECONNECTED

    Necessary Procedures Effect/Inoperative Function When Necessary Procedures are not Performed See page
    Correct the steering angle neutral point Parking assist monitor system

    Click here

    Note

    After the power switch is turned off, the navigation receiver assembly (for Navigation Receiver Type) or radio and display receiver assembly (for Radio and Display Type with Intuitive Parking Assist System) records various types of memory and settings. As a result, after turning the power switch off, make sure to wait at least 60 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.

  2. PROCEDURES NECESSARY WHEN ECU OR OTHER PARTS ARE REPLACED

    Replacement Part Necessary Procedure Effect/Inoperative Function when Necessary Procedures are not Performed See page
    ECM Vehicle Identification Number (VIN) registration MIL comes on

    Click here

    • Throttle with motor body assembly

    • Cleaning the deposits from the throttle with motor body assembly

    • Engine assembly

    • Cylinder head sub-assembly

    • Camshaft

      (for intake or exhaust camshaft)

    • Camshaft timing gear assembly

    • Piston or piston ring

    • Mass air flow meter sub-assembly

    • Fuel injector assembly

    • Fuel pump

    • Air fuel ratio sensor

    • Engine coolant temperature sensor

    • Spark plug

    • Ignition coil assembly

    • EGR valve assembly

    • Air leaks from intake system

    • Gas leaks from exhaust system

    • Knock control sensor

    		 Inspection after repair Poor idle, engine starting, etc

    Click here

    • Door control and tire pressure monitoring system receiver assembly

    • Tire pressure warning valve and transmitter

    		 Transmitter ID registration

    • When DTC detection conditions of "transmitter ID not received" DTC are met, TPWS indicator blinks for 1 minute, and then illuminates.

    • Tire pressure warning function

    Click here

    Brake booster with master cylinder assembly

    • Initialization and calibration of the linear solenoid valve

    • Yaw rate and acceleration sensor zero point calibration

    • ABS warning light illumination

    • Brake warning light/yellow (minor malfunction) illumination

    • Slip indicator light illumination

    • VSC disable or malfunctioning

    Click here for Initialization

    Click here for Calibration

    • Brake pedal stroke sensor assembly

    • Brake pedal

    • Clearing stored linear solenoid valve calibration data

    • Initialization and calibration of the linear solenoid valve

    Click here

    Yaw rate and acceleration sensor (airbag sensor assembly)

    • Clearing zero point calibration data

    • Yaw rate and acceleration sensor zero point calibration

    Click here

    Power steering ECU assembly Assist map writing

    • P/S warning light comes on

    • EPS control

    Click here

    • Spiral cable with sensor assembly

    • Spiral cable sub-assembly

    • Steering sensor

    • Correct steering angle neutral point

    • Steering angle setting

    		 Parking assist monitor system

    Click here

    Navigation ECU sub-assembly Navigation ECU sub-assembly initialization Parking assist monitor system

    • Suspension, tires, etc (the vehicle height changes because of suspension or tires replacement)

    • Rear television camera assembly

    		 Back camera position setting Parking assist monitor system
    Blind spot monitor sensor Blind spot monitor beam axis inspection DTCs are output

    Click here

    • Roof console box assembly

    • Garage door opener transmitter

    Re-registration of codes in the garage door opener system

    • Register transmitter code

    • Rolling code systems

    		 Garage door opener system

    Click here

    DCM (Telematics Transceiver) DCM activation Safety connect system

    Click here

    • Certification ECU (smart key ECU assembly)

    • Steering lock ECU (steering lock actuator assembly)

    • Electrical key transmitter sub-assembly

    		 Code registration (Engine immobiliser system)

    • Wireless door lock control system

    • Smart Key system

    • Hybrid control system start

    • Steering lock system

    Click here

    • Occupant detection ECU

    • Front passenger seat

    		 Zero point calibration and sensitivity check. (Occupant classification system)

    • Occupant classification system

    • Passenger airbag ON/OFF indicator

    • Airbag system (Front passenger side)

    • Seat belt warning system (Front passenger)

    Click here

    • No. 1 air conditioning radiator damper servo sub-assembly

    • No. 2 air conditioning radiator damper servo sub-assembly

    • No. 1 blower damper servo sub-assembly

    		 Initialization servo motor (Air conditioning system) DTCs are output

    Click here

    • Door window regulator assembly

    • Power window regulator motor assembly

    • Door glass

    • Door glass run

    		 Initialize power window control system

    • Auto up/down function

    • Jam protection function

    • Operation function after power switch is turned off

    • Key-linked function

    • Wireless transmitter-linked function*1

    Click here

    • Sliding roof ECU (sliding roof drive gear sub-assembly)

    • Sliding roof glass sub-assembly

    • Sliding roof drive cable sub-assembly

    		 Initialize sliding roof ECU (pulse sensor initial position setting)

    • Automatic slide open/close and tilt up/down function of sliding roof

    • Jam protection function

    • Operation function after power switch is turned off

    • Key-linked function

    • Wireless transmitter-linked function*1

    • Sliding roof open warning

    Click here

    • Headlight leveling ECU assembly

    • Rear height control sensor sub-assembly

    		 Perform Headlight leveling ECU initialization Automatic headlight beam level control function

    Click here

    • *1: w/ Daytime Running Light Control