AUTOMATIC LIGHT CONTROL SENSOR REMOVAL

  1. PRECAUTION

    Note

    After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work Click here.

  2. REMOVE LUGGAGE TRIM SERVICE HOLE COVER

    for Radio and Display Type with Intuitive Parking Assist System: Click here

    for Navigation Receiver Type: Click here

  3. DISCONNECT CABLE FROM AUXILIARY BATTERY NEGATIVE TERMINAL (for Radio and Display Type with Intuitive Parking Assist System)

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  4. DISCONNECT CABLE FROM AUXILIARY BATTERY NEGATIVE TERMINAL (for Navigation Receiver Type)

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  5. REMOVE REAR CONSOLE BOX ASSEMBLY

    Click here

  6. REMOVE BOX BOTTOM MAT

    1. Remove the box bottom mat.

      A011WK9

  7. REMOVE UPPER CONSOLE PANEL SUB-ASSEMBLY

    1. Remove the 2 screws <D> or <E>.

      A011YQW

    2. Disengage the 4 clips and guide as shown in the illustration.

      A011XTM

    3. Disconnect each connector to remove the upper console panel sub-assembly.

  8. REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY

    1. Using a moulding remover, disengage the 2 claws and 2 clips as shown in the illustration.

      A011YA5

    2. Using a moulding remover, disengage the 2 claws and 2 clips as shown in the illustration.

      A011YX8

    3. Disengage the 3 claws and 2 clips as shown in the illustration.

      A011W28

    4. Disengage the clamp.

      A011XD5

    5. Disconnect the connector to remove the center instrument cluster finish panel assembly.

  9. REMOVE NO. 2 INSTRUMENT PANEL REGISTER ASSEMBLY

    1. Pull the No. 2 instrument panel register assembly in the direction indicated by the arrow to disengage the 6 clips to remove the No. 2 instrument panel register assembly.

      A011XE5

  10. REMOVE RADIO RECEIVER ASSEMBLY WITH AIR CONDITIONING CONTROL ASSEMBLY (for Radio Receiver Type)

    1. Apply protective tape to the area shown in the illustration.

      A011WKAE01
      Text in Illustration
      *1 Protective Tape

    2. Remove the 4 bolts.

      A011XHW

    3. Pull the radio receiver assembly with air conditioning control assembly toward the rear of the vehicle and disengage the 8 clips.

      A011YU4

    4. Disconnect each connector and remove the radio receiver assembly with air conditioning control assembly.

  11. REMOVE RADIO RECEIVER ASSEMBLY WITH AIR CONDITIONING CONTROL ASSEMBLY (for Radio and Display Type)

    1. Apply protective tape to the areas shown in the illustration.

      A011YDHE01
      Text in Illustration
      *1 Protective Tape

    2. Remove the 4 bolts.

      A011WRT

    3. Pull the radio receiver assembly with air conditioning control assembly toward the rear of the vehicle and disengage the 8 clips.

      A011VJQ

    4. Disconnect each connector and remove the radio receiver assembly with air conditioning control assembly.

      Tech Tips

      w/ Navigation System:

      Do not disconnect the extension module connector.

  12. REMOVE NAVIGATION RECEIVER ASSEMBLY WITH AIR CONDITIONING CONTROL ASSEMBLY (for Navigation Receiver Type)

    1. Apply protective tape to the areas shown in the illustration.

      A011VGNE01
      Text in Illustration
      *1 Protective Tape

    2. Remove the 4 bolts.

      A011XXL

    3. Pull the navigation receiver assembly with air conditioning control assembly toward the rear of the vehicle and disengage the 8 clips.

      A011W5N

    4. Disconnect each connector and remove the navigation receiver assembly with air conditioning control assembly.

  13. REMOVE NO. 1 SPEAKER OPENING COVER ASSEMBLY

    1. Disengage the 8 clips as shown in the illustration.

      A011Y0B

    2. Disconnect the connector to remove the No. 1 speaker opening cover assembly.

  14. REMOVE AUTOMATIC LIGHT CONTROL SENSOR

    1. Disengage the 2 claws and remove the automatic light control sensor from the No. 1 speaker opening cover assembly.

      A011YUP