OUTER MIRROR SWITCH INSPECTION

  1. INSPECT OUTER MIRROR SWITCH ASSEMBLY

    1. w/o Retract mirror

      1. Check the mirror select switch and mirror surface adjust switch.

      2. Turn the mirror select switch to the L position.

        A011VDRE05

      3. Measure the resistance according to the value(s) in the table below.

        Text in Illustration
        *1 Mirror select switch
        *2 Mirror surface adjust switch
        *a

        Component without harness connected

        (Outer Mirror Switch Assembly)
        Standard Resistance (for left side)
        Tester Connection Switch Condition Specified Condition

        9 (MLV) - 13 (B)

        11 (M+) - 12 (E)

        		 UP Below 1 Ω
        OFF 10 kΩ or higher

        9 (MLV) - 12 (E)

        11 (M+) - 13 (B)

        		 DOWN Below 1 Ω
        OFF 10 kΩ or higher

        10 (MLH) - 13 (B)

        11 (M+) - 12 (E)

        		 LEFT Below 1 Ω
        OFF 10 kΩ or higher

        10 (MLH) - 12 (E)

        11 (M+) - 13 (B)

        		 RIGHT Below 1 Ω
        OFF 10 kΩ or higher

      4. Turn the mirror select switch to the R position.

      5. Measure the resistance according to the value(s) in the table below.

        Standard Resistance (for right side)
        Tester Connection Switch Condition Specified Condition

        8 (MRV) - 13 (B)

        11 (M+) - 12 (E)

        		 UP Below 1 Ω
        OFF 10 kΩ or higher

        8 (MRV) - 12 (E)

        11 (M+) - 13 (B)

        		 DOWN Below 1 Ω
        OFF 10 kΩ or higher

        7 (MRH) - 13 (B)

        11 (M+) - 12 (E)

        		 LEFT Below 1 Ω
        OFF 10 kΩ or higher

        7 (MRH) - 12 (E)

        11 (M+) - 13 (B)

        		 RIGHT Below 1 Ω
        OFF 10 kΩ or higher

        If the result is not as specified, replace the outer mirror switch assembly.

    2. Check the LED illuminates (w/o Retract mirror).

      1. Apply auxiliary battery voltage to the outer mirror switch assembly and check that the LED illuminates.

        A011VDRE03
        Standard
        Measurement Condition Specified Condition

        Auxiliary battery positive (+) → Terminal 6 (ILL+)

        Auxiliary battery negative (-) → Terminal 16 (ILL-)

        		 LED illuminates
        Text in Illustration
        *a

        Component without harness connected

        (Outer Mirror Switch Assembly)

        If the result is not as specified, replace the outer mirror switch assembly.

    3. w/ Retract mirror

      1. Check the mirror select switch and mirror surface adjust switch.

      2. Turn the mirror select switch to the L position.

        A011W1EE12

      3. Measure the resistance according to the value(s) in the table below.

        Text in Illustration
        *1 Mirror select switch
        *2 Mirror surface adjust switch
        *a

        Component without harness connected

        (Outer Mirror Switch Assembly)
        Standard Resistance (for left side)
        Tester Connection Switch Condition Specified Condition

        9 (MLV) - 13 (B)

        11 (M+) - 12 (E)

        		 UP Below 1 Ω
        OFF 10 kΩ or higher

        9 (MLV) - 12 (E)

        11 (M+) - 13 (B)

        		 DOWN Below 1 Ω
        OFF 10 kΩ or higher

        10 (MLH) - 13 (B)

        11 (M+) - 12 (E)

        		 LEFT Below 1 Ω
        OFF 10 kΩ or higher

        10 (MLH) - 12 (E)

        11 (M+) - 13 (B)

        		 RIGHT Below 1 Ω
        OFF 10 kΩ or higher

      4. Turn the mirror select switch to the R position.

      5. Measure the resistance according to the value(s) in the table below.

        Standard Resistance (for right side)
        Tester Connection Switch Condition Specified Condition

        8 (MRV) - 13 (B)

        11 (M+) - 12 (E)

        		 UP Below 1 Ω
        OFF 10 kΩ or higher

        8 (MRV) - 12 (E)

        11 (M+) - 13 (B)

        		 DOWN Below 1 Ω
        OFF 10 kΩ or higher

        7 (MRH) - 13 (B)

        11 (M+) - 12 (E)

        		 LEFT Below 1 Ω
        OFF 10 kΩ or higher

        7 (MRH) - 12 (E)

        11 (M+) - 13 (B)

        		 RIGHT Below 1 Ω
        OFF 10 kΩ or higher

        If the result is not as specified, replace the outer mirror switch assembly.

    4. Check the mirror retract switch (w/ Retract mirror).

      1. Measure the resistance according to the value(s) in the table below.

        A011W1EE13
        Text in Illustration
        *1 Mirror retract switch
        *a

        Component without harness connected

        (Outer Mirror Switch Assembly)
        Standard Resistance
        Tester Connection Switch Condition Specified Condition
        15 (MF) - 12 (E) Mirror retract switch retract position Below 1 Ω
        14 (MR) - 13 (B) Below 1 Ω
        15 (MF) - 13 (B) Mirror retract switch return position Below 1 Ω
        14 (MR) - 12 (E) Below 1 Ω

        If the result is not as specified, replace the outer mirror switch assembly.

    5. Check the LED illuminates (w/ Retract mirror).

      1. Apply auxiliary battery voltage to the outer mirror switch assembly and check that the LED illuminates.

        A011W1EE14
        Standard
        Measurement Condition Specified Condition

        Auxiliary battery positive (+) → Terminal 6 (ILL+)

        Auxiliary battery negative (-) → Terminal 16 (ILL-)

        		 LED illuminates
        Text in Illustration
        *a

        Component without harness connected

        (Outer Mirror Switch Assembly)

        If the result is not as specified, replace the outer mirror switch assembly.