POWER WINDOW REGULATOR MOTOR (for Rear Door) INSTALLATION

Tech Tips

  • Use the same procedure for both the RH and LH sides.

  • The procedure described below is for the LH side.

  1. INSTALL REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY

    Note

    The regulator arm must be below the intermediate position when installing the rear power window regulator motor assembly.

    1. Using a T25 "TORX" socket wrench, install the rear power window regulator motor assembly with the 3 screws.

      A011XW5
      Torque:
      5.4 N*m  { 55 kgf*cm, 48 in.*lbf }

      Tech Tips

      When replacing the rear window regulator, a new rear window regulator uses self-tapping screws to thread new installation holes when the self-tapping screws are inserted.

  2. INSTALL REAR DOOR WINDOW REGULATOR ASSEMBLY

    1. Apply MP grease to the sliding parts of the rear door window regulator assembly.

    2. Install the temporary bolt to the rear door window regulator assembly.

    3. Temporarily install the rear door window regulator assembly.

      A011WNHE02
      Text in Illustration
      *1 Temporary Bolt

    4. Tighten the temporary bolt and 3 bolts to install the rear door window regulator assembly.

      Tech Tips

      Tighten the bolts in the order shown in the illustration.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

  3. INSTALL REAR DOOR GLASS SUB-ASSEMBLY

    1. Slide the rear door glass sub-assembly to install it as shown in the illustration.

      A011W7K

  4. INSTALL REAR DOOR QUARTER WINDOW GLASS

    1. Install the rear door quarter window glass together with the rear door quarter window weatherstrip in the direction indicated by the arrow in the illustration.

      A011VT4

  5. INSTALL REAR DOOR LOWER WINDOW FRAME SUB-ASSEMBLY

    1. Install the rear door lower window frame sub-assembly with the screw and 2 bolts.

      A011VWO

  6. INSTALL REAR DOOR GLASS RUN

    1. Install the rear door glass run.

      A011YRB

  7. INSTALL REAR DOOR WEATHERSTRIP

    1. Install the upper part of rear door weatherstrip as shown in the illustration.

      A011XXP

  8. INSTALL REAR DOOR SERVICE HOLE COVER

    1. Apply new butyl tape to the rear door panel.

    2. Pass the rear door lock remote control cable assembly, rear door inside locking cable assembly and each connector through a new rear door service hole cover.

      A011Z09E01
      Text in Illustration
      *1 Reference Point

    3. Attach the rear door service hole cover according to the reference points on the rear door panel.

      Note

      Securely install the rear door service hole cover preventing wrinkles and air bubbles.

    4. Connect the connector.

  9. INSTALL REAR DOOR INNER GLASS WEATHERSTRIP

    1. Install the rear door inner glass weatherstrip.

      A011Z1F

  10. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY

    1. Install the No. 1 door scuff plate clamp as shown in the illustration.

      A011VVN

    2. Connect the rear door lock remote control cable assembly and rear door inside locking cable assembly.

      A011Y3QE01
      Text in Illustration
      *1 Rear Door Inside Locking Cable Assembly
      *2 Rear Door Lock Remote Control Cable Assembly

    3. Engage the rear door trim board sub-assembly with the 4 claws and reference boss as shown in the illustration.

      A011YMNE01
      Text in Illustration
      *1 Reference Boss

    4. Engage the 8 clips and install the rear door trim board sub-assembly.

      A011WJU

    5. Install the 3 screws.

    6. If protective tape has been applied, remove it.

  11. INSTALL REAR ARMREST ASSEMBLY

    1. Engage the 2 guides, 3 clips and 7 claws to install the rear armrest assembly.

      A011Y2U

  12. INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL

    1. Connect the connector.

    2. Engage the 4 guides, 2 clips and 5 claws to install the rear power window regulator switch assembly with rear door armrest base panel.

      A011WHT

  13. INSTALL REAR DOOR INSIDE HANDLE BEZEL PLUG

    1. Engage the 3 claws to install the rear door inside handle bezel plug.

      A011XD4

  14. CONNECT CABLE TO AUXILIARY BATTERY NEGATIVE TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected. Click here

  15. INSTALL LUGGAGE TRIM SERVICE HOLE COVER

    1. Engage the claw to connect the luggage trim service hole cover.

  16. INSPECT POWER WINDOW OPERATION

    Click here