THEFT DETERRENT


  1. FUNCTION


    1. The theft deterrent system has the following functions:

      Function Outline
      Alarm When the theft deterrent system switches to the alarm state, the warning items are operated and the alarm sounds for approximately 27.5 seconds.
      Alarm Indicator When the theft deterrent system switches to the armed preparation state or alarm state, the security indicator light is illuminated to inform the user. This indicator is also the engine immobiliser indicator, which blinks when the engine immobiliser is in the set state.
      Forced Door Lock

      The main body ECU (multiplex network body ECU) transmits a door lock signal to all the doors when all the following conditions are met:


      • The theft deterrent system is in the alarm state.

      • There is no electrical key transmitter sub-assembly in the actuation area.

      • One of the doors has been unlocked.

      The function stops when one of the following conditions is met:


      • All doors are locked.

      • The warning ends after approximately 27.5 seconds.

      • The electrical key transmitter sub-assembly is in the actuation area.

  2. SYSTEM CONTROL


    1. The states of the theft deterrent system are as follows:

      State Description Theft Detection
      Disarmed State The theft deterrent system has not been set by the user. Not possible
      Armed Preparation State This is the preparation state before the theft deterrent system becomes active (enters the armed state) when the system has been set by the user. Not possible
      Armed State The theft deterrent system is active. (Theft can be detected.) Possible
      Alarm State A theft attempt has been detected and the warning operation activates. Possible
      A0121P4E01

    2. The theft deterrent system activates as shown in the diagram above when one of the items in the table occurs in order to cause the system to enter the respective state.

      Models with Entry Function
      Condition Item
      (1)

      In disarmed state 1, when the power switch is off, the system state is switched if the following condition is met:


      • With all the doors and engine hood closed, all doors are locked by wireless door lock control function, entry and start system or key linked power door lock operation.
      (2) Approximately 30 seconds elapse.
      (3)

      • All doors are unlocked by wireless operation or the entry and start system.

      • Any door is unlocked.

      • Any door is opened.

      • The power switch is pushed.

      • The auxiliary battery is reconnected.
      (4)

      • The engine hood is opened when the engine hood is closed.

      • The auxiliary battery is reconnected.

      • Any door is opened when all doors are closed.

      • Any door is unlocked when all doors are locked.

      • When 5 seconds or more have elapsed after the power switch is pushed, the power source mode changes to on (IG).

      • The engine hood is opened.

      • The back door is opened.

      • When the intrusion sensor (theft warning ultrasonic sensor) detects an intruder.

      • Any door is unlocked.

      • The main body ECU (multiplex network body ECU) detects an open circuit in any of the print pattern type glass breakage sensors.

        Note

        Ultrasonic waves are used to detect intrusion. Ultrasonic waves do not penetrate steel or glass. When any door glass or sliding roof is left open, ultrasonic waves may escape. This may result in the detection of people in the surroundings, leaves or insects entering the vehicle, strong wind or other ultrasonic wave sources in the environment when the vehicle is parked with a door glass or sliding roof open. When parking the vehicle with a door glass or the sliding roof open for ventilation, turn off the intrusion sensor (theft warning ultrasonic sensor) using the intrusion sensor cancel switch.
      (5)

      • The power source mode is turned to on (IG) and the hybrid system is running.

      • All doors are unlocked by wireless operation or the entry and start system.
      (6) After approximately 27.5 seconds, the alarm stops and 5 seconds later the system returns to armed state.
      (7) The engine hood is closed when the engine hood is opened.
      (8)

      • Any door is unlocked when all doors are locked.

      • Any door is opened.

      • The power switch is pushed.

      • The auxiliary battery is reconnected.

      • All doors are unlocked by wireless operation or the entry and start system.

      • The power source mode changes to on (ACC) or on (IG).
      (9)

      In disarmed state 1, when the power switch is off, the system state is switched if the following condition is met:


      • With all doors closed, and the engine hood opened, all doors are locked by wireless operation or the entry and start system.
      (10) The engine hood is opened.
      Models without Entry Function
      Condition Item
      (1)

      In disarmed state 1, when the power switch is off, the system state is switched if the following condition is met:


      • With the doors and the engine hood closed, all doors are locked by wireless operation.
      (2) Approximately 30 seconds elapse.
      (3)

      • All doors are unlocked by wireless operation.

      • Any door is unlocked.

      • Any door is opened.

      • The power switch is pushed.

      • The auxiliary battery is reconnected.
      (4)

      • The engine hood is opened when the engine hood is closed.

      • The auxiliary battery is reconnected.

      • Any door is opened when all doors are closed.

      • Any door is unlocked when all doors are locked.

      • When 5 seconds or more have elapsed after the power switch is pushed, the power source mode changes to on (IG).

      • The engine hood is opened.

      • The back door is opened.

      • When the intrusion sensor (theft warning ultrasonic sensor) detects an intruder.

      • The main body ECU (multiplex network body ECU) detects an open circuit in any of the print pattern type glass breakage sensors.

        Note

        Ultrasonic waves are used to detect intrusion. Ultrasonic waves do not penetrate steel or glass. When any door glass or sliding roof is left open, ultrasonic waves may escape. This may result in the detection of people in the surroundings, leaves or insects entering the vehicle, strong wind or other ultrasonic wave sources in the environment when the vehicle is parked with a door glass or sliding roof open. When parking the vehicle with a door glass or the sliding roof open for ventilation, turn off the intrusion sensor (theft warning ultrasonic sensor) using the intrusion sensor cancel switch.
      (5)

      • The power source mode is turned to on (IG) and the hybrid system is running.

      • All doors are unlocked by wireless operation.
      (6) After approximately 27.5 seconds, the alarm stops and 5 seconds later system returns to armed state.
      (7) The engine hood is closed when the engine hood is opened.
      (8)

      • Any door is unlocked when all doors are locked.

      • Any door is opened.

      • The power switch is pushed.

      • The auxiliary battery is reconnected.

      • All doors are unlocked by wireless operation.

      • The power source mode changes to on (ACC) or on (IG).
      (9)

      In disarmed state 1, when the power switch is off, the system state is switched if the following condition is met:


      • With all doors closed and the engine hood opened, all doors are locked by wireless operation.
      (10) The engine hood is opened.

  3. CONSTRUCTION


    1. Self-power Siren


      1. During normal operation, the self-power siren sounds an alarm in accordance with the operation signal from the main body ECU (multiplex network body ECU). Because this siren has an internal battery, it can independently sound an alarm even if the vehicle battery terminals are disconnected or if the wiring harnesses that are related to the system are cut.

    2. Intrusion Sensor (Theft Warning Ultrasonic Sensor)


      1. An intrusion sensor (theft warning ultrasonic sensor) is provided in the map light assembly. If the intrusion sensor (theft warning ultrasonic sensor) detects an inappropriate entry into the vehicle interior by an intruder (including intrusions made by breaking window glass), a warning signal is sent to the main body ECU (multiplex network body ECU). This sensor transmits ultrasonic waves in the vehicle interior. When an intruding object moves, it disrupts the reflection of the ultrasonic waves, and the sensor detects the resulting changes in the phase of the ultrasonic waves. The intrusion sensor (theft warning ultrasonic sensor), which is linked to the auto alarm system, sets automatically when the system transfers to the armed state (and the setting of the auto alarm is completed). When the intrusion sensor (theft warning ultrasonic sensor) detects a moving object in the vehicle interior, the system transfers to the alarm state. Then, the system sounds the horn intermittently and blinks the hazard warning light for approximately 27.5 seconds and performs a forced locking operation.

        Tech Tips

        Ultrasonic waves are used to detect intrusion. Ultrasonic waves do not penetrate steel or glass. When any of the side windows or sliding roof is left open, ultrasonic waves may escape. This may result in the detection of people in the surroundings, leaves or insects entering the vehicle, strong wind or other ultrasonic wave sources in the environment when the vehicle is parked with the side windows open. When parking the vehicle with the side windows open for ventilation, turn off the intrusion sensor (theft warning ultrasonic sensor) using the intrusion sensor cancel switch.

    3. Intrusion Sensor Cancel Switch


      1. An intrusion sensor cancel switch is provided in the map light assembly. When the system is in the disarmed state, pressing the intrusion sensor cancel switch can disable the function of the intrusion sensor (theft warning ultrasonic sensor).

    4. Glass Breakage Sensor


      1. By sending signals through the connected sensor strips on the back door glass and quarter window assembly*, the glass breakage sensor can detect breakage of those glasses.

      2. The glass breakage sensors are linked to the theft deterrent system, and they will automatically be set when the system enters the armed state. During the armed state, when the glass breakage sensor detects an open circuit of the print patterns on the back door glass and quarter window assembly*, it transmits a signal indicating glass breakage to the main body ECU (multiplex network body ECU), and the system enters the alarm state.


        • *: Wagon Models