METER / GAUGE SYSTEM DETAILS


  1. OPERATING CONDITION


    1. Hybrid System Indicator Operation


      1. The Hybrid System Indicator will begin to operate when both of the following conditions are met:


        • The hybrid system is operating (the READY indicator light is illuminated).

        • The shift position is not in P, R or N.

  2. FUNCTION


    1. Combination Meter Assembly


      1. Buzzer Function


        1. The table below shows the warning and reminder functions of the buzzer in the combination meter assembly.

        1 READY (Once) 2 Driver Side Seat Belt Warning (5 Times at the Maximum)
        3 Driver Side Seat Belt Warning (Once) 4 Passenger Side Seat Belt Warning (Once)
        5 Seat Belt Warning (Level 2) 6 Seat Belt Warning (Level 1)
        7 Brake System Warning 8 EPS Warning
        9 Smart Key System Warning 1 (Continuous) 10 Smart Key System Warning 2 (Intermittent)
        11 Key Reminder Indicating Buzzer 12 Brake System Temperature Warning
        13 Hill-start Assist Control Reset Indication 14 Hill-start Assist Control Set Indication
        15 Smart Key System Warning 2 (Continuous, 9 times at the maximum) 16 Smart Key System Warning (Once)
        17 Multi-information Display Warning 18 Accelerator Depression with Neutral (N) Selected
        19 Hybrid System Check (Intermittent) 20 Hybrid System Check (Once)
        21 HV Battery Low Warning 22 HV Battery Charge Request
        23 Immobiliser Certification Reminder 24 Shift Position (P) Request
        25 Parking Brake Engaged Warning 26 Door Open while Driving Warning
        27 Shift Operation Reject Warning 28 EV Drive Mode Reject Warning
        29 Headlight Reminder 30 Sliding Roof Open Warning*
        31 Turn Signal/Hazard Warning Operation - -

        • *: Models with sliding roof system

      2. Maintenance Required Reminder Function


        • A maintenance required reminder function will appear to remind the driver to have maintenance performed based on the vehicle driving distance.

        • The combination meter assembly calculates the vehicle driving distance based on the signals from the skid control ECU.

        • There are 2 types of warnings:


          • When the driving distance accumulated since last reset exceeds 4500 miles, the multi-information display will show the warning message.

          • If the driving distance accumulated since last reset exceeds 5000 miles, the multi-information display will show the warning message.

          • The maintenance required reminder message appears on the multi-information display as follows:

            4500 miles or more 5000 miles or more
            OIL MAINTENANCE REQUIRED SOON appears for approximately 15 seconds OIL MAINTENANCE REQUIRED warning remains on

        • After maintenance has been performed, the accumulated vehicle driving distance memorized in the combination meter assembly should be reset to zero using the ODO/TRIP switch.

        Tech Tips

        The accumulated vehicle driving distance memorized in the combination meter assembly can be reset using the following procedure.


        • Turn the power switch on (IG), and make sure that TRIP A is displayed on the Liquid Crystal Display (LCD).

        • Turn the power switch off. While pushing the ODO/TRIP switch, turn the power switch on (IG).

        • With the power switch on (IG), keep holding the ODO/TRIP switch (for at least 5 seconds) with the LCD counting down. Release the ODO/TRIP switch when the resetting procedure has completed.

        • As the resetting completes, the odometer will display "000000" for 1 second.

    2. Multi-information Display


      1. Display Flow Function


        1. The multi-information display flow can be switched as shown in the flow chart below:

          A01HS6ZE02
          No. Transition Condition
          *1 Conditions are not met and all new messages have been displayed.
          *2 If the display conditions for 2 or more messages are met, relevant messages are alternately displayed for 2 seconds each.
          *3 If the power switch is turned off during the "Opening" display, the "Opening" display will be shown from the beginning.
          *4 If the DISP switch is used to change from an advisory message to the cruise information display screen, repeatedly operating the DISP switch will cycle through the cruise information screens and then return the advisory message if the display conditions are still met.
          *5 If the DISP switch is not operated for more than 6 seconds with any of the caution or warning message display conditions still met, the relevant caution or warning messages are displayed.

      2. Cruise Information Mode Function


        • The cruise information is displayed in the following order each time the DISP switch of the steering pad switch assembly is pressed.

        A01HS5DE01
        Text in Illustration
        *1 DISP Switch - -
        A01HRZQ DISP switch pressed briefly. - -

        • The cruise information mode items displayed are as follows:

        No. Information Outline
        (1) Cruising Range

        • Displays a value that has been calculated by the combination meter assembly. When the power switch is turned on (IG), the combination meter assembly calculates the range based on continuously monitoring and storing information on fuel consumption data, and the residual fuel volume.

        • This display is updated every 10 seconds.
        Average Fuel Consumption

        • Displays a value that has been calculated by the combination meter assembly based on the distance driven and the fuel consumption volume (fuel injection signal from the ECM).

        • This display is updated every 10 seconds.
        (2) Average Speed

        • Displays the average vehicle speed calculated by the combination meter assembly based on the engine start signal and vehicle speed signal.

        • This display is updated every 10 seconds.
        Elapsed Time Displays the length of time since the engine was started.
        (3) Eco Drive Level Display

        • Displays the average fuel consumption calculated since the engine was started. Uses 4 different height bars to display the level.

        • This display is updated every 10 seconds.
        (4) Energy Monitor

        • Displays the energy transmission direction for checking the current drive method (engine, motor or both), whether the engine is being used to generate power or whether energy is being regenerated.

        • The energy flow, which appears in the form of an arrow, also shows the SOC of the HV battery in 8 levels.

        • This display is updated every 0.3 seconds.
        (5) Settings Customizes the combination meter assembly language display and EV drive indicator light and instantaneous fuel consumption gauge deactivated or activated display states.
        (6) Blank Screen -

      3. Eco Drive Level


        • The eco drive level changes among 4 levels to indicate the average fuel consumption.

        • After the power switch is turned off, the eco drive level display appears for 3 seconds in the multi-information display. When the average fuel consumption is 41.0 MPG or more*1, 18.0 km/L or more*2 or 5.8 L/100 km or less*3, the "EXCELLENT!" message flashes.


        • *1: Models for U.S.A.

        • *2: Destination package for Canada

        • *3: Destination package for South Korea

        Average Fuel Consumption Level Multi-information Display
        MPG L/100 km km/L
        Level 0

        (25.0 or less)

        A01HRX1

        (9.0 or more)

        A01HS3Q

        (10.0 or less)

        A01HRYC
        Level 1

        (25.0 to 30.0)

        A01HS3G

        (8.0 to 9.0)

        A01HS8Q

        (10.0 to 12.5)

        A01HS5H
        Level 2

        (30.0 to 35.0)

        A01HRU8

        (7.0 to 8.0)

        A01HRY0

        (12.5 to 15.0)

        A01HS26
        Level 3

        (35.0 to 40.0)

        A01HS77

        (6.0 to 7.0)

        A01HS42

        (15.0 to 17.5)

        A01HRU1
        Level 4 When driving

        (40.0 or more)

        A01HS05

        (6.0 or less)

        A01HS4K

        (17.5 or more)

        A01HRUI
        After power switch is turned off

        (41.0 or more)

        A01HS58

        (5.8 or less)

        A01HRZ9

        (18.0 or more)

        A01HS9O

      4. Customization Function


        • In the settings screen of cruise information mode, pressing and holding the DISP switch enters setting mode.

        • Press the DISP switch briefly to select the item to be customized. Press and hold the DISP switch to confirm the selection.

        A01HRYFE01
        Text in Illustration
        *a Language Setting *b Instantaneous Fuel Consumption Gauge ON/OFF Setting
        *c EV Drive Indicator Light ON/OFF Setting - -
        A01HRZQ DISP switch pressed briefly. A01HS1C DISP switch pressed and held.
        A01HRW4 If the vehicle has reached a speed of 8 km/h (5 mph) - -

        • In setting mode, the following items of the combination meter assembly can be customized.

        Item Available Setting
        Language

        • English

        • French

        • Spanish
        Instantaneous Fuel Consumption Gauge

        • On

        • Off
        EV Drive Indicator Light

        • On

        • Off

      5. Warning Mode Function


        • When a warning is necessary, the warning display interrupts the display in the multi-information display.

        • The master warning light may illuminate or blink and the buzzer in the combination meter assembly may sound depending on the item in the multi-information display.

        Priority Indication/Warning Master Warning Light Buzzer
        1 MAINTENANCE MODE - -
        CERTIFICATION MODE - -
        2 Door Open (While Driving)*1 Blinks Sounds
        Door Open - -
        Clearance Sonar Obstruction Detection*2 - -
        CHECK SONAR*2 Illuminates Sounds
        CLEAN SONAR*2 Illuminates Sounds
        3 AUTO POWER OFF TO CONSERVE BATTERY - -
        4 SHIFT TO P POSITION Blinks Sounds
        SHIFT TO P POSITION WHEN PARKED Blinks Sounds
        N POSITION Blinks Sounds
        TRACTION BATTERY PRESERVATION MODE RESTART AFTER SHIFTING TO THE P POSITION Blinks Sounds
        5 TRACTION BATTERY LOW. CHARGE WHEN NOT IN N POSITION Blinks Sounds
        RELEASE PARKING BRAKE Blinks Sounds
        KEY NOT DETECTED Blinks Sounds
        6 CHECK HYBRID SYSTEM Illuminates Sounds
        CHECK SMART KEY SYSTEM Blinks Sounds
        BSM NOT AVAILABLE Illuminates Sounds
        CHECK BSM SYSTEM Illuminates Sounds
        7 CHECK CRUISE CONTROL SYSTEM Illuminates Sounds
        8 TURN POWER OFF Blinks Sounds
        9 KEY DETECTED IN VEHICLE Blinks Sounds
        TURN LIGHTS OFF Blinks Sounds
        MOONROOF OPEN Blinks Sounds
        DEPRESS BRAKE PEDAL, TOUCH POWER SWITCH WITH KEY Blinks Sounds
        DEPRESS BRAKE PEDAL AND PUSH POWER SWITCH TO START Blinks Sounds
        STEERING LOCK ACTIVE Blinks Sounds
        SHIFT TO P POSITION TO START Blinks Sounds
        10 KEY BATTERY LOW Illuminates Sounds
        HYBRID SYSTEM OVERHEAT Illuminates Sounds
        11 DRIVE FORCE LIMITED - -
        12 LOW WASHER FLUID - -
        OIL MAINTENANCE REQUIRED SOON - -
        OIL MAINTENANCE REQUIRED - -
        RESETTING OIL MAINTENANCE DATA - -
        RESETTING OF OIL MAINTENANCE DATA INCOMPLETE - -
        POWER ON - -
        Engine start ready state - -
        EV MODE CURRENTLY NOT AVAILABLE - Sounds
        EV MODE NOT AVAILABLE WARMING UP - Sounds
        EV MODE NOT AVAILABLE LOW BATTERY - Sounds
        EV MODE NOT AVAILABLE EXCESSIVE SPEED - Sounds
        EV MODE NOT AVAILABLE EXCESSIVE ACCELERATION - Sounds
        EV MODE DEACTIVATED - Sounds
        EV MODE DEACTIVATED LOW BATTERY - Sounds
        EV MODE DEACTIVATED EXCESSIVE SPEED - Sounds
        EV MODE DEACTIVATED EXCESSIVE ACCELERATION - Sounds

        • *1: If the vehicle has reached a speed of 5 km/h (3 mph)

        • *2: Models with intuitive parking assist system