METER / GAUGE SYSTEM DETAILS

Multi-information Display

1. Display Flow Function

   
   

   1. The multi-information display flow can be switched as shown in the flow chart below:

      

      No.	Transition Condition
      *1	Conditions are not met and all new messages have been displayed.
      *2	If the display conditions for 2 or more messages are met, relevant messages are alternately displayed for 2 seconds each.
      *3	If the engine switch is turned to off during the "Opening" display, the "Opening" display will be shown from the beginning.
      *4	If the DISP switch is used to change from an advisory message to the cruise information display screen, repeatedly operating the DISP switch will cycle through the cruise information screens and then return the advisory message if the display conditions are still met.
      *5	If the DISP switch is not operated for more than 6 seconds with any of the caution or warning message display conditions still met, the relevant caution or warning messages are displayed.
      *6	Conditions for displaying new messages are met, or the vehicle speed is more than 8 km/h (5 mph).

2. Cruise Information Mode Function

   
   

   • The cruise information is displayed in the following order each time the DISP switch of the steering pad switch assembly is pressed.

   

   Text in Illustration

   *a	The item that is always displayed does not appear when the cruise information item is switched as shown above.	*b	The item selection screen is displayed.
   	DISP switch pressed briefly.		DISP switch pressed and held.

   
   

   • The cruise information mode items displayed are as follows:

   No.	Information	Outline
   (1)	Eco Driving Indicator Zone Display	Displays Eco driving state by the movement of the bar on Eco driving indicator zone display after the comparison of Eco driving range with the current acceleration. Displays a value that has been calculated by the ECM. When the engine switch is turned on (IG), the ECM calculates the Eco driving ratio based on the vehicle speed, accelerator pedal operation, shift position, engine speed, shift range and driving mode signals. This display is updated every 0.2 seconds.
   (2)	Ambient Temperature	Displays the ambient temperature.
   (3)	Current Fuel Consumption	Displays a value that has been calculated by the combination meter assembly. When the engine switch is turned on (IG), the combination meter assembly calculates this value based on the distance driven and the fuel consumption volume (fuel injection signal from the No. 1 injector). This display is updated every 0.5 seconds.
   (4)	Average Fuel Consumption After Refueling	Displays the value calculated by the combination meter assembly based on the distance driven since refueling and the fuel consumption volume (fuel injection signals from the No. 1 injector). The combination meter assembly determines the vehicle has been refueled through the signal from the fuel sender gauge. This display is updated every 10 seconds.
   (5)	Average Fuel Consumption	Displays a value that has been calculated by the combination meter assembly based on the distance driven and the fuel consumption volume (fuel injection signal from the ECM). This display is updated every 10 seconds.
   (6)	Average Speed	Displays the average vehicle speed calculated by the combination meter assembly based on the engine start signal and vehicle speed signal. This display is updated every 10 seconds.
   (7)	Cruising Range	Displays a value that has been calculated by the combination meter assembly. When the engine switch is turned on (IG), the combination meter assembly calculates the range based on continuously monitoring and storing information on fuel consumption data, and the residual fuel volume. This display is updated every 10 seconds.
   (8)	Elapsed Time	Displays the length of time since the engine was started.
   (9)	Tire Inflation Pressure	Displays the tire inflation pressure.
   (10)	Settings	Customizes the combination meter assembly language display, Eco Driving Indicator Light and instantaneous fuel consumption gauge deactivated or activated display states.
   (11)	Blank Screen	-

3. Customization Function

   
   

   • In the settings screen of cruise information mode, pressing and holding the DISP switch enters setting mode.

   • Press the DISP switch briefly to select the item to be customized. Press and hold the DISP switch to confirm the selection.

   

   Text in Illustration

   DISP switch pressed and held.

   -

   -

   
   

   • In settings mode, the following items of the combination meter assembly can be customized.

   Item		Available Setting
   Meter	Language	English French Spanish Chinese Russian
   	Units	Km (km/L) Km (L/100km)
   	Eco Lamp (Meter Panel Illumination / Eco Driving Indicator Light	On (Always) / On On (Always) / Off On (Self-lighting) / Off Off / On Off / Off
   	Drive Monitor	Fuel consumption Cruising range Outside
   	Lamp brightness	Bright Standard
   	Sport Lamp	On Off
   Door*	Auto Unlock by Shift to P	On Off
   	Auto Lock by Speed	On Off
   	Auto Lock by Shift from P	On Off
   	Auto Unlock by Driver Door	On Off
   	Lock/Unlock Feedback-Lights	On Off
   	Auto Relock Timer	120 sec. 60 sec. 30 sec. Off
   	Remote 2-Press Unlock	On Off
   Smart Entry and Start System*	Access System with Elec. Key	On Off
   	Select Doors to Unlock	Driver's Door All Doors
   	Lock/Unlock Feedback-Tone	Level 7 (Maximum) Level 6 Level 5 Level 4 Level 3 Level 2 Level 1 (Minimum) Off
   Lighting*	Headlamps-On Sensitivity	Level 5 Level 4 Level 3 Level 2 Level 1
   	Daytime Running Lights	On Off
   	Interior Lights Off Timer	30 sec. 15 sec. 7.5 sec. Off
   	Exterior Lights Off Timer	30 sec. 15 sec. 7.5 sec. Off
   Seat*	Driver's Seat Easy Exit	Full Partial Off

   *: On models with the 8-speaker sound system, customization can be performed on the combination meter assembly. On models with the HDD navigation system, if a communication between multi-media module receiver assembly and the combination meter assembly is disrupted, customization can be performed on the combination meter assembly.

4. Warning Mode Function

   
   

   • When a warning is necessary, the warning display interrupts the display in the multi-information display.

   • The master warning light may illuminate or blink and the buzzer in the combination meter assembly may sound depending on the item display on the multi-information display.

   Priority	Indication/Warning	Master Warning Light	Buzzer
   1	Maintenance Mode	-	-
   	Certification Mode	-	-
   	Adjusting LDA Camera*1	-	-
   	Adjusting Front Radar Beam*2, *3	-	-
   	Checking Cruise Control C/D*2	-	-
   	Checking Cruise Control Brake*2	-	-
   	BRAKE!*3	-	-
   2	Vehicle approaching warning during dynamic radar cruise control*2	-	-
   	Lane Departure Alert*1	-	-
   3	Door Open (While Driving)*4	Blinks	Sounds
   	Door Open	-	-
   	Clearance Sonar Obstruction Detection*5	-	-
   	Check Park Sonar System*5	Illuminates	-
   	Clean Park Sonar*5	Illuminates	-
   4	Auto Power OFF to Conserve Battery	-	-
   5	Shift to P position	Blinks	Sounds
   	Shift to P position when parked	Blinks	Sounds
   6	Check Power Steering System	Illuminates	Sounds
   	Release Parking Brake	Blinks	Sounds
   	Key not detected	Blinks	Sounds
   	Speed Limit Exceeded	Blinks	-
   7	Engine coolant temperature warning	Illuminates	Sounds
   	Clean Radar Sensor*2, *3	Illuminates	Sounds
   	Cruise Control not available*2	Illuminates	Sounds
   	LDA not available*1	Illuminates	Sounds
   	Check Entry & Start System	Blinks	Sounds
   	BSM not available*6	Illuminates	Sounds
   	Check Cruise Control System	Illuminates	Sounds
   	Check LDA System*1	Illuminates	Sounds
   	Check PCS System*3	Illuminates	Sounds
   	Check BSM System*6	Illuminates	Sounds
   	Engine Oil Pressure Low	Illuminates	Sounds
   8	Dynamic Radar Cruise Control and Lane Departure Alert on*1, *2	-	-
   	Turn Power OFF	Blinks	Sounds
   	Key detected in vehicle	Blinks	Sounds
   	Turn Lights Off	Blinks	Sounds
   	Moon Roof opened*7	Blinks	Sounds
   	Window opened	Blinks	Sounds
   	Window/Moon Roof opened*7	Blinks	Sounds
   	Depress brake pedal touch engine switch with key	Blinks	Sounds
   	Depress brake pedal and push engine switch to start	Blinks	Sounds
   	Shift to P position to Start	Blinks	Sounds
   9	Steering Lock active	Blinks	Sounds
   	Shift to P position when starting	Blinks	Sounds
   10	Key Battery Low	Illuminates	Sounds
   	Engine Oil Level Low	Illuminates	Sounds
   	Check AHB System*8	Illuminates	Sounds
   	Tire inflation pressure display	-	-
   11	Washer Fluid Low	-	-
   	Fuel Low	-	-
   	TRC OFF	-	-
   	Turn on the high beam to activate AHB System*8	-	-
   	POWER ON	-	-
   	Engine start ready state	-	-
   	Door unlock mode change display	-	Sounds
   	PCS temporarily not available*3	-	-
   	Theft Sensor OFF*9	-	-
   	Theft Sensor ON*9	-	-

   
   

   • *1: Models with lane departure alert system

   • *2: Models with dynamic radar cruise control system

   • *3: Models with pre-crash safety system

   • *4: If the vehicle has reached a speed of 5 km/h (3 mph)

   • *5: Models with LEXUS parking assist-sensor system

   • *6: Models with blind spot monitor system

   • *7: Models with sliding roof system

   • *8: Models with automatic high beam system

   • *9: Models with intrusion sensor