LIGHTING SYSTEM


  1. OUTLINE


    1. Exterior Light


      1. The exterior lights consist of the following lights:

        A0046B3C01
        *A Models with Projector Headlight *B Models with Projector Headlight w/ LED Daytime Running Light/LED Clearance Light
        *C Models with Front Fog Light - -
        *1 Side Turn Signal Light *2 Fog Light Assembly RH
        *3 Headlight Assembly RH *4 Headlight Assembly LH
        *5 Fog Light Assembly LH *6 Daytime Running Light/Clearance Light
        *7 Front Turn Signal Light *8 Headlight (High/Low Beam)
        *9 LED Daytime Running Light/LED Clearance Light - -
        *a The illustrations shown are examples only. - -
        A0046BNC01
        *A Models with Bulb Type Stop Light *B Models with LED Type Stop Light
        *1 Center Stop Light Assembly *2 Rear Combination Light Assembly RH
        *3 Rear Light Assembly RH *4 License Plate Light Assembly
        *5 Rear Light Assembly LH *6 Rear Combination Light Assembly LH
        *7 Rear Turn Signal Light *8 Stop Light/Taillight
        *9 Back-up Light *10 Rear Fog Light (Oncoming Lane Side Only)
        *11 Taillight *12 Stop Light
        *a The illustrations shown are examples only. - -

    2. Daytime Running Light System


      1. The daytime running light system is designed to automatically illuminate the daytime running light during the daytime to keep the vehicle highly visible to other vehicles.

    3. Automatic Light Control System


      1. When the light control switch is in the AUTO position, the automatic light control sensor detects the ambient light level and automatically turns the headlights, taillights, clearance lights and license plate lights on or off accordingly.

    4. Light Automatic Turn-off System


      1. The light auto turn-off system is used to prevent the driver from leaving the vehicle with the headlights, front fog lights, clearance lights, taillights, rear fog light or license plate lights on.

    5. Follow Me Home System


      1. The follow me home system is designed to illuminate the low beam headlights for approximately 30 seconds after the vehicle is parked.

    6. Light Reminder System


      1. When the driver door is opened with either the headlights or the taillights turned on when the ignition switch is turned off, the buzzer sounds to prevent the driver from forgetting to turn off the lights.

    7. Manual Headlight Beam Level Control System


      1. The manual headlight beam level control system keeps the beam of the headlight adjusted.

    8. Automatic High Beam System (Models with Toyota Safety Sense)


      1. The automatic high beam system detects lights in front of the vehicle and automatically changes between high beams and low beams to support the driver during night driving.

  2. SPECIFICATION


    1. Exterior Light

      Light Type Wattage
      Headlight Assembly*1 Low Beam/High Beam HIR2 Bulb 55
      Front Turn Signal Light WY21W Bulb 21
      Daytime Running Light/Clearance Light W21/5W Bulb 21/5
      Headlight Assembly*2 Low Beam/High Beam HIR2 Bulb 55
      Front Turn Signal Light WY21W Bulb 21
      Daytime Running Light/Clearance Light LED 20/2.5
      Front Fog Light Assembly*3 H16 Bulb 19
      Side Turn Signal Light Assembly WY5W Bulb 5
      Rear Combination Light Assembly*4 Taillight/Stop Light P21/5W Bulb 21/5
      Rear Turn Signal Light WY21W Bulb 21
      Rear Light Assembly*4 Back-up Light W16W Bulb 16
      Rear Fog Light LED 3.0
      Rear Combination Light Assembly*5 Taillight LED 1.1
      Stop Light LED 2.0
      Rear Turn Signal Light WY21W Bulb 21
      Rear Light Assembly*5 Taillight LED 1.9
      Back-up Light W16W Bulb 16
      Rear Fog Light LED 3.0
      Center Stop Light Assembly LED 0.4
      License Plate Light Assembly W5W Bulb 5

      *1: Models with projector headlight

      *2: Models with projector headlight w/ LED daytime running light/LED clearance light

      *3: Models with front fog light

      *4: Models with bulb type stop light

      *5: Models with LED type stop light

  3. PRECAUTION


    1. Automatic High Beam System (Models with Toyota Safety Sense)


      1. The automatic high beam system is a system that helps ensure visibility by automatically turning the high beams on and off.

      2. However, due to control limitations of the automatic high beam system, it may be necessary to manually turn the high beams on and off. When driving, for safety reasons, make sure to change the high beams and low beams manually according to the driving conditions.

      3. Under the following conditions, the automatic high beam system might not detect other vehicles or lights correctly, or the high beams might cause glare or flash pedestrians or the occupants of other vehicles. Manual operation should be used.

        Factor Condition
        Weather/Climate When driving in bad weather (rain, snow, fog, sandstorms, etc.).
        Windshield Glass

        • When the windshield glass is not clear (ice, snow or frost on the glass).

        • When the windshield glass is dirty (sand, mud, water stains or bugs on the glass).

        • When the windshield glass is cracked.

        • When the windshield glass is fogged-up.

        • When the windshield glass has a film attached.

        • When an object on the instrument panel reflects off of the windshield glass.

        • When any other abnormal conditions exist with the windshield glass.
        Pre-crash Safety City Sensor (Monocular Camera Sensor)

        • When a parking tag, magnifying lens or other accessory is mounted on the pre-crash safety city sensor.

        • When the pre-crash safety city sensor or its built-in monocular camera sensor is deformed.

        • When the monocular camera sensor in the pre-crash safety city sensor is dirty.

        • When any other abnormal conditions exist with the pre-crash safety city sensor or its built-in monocular camera sensor.
        Nearby Vehicles or Lights

        • When lights similar to headlights or taillights are in the vicinity of the vehicle.

        • When a nearby vehicle has no lights or its lights are off.

        • When a vehicle in front has misaligned lights, or its lights are changing color.

        • When a vehicle in front has extremely dirty headlights or taillights.
        Road Conditions

        • When driving in an area where the conditions often change between bright and dark.

        • When driving on a road with many uphill and downhill slopes.

        • When driving on a winding road or around a sharp curve.

        • When driving on a bumpy road (cobblestone pavement, gravel road, rough unpaved road, etc.).

        • When highly reflective objects are in front of the vehicle (mirrors, road signs, etc.).
        Vehicle Conditions

        • When the headlights are damaged, deformed or dirty.

        • When the vehicle posture is abnormal due to flat tire (or posture has changed due to the vehicle being fully loaded, a trailer being towed, etc.).

        • When the vehicle has other malfunctions or if the vehicle has been modified.
        Automatic High Beam System

        Malfunction:


        • When the automatic high beam indicator light color on the combination meter assembly is amber.

        Others:


        • When the Automatic High Beam system does not seem to be changing between the high beams and low beams properly.

        • When the Automatic High Beam system is frequently changing between the high beams and low beams.

        • When the glare from the high beams would disturb pedestrians or the drivers of other vehicles.

    2. Ignition Switch Expressions


      1. The type of ignition switch used on this model differs depending on the specifications of the vehicle. The expressions listed in the table below are used in this section.

        Expression Ignition Switch (Position) Power Switch (Condition)
        Ignition Switch off LOCK Off (Lock)
        Ignition Switch ACC ACC On (ACC)
        Ignition Switch ON (IG) ON (IG) On (IG)
        Ignition Switch ON (READY) ON (READY) On (Ready)