METER / GAUGE SYSTEM


  1. OPERATING CONDITION


    1. Hybrid System Indicator


      1. Hybrid System Indicator is activated when the following conditions are met.

        Condition Turn the ignition switch to ON (IG).
        READY ON state.
        The shift position is in D or B.

  2. SYSTEM CONTROL


    1. Front Seat Belt Warning


      1. When the ignition switch is ON (IG), this system detects the condition of the seat belts based on the signals from the front seat belt buckle switch LH and RH and the occupant detection sensor.

      2. The front seat belt warning light located in the combination meter assembly is used for both the driver and passenger seats.

      3. After the ignition switch is turned ON (IG), if the driver or front passenger has not fastened their seat belt, the front seat belt warning light will begin flashing.

      4. When the seat belt remains unfastened and the vehicle speed reaches approximately 20 km/h (12.4 mph), the seat belt warning buzzer will start sounding intermittently. At this time, the front seat belt warning light flashing will change in sync with the intermittent buzzer sound. These buzzer and indicator warnings will continue for approximately 30 seconds until the seat belt is fastened.

      5. If the seat belt still remains unfastened over the approximately 30 seconds, the intervals of the intermittent buzzer sound and flashing light will change, and such warnings will continue for approximately 90 seconds until the seat belt is fastened.

      6. While the front seat belt warning light and buzzer are operating, fastening the seat belt will bring them to a stop.

    2. Rear Seat Belt Warning


      1. When any one of the rear seat belt LH, the rear seat belt center or the rear seat belt RH is not fastened, the rear seat belt warning system will turn on the rear seat belt warning light and buzzer provided in the combination meter assembly to urge rear passengers to fasten the rear seat belts.

      2. The rear seat belt warning light will turn on when approximately 30 seconds have elapsed after the ignition switch is turned to ON (IG) and a rear door is operated from open to close, or a rear seat belt is unfastened while the ignition switch is ON (IG).

      3. The rear seat belt warning buzzer will sound when the vehicle speed reaches approximately 20 km/h (12.4 mph) or more while the rear seat belt warning light is on. If the rear seat belt is not then fastened after approximately 30 seconds have elapsed since the buzzer started sounding, the rear seat belt warning buzzer will sound more loudly than normal for approximately 90 seconds.

  3. FUNCTION


    1. Hybrid System Indicator


      1. Hybrid System Indicator displays the total of the HV battery and engine output as the hybrid system output.

      2. The scale for Hybrid System Indicator consists of the 3 indicators (Charge, Eco, Power). The role of each indicator is as follows.

        A01UWSGE01
        Indicator Function
        *1 Charge (CHG) This shows that energy regeneration is occurring.
        *2 Eco This indicator is active while the vehicle is driven eco-friendly.
        *3 Eco (Hybrid Eco) This indicator shows that the vehicle is driven in a manner that promotes frequent motor only operation (Based on the driving conditions, the power management control ECU determines if the engine should be stopped to enhance fuel efficiency.).
        *4 Power (PWR) This indicator is on while the drive power is exceeding the eco-friendly driving range (during full power driving etc.).

    2. Buzzer Function


      1. The table below shows the buzzer in the combination meter assembly:

        Item

        • READY

        • Front Seat Belt Warning

        • Rear Passengers Seat Belt Warning

        • Brake System Warning

        • EPS Warning

        • Door Open Warning When Not in P Position*

        • Entry and Start System Warning*

        • Key Reminder

        • Accelerator Depression with Neutral (N) Selected

        • Hybrid System Warning

        • HV Battery Low Warning

        • Engine Immobiliser Matching Completion Report

        • Parking Brake On Driving Warning

        • Door Open Driving Warning

        • EV Drive Mode Reject Warning

        • Light Reminder

        • Turn Flasher Sound

        • *: Models with entry and start system

    3. Multi-information Display Function

      A01UX4AE01
      Text in Illustration
      *1 Multi-information Display - -
      Display Area Display Display Item Outline
      "a" A01UX2A Clock Display The clock is always displayed.
      "b" A01UX14 Outside Temperature Display The outside temperature is always displayed.
      "c" A01UX59 Odometer Display Displays the odometer.
      A01UWZN Trip Meter A Display Displays the trip meter A.
      A01UX2L Trip Meter B Display Displays the trip meter B.
      A01UX0P Instantaneous Fuel Consumption Display

      • Displays the value that has been calculated by the combination meter assembly, which is based on the distance driven and the fuel consumption volume.

      • This display is updated constantly.
      A01UX4E Total Average Fuel Consumption

      • Displays the value, calculated by the combination meter assembly, which is based on the distance driven and the fuel consumption volume.

      • The value will be reset by pressing and holding the ODO/TRIP DISP switch.

      • This display is updated every 10 seconds.
      A01UX83 Drivable Distance Display

      • Displays the value that has been calculated by the combination meter assembly, which is based on the elapsed time and distance driven after the ignition switch, has been turned to ON (READY).

      • This display is updated every 1 second.
      A01UWU8 Average Vehicle Speed After Starting Display

      • Displays a value that has been calculated by the combination meter assembly based on the vehicle speed signal and the elapsed time since the READY ON signal.

      • This display is updated every 10 seconds.
      A01UX7Y Dimming Mode Display Adjust the meter luminance.
      "d" A01UWRU Shift Position Indicator Displays shift position P, R, N, D or B.

  4. OPERATION


    1. Switching the Multi-information Display


      1. The multi-information display changes in the order shown below by pressing the ODO/TRIP DISP switch.

        A01UWZCE02
        Text in Illustration
        *1 ODO/TRIP DISP Switch *2 Odometer Display
        *3 Trip Meter A Display *4 Trip Meter B Display
        *5 Instantaneous Fuel Consumption Display *6 Average Fuel Consumption After Refueling Display
        *7 Drivable Distance Display *8 Average Vehicle Speed After Starting Display
        *9 Dimming Mode Display (While Taillights ON) - -
        A01UWXO Pressing the ODO/TRIP DISP switch - -

    2. Dimming Mode Display Function


      1. The brightness level of the combination meter assembly can be displayed on the multi-information display to adjust the meter luminance.

      2. While the dimming mode is displayed, the brightness of the meter can be changed by pressing the ODO/TRIP DISP switch for 1 second or more. The brightness of the meter can be adjusted in 4 levels.

        A01UWW0E02
        Text in Illustration
        *1 ODO/TRIP DISP Switch *2 100%
        *3 50% *4 25%
        *5 12.5% - -
        *a Meter Brightness - -