METER / GAUGE SYSTEM


  1. OPERATING CONDITION


    1. Eco Driving Indicator


      1. The Eco Driving Indicator starts to operate when the following conditions are met:

        Condition Ignition switch (engine switch*) is ON.
        Engine is running.
        Shift lever is in D.
        Drive mode is normal.
        Shift paddle switch (transmission shift switch assembly) is not being operated.
        Vehicle is running.

        • *: Models with entry and start system

      2. The Eco Driving Indicator stops operation when the following conditions are met:

        Condition Ignition switch (engine switch*) is off.
        Shift lever is in any position other than D.
        Drive mode is in any other mode except normal.
        Shift paddle switch (transmission shift switch assembly) has been operated.

        • *: Models with entry and start system

  2. FUNCTION


    1. Buzzer Function


      1. The table below shows the warning and reminder functions of the buzzer in the combination meter assembly:

        Item

        • Pre-collision Warning

        • Multi-information Display Warning Mode Indication

        • Front Seat Belt Warning

        • Door Open Driving Warning

        • Entry and Start System Warning

        • Engine Immobiliser System Warning

        • Power Steering Warning

        • VSC/Active Test

        • Stop and Start System Warning

        • Speed Warning

        • LDA Warning

        • Parking Brake Unreleased Warning

        • Downshift Reject Warning

        • Key Reminder

        • Rear Passengers Seat Belt Reminder

        • Light Reminder System

        • Hill-start Assist Control (Set)

        • Hill-start Assist Control (Reset)

        Tech Tips

        The buzzer function differs by vehicle specification.

    2. Multi-information Display


      1. The multi-information display has 4 displays*1 or 5 displays*2.

      2. The multi-information display can be switched by pressing the DISP switch located on the steering pad.

      3. The multi-information display shows the following:

        Display Outline
        Ambient Temperature and Date The ambient temperature and date are displayed.
        Cruise Information In the cruise information display, 5 types of information (current fuel consumption, average fuel consumption, driveable distance, average vehicle speed, elapsed time) can be displayed.
        Warning The warning display will interrupt the multi-information display immediately when a warning occurs.
        Eco Driving Indicator Zone*2 Eco driving ratio based on accelerator pedal operation is shown with a bar graph.
        Setup The clock, date, language, Eco Driving Indicator Light*2, and units can be set up from this screen. This setup is available only while the vehicle is stopped. If vehicle movement is detected during setup, the setup will be canceled automatically.

        • *1: Models without Eco Driving Indicator

        • *2: Models with Eco Driving Indicator

      4. The dimming mode display which displays on multi-information display, can be switches by pressing the light control rheostat switch located on the instrument panel.

        A002JPIE02
        A002K1BE02
        A002K2TE02
        A002JQXE02
        A002K97E02
        A002K80E02
        A002JYDE02
        A002JZKE02
        A002JWKE02
        A002K74E02
        A002JW8E02
    3. Cruise Information Display Function


      1. The cruise information is displayed in the following order each time the DISP switch is pressed:

        Item Displayed Content Outline
        Current Fuel Consumption km/l A002K1G
        • Displays the value that has been calculated by the meter ECU, which is based on the driven distance and the fuel consumption volume (fuel injection amount signal from ECM via CAN), provided that the ignition switch (engine switch*) is turned to ON.

        • The display updates every 0.6 seconds.

        mpg A002JVS
        l/100km A002JW1
        Average Fuel Consumption km/l A002K27
        • Displays the value that has been calculated by the meter ECU, which is based on the driven distance and the fuel consumption volume (fuel injection amount signal from ECM via CAN).

        • The value can be reset by pressing the DISP switch for 0.8 seconds or more.

        • The display updates every 10 seconds.

        mpg A002K0M
        l/100km A002K1K
        Driveable Distance km A002K9B
        • Displays the value that has been calculated by the meter ECU, which is based on the fuel consumption data that the meter ECU continuously monitors and stores in its memory, and the residual fuel volume data, provided that the ignition switch (engine switch*) is turned to ON.

        • The display updates every kilometer or mile.

        miles A002JOV
        Average Vehicle Speed km/h A002K0H
        • Displays the value that has been calculated by the meter ECU, which is based on the elapsed time and driven distance after the ignition switch (engine switch*) is turned to ON or the DISP switch has been pressed for 0.8 seconds or more.

        • The display updates every 10 seconds.

        MPH A002JQH
        Elapsed Time A002JU5 Displays the time that has elapsed since the ignition switch (engine switch*) has been turned to ON or the DISP switch has been pressed for 0.8 seconds or more.

        • *: Models with entry and start system

    4. Warning Display Function

      Warning Message Description Master Warning Light Buzzer
      A002K4N Door Open Off Off
      A002JXH Back Door Open Off Off
      AUTO POWER OFF TO CONSERVE BATTERY Auto Power Off Operation Condition Off Off
      SHIFT TO P POSITION Shift Position Warning Blinks Off
      SHIFT TO P POSITION AND PUSH ENGINE SWITCH TO TURN POWER OFF Power Off Operation Guide Blinks Sounds
      RELEASE PARKING BRAKE Vehicle is traveling with the parking brake engaged. Blinks Off
      KEY NOT DETECTED No Key Warning Blinks Off
      CHECK CLUTCH SWITCH Clutch Switch Malfunction3 Illuminates Sounds
      TRC OFF TRC OFF - -
      CHECK SPEED LIMITER SYSTEM Speed Limiter Control Malfunction Illuminates Sounds
      CHECK CRUISE CONTROL SYSTEM Cruise Control System Malfunction Illuminates Sounds
      CHECK STEERING LOCK SYSTEM Check Steering Lock System Illuminates Sounds
      ENGINE OIL PRESSURE LOW Low Engine Oil Pressure Illuminates Sounds
      HIGH TRANSMISSION FLUID TEMPERATURE High Transmission Fluid Temperature Illuminates Sounds
      TURN POWER OFF Prompt to Turn Power Off Blinks Sounds
      KEY DETECTED IN VEHICLE Key Detected in Vehicle Blinks Sounds
      TURN LIGHTS OFF The ignition switch (engine switch) is turned off and the driver door is opened with the light control switch in the TAIL or HEAD position. Blinks Off
      DEPRESS BRAKE PEDAL, TOUCH ENGINE SWITCH WITH KEY Start Operation Guide Blinks Sounds
      DEPRESS CLUTCH PEDAL, TOUCH ENGINE SWITCH WITH KEY Start Operation Guide Blinks Sounds
      DEPRESS BRAKE PEDAL AND PUSH ENGINE SWITCH TO START Start Operation Guide Blinks Off
      DEPRESS CLUTCH PEDAL AND PUSH ENGINE SWITCH TO START Start Operation Guide Blinks Off
      SUPPORT PEDAL OPERATION
      SHIFT TO P POSITION TO START Start Operation Guide Blinks Sounds
      STEERING LOCK ACTIVE Steering lock has not been released. Blinks Sounds
      KEY BATTERY LOW Low Key Battery Warning Illuminates Sounds
      DRAIN WATER FROM FUEL FILTER Some moisture has been detected in the fuel filter Illuminates Sounds
      REPLACE FUEL FILTER The fuel filter is clogged. Illuminates Sounds
      OIL MAINTENANCE REQUIRED SOON Engine Oil Maintenance Off Off
      OIL MAINTENANCE REQUIRED Engine Oil Maintenance Off Off
      RESETTING OIL MAINTENANCE DATA Engine Oil Maintenance Off Off
      DPF FULL ENGINE SERVICE REQUIRED There is a malfunction in the exhaust gas purification device. Off Off
      DPF FULL SEE OWNER'S MANUAL There is a malfunction in the exhaust gas purification device. Off Off
      DPF MANUAL REGENERATION IN PROCESS Soot caught in the exhaust gas purification device needs to be manually combusted. Off Off
      [VSC] 88 88 88 88 A8 CD EF Diagnosis Off Off
      BRAKE! A warning of collision risk has been issued. Off Sounds
      PRE-COLLISION SYSTEM MALFUNCTION VISIT YOUR DEALER Pre-collision System Malfunction Illuminates Sounds
      PRE-COLLISION SYSTEM TURNED OFF Pre-collision System Off Off Off
      PRE-COLLISION SYSTEM UNAVAILABLE Battery voltage is low Off Off
      VSC TURNED OFF PRE-COLLISION BRAKE SYSTEM UNAVAILABLE Pre-collision brake operation is stopped due to VSC being turned OFF. Off Off
      FRONT CAMERA UNAVAILABLE The system is temporarily stopped due to the front camera overheating. Off Off
      FRONT CAMERA VISION BLOCKED. CLEAN AND DEMIST WINDSHIELD Obstacles are detected due to the glass ahead of the front camera being dirty. Off Off
      CHECKING PRE-COLLISION BRAKE The system has been switched to the test mode. Off Off
      CHECK LDA SYSTEM LDA System Malfunction Illuminates Sounds
      ADJUSTING FRONT CAMERA The system has been switched to the test mode. Off Off
      LDA SYSTEM IS UNAVAILABLE BELOW APPROX. 50km/h The vehicle speed has dropped below a specified value during LDA operation. Off Off
      LDA SYSTEM IS UNAVAILABLE BELOW APPROX. 32MPH The vehicle speed has dropped below a specified value during LDA operation. Off Off
      LDA SYSTEM IS UNAVAILABLE AT THIS SPEED The vehicle speed exceeds LDA system operation speed range. Off Off
      LDA OFF LDA System Off Off Off
      HEADLIGHT SYSTEM MALFUNCTION. VISIT YOUR DEALER Headlight System Malfunction Illuminates Sounds

      Tech Tips

      The items displayed differ by vehicle specification.

    5. Eco Driving Indicator


      1. The operating diagram of the Eco Driving Indicator is as follows:

        A002JRRE16
      2. When the ECM, using information (such as vehicle speed, accelerator pedal depressed volume, shift lever position, engine speed signal (engine RPM data), shift range, drive mode, and so on), calculates Eco driving, it turns on the Eco Driving Indicator Light and shows the bar graph of the Eco Driving Indicator Zone Display within the Eco Driving range.

      3. When the ECM calculates that the driving is not fuel-efficient, it turns off the Eco Driving Indicator Light and blinks the right side of the Eco Driving Indicator Zone Display.

      4. The operation of the Eco Driving Indicator is as follows:

        Vehicle Condition Eco Driving Indicator Zone Display Eco Driving Indicator Light
        Stopped A002K0W Off
        Eco Driving A002K9AE01
        *1 Zone of Eco driving
        *2 Eco Driving Ratio Based on Accelerator Pedal Operated.
        Illuminates
        Non-Eco Driving A002K64 Off
      5. The Eco Driving Indicator Light can be turned off:


        • From the Eco Driving Indicator Light setting display of the multi-information display.

    6. Front Seat Belt Warning Function


      1. When the ignition switch (engine switch*) is ON, this system detects the condition of the seat belts based on the signals from the driver and front passenger seat belt buckle switches and the occupant detection sensor.

      2. The buzzer sounds when the vehicle speed exceeds 20 km/h (12.4 mph) to emphasize the fact that the seat belt is unbuckled. After 30 seconds, the sound changes for emphasis. The sound continues for 90 seconds. Once a buzzer begins to sound, it will continue until the seat belt is buckled or the ignition switch (engine switch*) is turned off.


        • *: Models with entry and start system

        Tech Tips

        Upon receiving a request from a user who cannot wear a seat belt for a special reason, the buzzer warning can be canceled using the intelligent tester II. For details, refer to the Repair Manual.

      3. Occupant Detection Sensor


        • The occupant detection sensor, which is enclosed in the seat cushion of the front passenger seat, is used to detect whether or not the front passenger seat is occupied.

        • This sensor consists of a construction in which 2 electrode sheets sandwich a spacer. When the occupant is seated, the electrode sheets come in contact with each other through the hole provided in the spacer portion, thus enabling the current to flow.

        • In this way, the sensor detects whether or not an occupant is seated in the front passenger seat.

    7. Rear Passengers Seat Belt Reminder Function

      A002JQ4E01
      *1 Rear Passengers Seatbelt Reminder Light
      *2 Telltale Marker

      1. If the meter ECU receives an off signal from the rear door courtesy light switch assembly when the ignition switch (engine switch*) is ON, a rear passengers seat belt reminder light is shown on the telltale light assembly. At this time, if the meter ECU receives an on signal from a rear seat 3 point type inner belt assembly, rear seat inner belt assembly, or rear No. 2 seat belt sub-assembly, it will extinguish the telltale marker on the reminder light corresponding to the rear seat 3 point type inner belt assembly, rear seat inner belt assembly, or rear No. 2 seat belt sub-assembly which sent the on signal. In addition, the rear passengers seat belt reminder light will automatically turn off approximately 30 seconds after the reminder light is turned on.

      2. If any of the rear seat belts are released while the vehicle speed is above 20 km/h (12 mph), the rear passengers seat belt reminder light is shown and the buzzer is sounded. After 30 seconds, the sound is changed for emphasis. The sound continues for 90 seconds. Once the buzzer begins to sound, it will continue until the rear seat belt is buckled or the ignition switch (engine switch*) is turned off.


        • *: Models with entry and start system

  3. FAIL-SAFE


    1. Eco Driving Indicator


      1. When any of the following conditions are met, the Eco Driving Indicator Light is turned off and the Eco Driving Indicator Zone Display is stopped:


        • Engine Signal Malfunction

        • CAN Signal Malfunction