METER / GAUGE SYSTEM


  1. OPERATING CONDITION


    1. Eco Driving Indicator Light (Models with CVT)


      1. Eco Driving Indicator Light starts to operate when all of the following conditions are met:

        Condition Ignition switch is ON.
        Engine is running.
        Shift lever is in D.
        Shift paddle switch is not operating.
        Driving mode is normal.
        When the vehicle is at a speed of about 130 km/h (81 mph) or below.

      2. Eco Driving Indicator Light stops operation when any of the following conditions is met:

        Condition Ignition switch is off.
        Engine is stopping.
        Shift lever is in any position other than D.
        Shift paddle switch is operating.
        Driving mode is not normal.
        When the vehicle is at a speed of about 130 km/h (81 mph) or over.

  2. SYSTEM CONTROL


    1. Front Seat Belt Warning


      1. When the ignition switch is ON, this system detects the condition of the seat belts based on the signals from the front seat belt buckle switch LH and RH and the weight detector sensors.

      2. The front seat belt warning light located in the combination meter is used for both the driver and passenger seats.

      3. After the ignition switch is turned ON, if the driver or front passenger has not fastened their seat belt, the seat belt warning light will begin flashing.

      4. When the seat belt remains unfastened and the vehicle speed reaches approximately 20 km/h (12.4 mph), the seat belt warning buzzer will start sounding intermittently. At this time, the seat belt warning light flashing will change in sync with the intermittent buzzer sound. These buzzer and indicator warnings will continue for approximately 30 seconds until the seat belt is fastened.

      5. If the seat belt still remains unfastened over the approximately 30 seconds, the intervals of the intermittent buzzer sound and flashing light will change, and such warnings will continue for approximately 90 seconds until the seat belt is fastened.

      6. While the seat belt warning light and buzzer are operating, fastening the seat belt will bring them to a stop.

    2. Rear Seat Belt Warning (Models with Rear Seat Belt Warning System)


      1. When any one of the rear seat belt LH, the rear seat belt center or the rear seat belt RH is not fastened, the rear seat belt warning system will turn on the rear seat belt warning light and buzzer provided in the combination meter to urge rear passengers to fasten the rear seat belts.

      2. On 5-door models, the rear seat belt warning light will turn on when approximately 30 seconds have elapsed after the ignition switch is turned to ON and a rear door is operated from open to close, or a rear seat belt is unfastened while the ignition switch is ON.

      3. On 3-door models, the rear seat belt warning light will turn on when approximately 30 seconds have elapsed after the ignition switch is turned to ON, or a rear seat belt is unfastened while the ignition switch is ON.

      4. The rear seat belt warning buzzer will sound when the vehicle speed reaches approximately 20 km/h (12.4 mph) or more while the rear seat belt warning light is on. If the seat belt is not then fastened after approximately 30 seconds have elapsed since the buzzer started sounding, the rear seat belt warning buzzer will sound more loudly than normal for approximately 90 seconds.

    3. Eco Driving Indicator Light (Models with CVT)


      1. The operating diagram of Eco Driving Indicator Light is as follows:

        A0044ZBE01

      2. When the ECM, using information (such as vehicle speed, accelerator pedal depressed volume, engine speed signal (engine rpm data), and so on), calculates that the vehicle is driven in an Eco-friendly manner, it turns on Eco Driving Indicator Light and shows the bar graph of ECO Driving Indicator Zone Display* within Zone of Eco driving.


        • *: Models with color type multi-information display

      3. When the ECM calculates that the acceleration exceeds Zone of Eco driving, it turns off ECO Driving Indicator Light.

      4. The operation of Eco Driving Indicator is as follows:

        Vehicle Condition ECO Driving Indicator Zone Display* Eco Driving Indicator Light
        Stopped A00457S Turns off
        ECO Driving A00458B Turns on
        Non-ECO Driving A0044YU Turns off

        • *: Models with color type multi-information display

      5. Eco Driving Indicator can be deactivated in the following ways: Eco Driving Indicator Light can be deactivated from Eco Driving Indicator Light customization display of the multi-information display.

  3. FUNCTION


    1. Buzzer Function


      1. The table below shows the buzzer in the combination meter assembly:

        Priority Item
        1 Pre-crash Safety System Operation Warning*1
        2 Front Seat Belt Warning (Level 2)
        3 Rear Passengers Seat Belt Warning*2
        4 Front Seat Belt Warning (Level 1)
        5 EPS Warning
        6 Entry and Start System Warning (Continuous)*3
        7 Stop and Start System Warning*4
        8 Entry and Start System Warning (Intermittent)*3
        9 Key Reminder
        10 Speed Limit Exceed Warning*5
        11 Lane Departure Alert Warning*1
        12 Entry and Start System Warning (Intermittent, Maximum 9 times)*3
        13 Entry and Start System Warning (Once)*3
        14 Door Open Driving Warning
        15 Multi-information Display Warning*6
        16 Pre-crash Safety System Malfunction*1
        17 Engine Immobiliser Matching Completion Report
        18 Parking Brake On Driving Warning
        19 Sport Sequential Shift Reject Warning*7
        20 Road Sign Assist Indication*8
        21 Light Reminder
        22 Turn Flasher Sound

        • *1: Models with Toyota safety sense

        • *2: Models with rear seat belt warning system

        • *3: Models with entry and start system

        • *4: Models with stop and start system

        • *5: Models with speed limiter control system

        • *6: Models with color type multi-information display

        • *7: Models with CVT

        • *8: Models with road sign assist system

    2. Multi-information Display Function (Models with Color Type Multi-information Display)


      1. Display Function Flow


        • The multi-information display can be switched as shown in the flowchart below:

        A00456GE01
        No. Condition
        (1) Conditions are not met.
        (2) Conditions are met.
        (3) If there are multiple display requests, items will be displayed in sequence.
        (4) Item or display is selected by operating the steering pad switch assembly switch.
        (5) After ignition switch is turned to ON.
        (6) ODO display is displayed for a certain period of time after the ignition switch is turned off.

      2. Display Tab Operation


        • The information currently displayed can be switched using the LEFT/RIGHT switch on the steering pad switch assembly.

        A0044VTC01
        *A Models with Navigation System *B Models with Display Audio System
        *C Models with Toyota Safety Sense *D Models with Stop and Start System
        *1 Steering Pad Switch Assembly - -
        *a LEFT Switch *b RIGHT Switch
        *c Drive Information Tab *d Navigation Information Tab
        *e Audio Information Tab *f Driving Assist System Information Tab
        *g Stop and Start Information Tab *h Message Tab
        *i Settings Tab *j The illustrations shown are examples only. The illustrations may differ from the actual vehicle screen.
        A0044QS LEFT switch operation A0044Y1 RIGHT switch operation

      3. Drive Information


        • Drive information shows vehicle information such as drivable range, fuel consumption and vehicle speed.

        • The drive information can be switched using the UP/DOWN switch on the steering pad switch assembly.

        A0044PUC01
        *A Models with CVT - -
        *1 Steering Pad Switch Assembly - -
        *a UP Switch *b DOWN Switch
        *c

        After Start Display


        • Average Fuel Consumption after Engine Start-up

        • Average Vehicle Speed after Engine Start-up

        • Elapsed Time after Engine Start-up

        		 *d

        After Reset Display


        • Current Fuel Consumption (Bar Display) between Reset Operations

        • Average Fuel Consumption (Bar Display) between Reset Operations

        • Average Fuel Consumption (Value Display) between Reset Operations

        • Elapsed Time between Reset Operations or Average Vehicle Speed between Reset Operations
        *e

        After Refuel Display


        • Cruising Range after Refueling

        • Average Fuel Consumption after Refueling

        		 *f Eco Driving Indicator Zone Display
        *g Digital Vehicle Speed Display *h Blank
        *i The illustrations shown are examples only. The illustrations may differ from the actual vehicle screen. - -
        A0044QS UP switch operation A0044Y1 DOWN switch operation

      4. Setting Function


        • The items displayed on the multi-information display can be customized.

        • The items can be selected on the information setting screen.

        Lane Departure Alert System (Models with Toyota safety sense)
        Item Available Setting
        Warning Sensitivity

        Alert sensitivity of alert system can be changed:


        • High

        • Standard
        Road Sign Assist (Models with road sign assist system)
        Item Available Setting
        Road Sign Assist

        The road sign assist system can be set to on/off:


        • ON

        • OFF
        Excess Speed

        The excess speed notification method can be changed:


        • No Notification

        • Only Visual

        • Visual and Audible
        Notification Level

        Select to set the speed threshold over which the excess speed warning starts to operate when a speed limit sign is displayed on the multi-information display.


        • 10 km/h

        • 5 km/h

        • 3 km/h
        Others

        The other notification method can be changed:


        • No Notification

        • Only Visual

        • Visual and Audible
        Clock
        Item Available Setting
        Clock Select to adjust time or set a clock format.
        Meter Settings
        Item Available Setting
        Language

        The language used on the multi-information display can be selected:


        • English

        • German

        • French

        • Spanish

        • Italian

        • Portuguese

        • Dutch

        • Swedish

        • Danish

        • Russian

        • Finnish

        • Greek

        • Polish

        • Ukrainian

        • Turkish

        • Hungarian

        • Czech

        • Slovak

        • Romanian
        Unit

        The unit displayed on the multi-information display can be selected:


        • km (km/L)

        • km (L/100 km)

        • miles (MPG)

        The outside temperature unit displayed on the multi-information display can be selected:


        • °C (Celsius)

        • °F (Fahrenheit)
        Eco Driving Indicator Light*1

        The Eco Driving Indicator Light can be switched:


        • ON

        • OFF
        Drive Information

        The drive information of after reset displayed item can be changed:


        • Elapsed Time between Reset Operations

        • Average Vehicle Speed between Reset Operations
        Interruption Display

        The following displays that appear as soon as the set conditions are met can be switched to ON or OFF:


        • Incoming Telephone Display*2

        • Stop and Start Operation Time*3

        • Stop and Start System Status*3
        Initialization The set items can be initialized.

        • *1: Models with CVT

        • *2: Models with display audio system

        • *3: Models with stop and start system

      5. Warning Mode Function


        • When a warning is necessary, the warning display interrupts the display in the multi-information display.

        • The master warning light may illuminate or blink and the buzzer in the combination meter assembly may sound depending on the item displayed on the multi-information display.

        Priority Display Message Master Warning Light Buzzer
        1 ADJUSTING FRONT CAMERA*1 - -
        CHECKING PRE-CRASH BRAKE*1 - -
        BRAKE!*1 - -
        2 Auto power off to conserve battery.*2 - -
        3 Shift to P position.*2 Blinks Sounds
        4 Stop & Start system malfunction. Visit your dealer.*3 Blinks Sounds
        Key not detected.*2 Blinks Sounds
        5 Charging system malfunction. Stop in a safe place. See owner's manual. Illuminates -
        6 Check entry & start system.*2 Blinks Sounds
        Check cruise control system.*4 Illuminates Sounds
        Check speed limiter system.*5 Illuminates Sounds
        LDA system malfunction. Visit your dealer.*1 Illuminates Sounds
        Pre-crash safety malfunction. Visit your dealer.*1 Illuminates Sounds
        Engine oil pressure low. Illuminates Sounds
        Check RSA system.*6 Illuminates Sounds
        LDA system is unavailable below approx. 50km/h.*1 - -
        LDA system is unavailable below approx. 32MPH.*1 - -
        LDA system is unavailable at this speed.*1 - -
        7 Turn power OFF.*2 Blinks Sounds
        Key detected in vehicle.*2 Blinks Sounds
        Turn lights OFF. Blinks Sounds
        Depress brake pedal, touch ENGINE switch with key.*2, *7 Blinks Sounds
        Depress clutch pedal. touch ENGINE switch with key.*2, *8 Blinks Sounds
        Depress brake pedal and push ENGINE switch to start. *2, *7 Blinks Sounds
        Depress clutch pedal and push ENGINE switch to start. *2, *8 Blinks Sounds
        Stop & Start system active. Shift to N and depress clutch to restart.*3, *8 - -
        Shift to P position to start.*2 Blinks Sounds
        8 Steering lock active.*2 Blinks Sounds
        9 Key battery low.*2 Illuminates Sounds
        Drain water from fuel filter.*9 Illuminates Sounds
        Engine oil low. Illuminates Sounds
        Headlight system malfunction. Visit your dealer.*1 Illuminates Sounds
        DPF full, engine service required.*9 Illuminates -
        10 Roads may be icy. Drive with care. - Sounds
        TRC off - -
        Oil Maintenance required soon.*9 - -
        Oil Maintenance required.*9 - -
        To activate AHB, switch headlights to high beam.*1 - -
        Resetting oil maintenance data.*9 - -
        Resetting of oil maintenance data incomplete.*9 - -
        Power on*2 - -
        VSC turned off. Pre-crash brake system unavailable.*1 - -
        Pre-crash safety unavailable*1 - -
        Front camera unavailable*1 - -
        Front camera vision blocked. Clean and demist windshield.*1 - -
        DPF full. See owner's manual.*9 - -
        DPF manual regeneration in process.*9 - -
        Pre-crash safety turned off*1 - -

        • *1: Models with Toyota safety sense

        • *2: Models with entry and start system

        • *3: Models with stop and start system

        • *4: Models with cruise control system

        • *5: Models with speed limiter control system

        • *6: Models with road sign assist system

        • *7: Models with CVT

        • *8: Models with manual transaxle

        • *9: Models with 1ND-TV engine

    3. Multi-information Display Function (Models with Monochrome Type Multi-information Display)


      1. The monochrome type multi-information display can indicate as below:

        A0044ZSC01
        *A No shift position indicator is provided in the combination meter without the tachometer *B No shift position indicator is provided in the combination meter with the tachometer
        *C Shift position indicator is provided in the combination meter with the tachometer - -
        *1 Multi-information Display - -

        • Display Area "a"

          Display Display Item Outline
          A0044NY Clock Display The clock is always displayed.

        • Display Area "b"

          Display Display Item Outline
          A00453F Outside Temperature Display The outside temperature is always displayed.

        • Display Area "c"

          Display Display Item Outline
          A0044O5 Odometer Display Displays the odometer.
          A0044Z9 Trip Meter A Display Displays the trip meter A.
          A0044S3 Trip Meter B Display Displays the trip meter B.
          A0044MC Eco Time Display*1 Displays the total amount of engine stoppage time occurring between ignition switch is ON and the subsequent off.
          A0044YC Eco Odometer Display*1 Displays the total amount of engine stoppage time occurring since the last reset.
          A00451X Instantaneous Fuel Consumption Display

          • Displays the value that has been calculated by the combination meter assembly, which is based on the distance driven and the fuel consumption volume.

          • This display is updated constantly.
          A0044TB Average Fuel Consumption After Refueling Display

          • Displays the value that has been calculated by the combination meter assembly, which is based on the distance driven after refueling and the fuel consumption.

          • The combination meter assembly resets the value when determining that the vehicle has been refueled according to the signal from the fuel sender gauge.

          • This display is updated every 10 seconds.
          A0044PY Drivable Distance Display

          • Displays the value that has been calculated by the combination meter assembly, which is based on the elapsed time and distance driven after the ignition switch, has been turned to ON.

          • This display is updated every 1 second.
          A0044N1 Average Vehicle Speed After Starting Display

          • Displays a value that has been calculated by the combination meter assembly based on the vehicle speed signal and the elapsed time since the engine start signal.

          • This display is updated every 10 seconds.
          A00451Y Speed Limiter Control Mode Display*2 Displays the state of the speed limiter control mode by operating speed limiter main switch.
          A0044OD Pre-crash Safety Warning Timing Display*3 Displays the state of the pre-crash safety warning timing by operating pre-crash system cancel switch assembly.
          A004592 Dimming Mode Display Adjust the meter luminance.
          A00450T A0044MJ Eco Driving Indicator Light Customizing Display*4 Customize Eco Driving Indicator Light.

          *1: Models with stop and start system

          *2: Models with speed limiter control system

          *3: Models with Toyota safety sense

          *4: Models with CVT

        • Display Area "d"

          Display Display Item Outline
          A00454T Shift Position Indicator* Displays shift position P, R, N, D or B of the CVT.

          *: Models with CVT

        • Display Area "e"

          Display Display Item Outline
          A00457D Fuel Gauge Display Displays the remaining fuel amount.

      2. Switching the Multi-information Display Function


        • The display area "c" changes in the order shown below by pressing the ODO/TRIP DISP switch.

          A0044KKC01
          *A Models with CVT *B Models with Stop and Start System
          *1 ODO/TRIP DISP Switch *2 Eco Driving Indicator Light Customizing Display: Eco On.
          *3 Eco Driving Indicator Light Customizing Display: Eco Off. *4 Odometer Display
          *5 Trip Meter A Display *6 Trip Meter B Display
          *7 Eco Time Display *8 Eco Odometer Display
          *9 Instantaneous Fuel Consumption Display *10 Average Fuel Consumption After Refueling Display
          *11 Drivable Distance Display *12 Average Vehicle Speed After Starting Display
          *13 Dimming Mode Display (While Taillights ON) - -
          A0044QS Pressing the ODO/TRIP DISP switch A0044Y1 Pressing the ODO/TRIP DISP switch for approximately 5 seconds
          A0044RS Pressing the ODO/TRIP DISP switch for approximately 2 seconds - -

      3. Dimming Mode Display Function


        • The brightness level of the combination meter assembly can be displayed on the multi-information display to adjust the meter luminance.

        • While the dimming mode is displayed, the brightness of the meter can be changed by pressing the ODO/TRIP DISP switch for 1 second or more. The brightness of the meter can be adjusted in 4 levels.

        A0044KXC01
        *1 ODO/TRIP DISP Switch - -
        *a Meter Brightness *b 100%
        *c 75% *d 50%
        *e 25% - -