METER / GAUGE SYSTEM


  1. OPERATING CONDITION


    1. Eco Driving Indicator Light (Models with CVT)


      1. Eco Driving Indicator Light starts to operate when all of the following conditions are met:

        Condition Ignition switch is ON.
        Engine is running.
        Shift lever is in D.
        Shift paddle switch is not operating.
        Driving mode is normal.
        When the vehicle is at a speed of about 130 km/h (81 mph) or below.

      2. Eco Driving Indicator Light stops operation when any of the following conditions is met:

        Condition Ignition switch is off.
        Engine is stopping.
        Shift lever is in any position other than D.
        Shift paddle switch is operating.
        Driving mode is not normal.
        When the vehicle is at a speed of about 130 km/h (81 mph) or over.

  2. SYSTEM CONTROL


    1. Front Seat Belt Warning


      1. When the ignition switch is ON, this system detects the condition of the seat belts based on the signals from the front seat belt buckle switch LH and RH and the weight detector sensors.

      2. The front seat belt warning light located in the combination meter is used for both the driver and passenger seats.

      3. After the ignition switch is turned ON, if the driver or front passenger has not fastened their seat belt, the seat belt warning light will begin flashing.

      4. When the seat belt remains unfastened and the vehicle speed reaches approximately 20 km/h (12.4 mph), the seat belt warning buzzer will start sounding intermittently. At this time, the seat belt warning light flashing will change in sync with the intermittent buzzer sound. These buzzer and indicator warnings will continue for approximately 30 seconds until the seat belt is fastened.

      5. If the seat belt still remains unfastened over the approximately 30 seconds, the intervals of the intermittent buzzer sound and flashing light will change, and such warnings will continue for approximately 90 seconds until the seat belt is fastened.

      6. While the seat belt warning light and buzzer are operating, fastening the seat belt will bring them to a stop.

    2. Rear Seat Belt Warning


      1. When any one of the rear seat belt LH, the rear seat belt center or the rear seat belt RH is not fastened, the rear seat belt warning system will turn on the rear seat belt warning light and buzzer provided in the combination meter to urge rear passengers to fasten the rear seat belts.

      2. On 5-door models, the rear seat belt warning light will turn on when approximately 30 seconds have elapsed after the ignition switch is turned to ON and a rear door is operated from open to close, or a rear seat belt is unfastened while the ignition switch is ON.

      3. On 3-door models, the rear seat belt warning light will turn on when approximately 30 seconds have elapsed after the ignition switch is turned to ON, or a rear seat belt is unfastened while the ignition switch is ON.

      4. The rear seat belt warning buzzer will sound when the vehicle speed reaches approximately 20 km/h (12.4 mph) or more while the rear seat belt warning light is on. If the seat belt is not then fastened after approximately 30 seconds have elapsed since the buzzer started sounding, the rear seat belt warning buzzer will sound more loudly than normal for approximately 90 seconds.

    3. Eco Driving Indicator Light (Models with CVT)


      1. When the ECM determines that Eco driving (environment-friendly acceleration operation) is being performed, the ECM outputs Eco Driving Indicator Light illumination request to the combination meter assembly and illuminates Eco Driving Indicator Light.

        A004550E05

  3. FUNCTION


    1. Buzzer Function


      1. The table below shows the buzzer in the combination meter assembly:

        Item

        • Pre-crash Safety System Operation Warning*1

        • Stop and Start System Warning*2

        • Front Seat Belt Warning

        • Rear Passengers Seat Belt Warning

        • EPS Warning

        • Entry and Start System Warning*3

        • Key Reminder

        • Lane Departure Alert Warning*1, *4

        • Pre-crash Safety System Malfunction*1, *4

        • Engine Immobiliser Matching Completion Report

        • Parking Brake On Driving Warning

        • Door Open Driving Warning

        • Sport Sequential Shift Reject Warning*5

        • Light Reminder

        • Turn Flasher Sound

        • *1: Models with toyota safety sense (with pre-crash safety city heater)

        • *2: Models with stop and start system

        • *3: Models with entry and start system

        • *4: Models with toyota safety sense (without pre-crash safety city heater)

        • *5: Models with CVT

    2. Multi-information Display Function

      A0044ZSE01
      Text in Illustration
      *A No shift position indicator is provided in the combination meter without the tachometer *B No shift position indicator is provided in the combination meter with the tachometer
      *C Shift position indicator is provided in the combination meter with the tachometer - -
      *1 Multi-information Display - -

      1. Display Area "a"

        Display Display Item Outline
        A0044NY Clock Display The clock is always displayed.

      2. Display Area "b"

        Display Display Item Outline
        A00453F Outside Temperature Display The outside temperature is always displayed.

      3. Display Area "c"

        Display Display Item Outline
        A0044O5 Odometer Display Displays the odometer.
        A0044Z9 Trip Meter A Display Displays the trip meter A.
        A0044S3 Trip Meter B Display Displays the trip meter B.
        A0044MC Eco Time Display*1 Displays the total amount of engine stoppage time occurring between ignition switch is ON and the subsequent off.
        A0044YC Eco Odometer Display*1 Displays the total amount of engine stoppage time occurring since the last reset.
        A00451X Instantaneous Fuel Consumption Display

        • Displays the value that has been calculated by the combination meter assembly, which is based on the distance driven and the fuel consumption volume.

        • This display is updated constantly.
        A0044TB Average Fuel Consumption After Refueling Display

        • Displays the value that has been calculated by the combination meter assembly, which is based on the distance driven after refueling and the fuel consumption.

        • The combination meter assembly resets the value when determining that the vehicle has been refueled according to the signal from the fuel sender gauge.

        • This display is updated every 10 seconds.
        A0044PY Drivable Distance Display

        • Displays the value that has been calculated by the combination meter assembly, which is based on the elapsed time and distance driven after the ignition switch, has been turned to ON.

        • This display is updated every 1 second.
        A0044N1 Average Vehicle Speed After Starting Display

        • Displays a value that has been calculated by the combination meter assembly based on the vehicle speed signal and the elapsed time since the engine start signal.

        • This display is updated every 10 seconds.
        A00451Y Speed Limiter Control Mode Display*2 Displays the state of the speed limiter control mode.
        A0044OD Pre-crash Safety Warning Timing Display*3 Adjust the pre-crash safety warning timing.
        A004592 Dimming Mode Display Adjust the meter luminance.
        A00450T A0044MJ Eco Driving Indicator Light Customizing Display*4 Customize Eco Driving Indicator Light.

        • *1: Models with stop and start system

        • *2: Models with speed limiter control system

        • *3: Models with toyota safety sense

        • *4: Models with CVT

      4. Display Area "d"

        Display Display Item Outline
        A00454T Shift Position Indicator* Displays shift position P, R, N, D or B of the CVT.

        • *: Models with CVT

      5. Display Area "e"

        Display Display Item Outline
        A00457D Fuel Gauge Display Displays the remaining fuel amount.

  4. OPERATION


    1. Switching the Multi-information Display


      1. The multi-information display changes in the order shown below by pressing the ODO/TRIP DISP switch.

        A0044KKE02
        Text in Illustration
        *A Models with CVT *B Models with Stop and Start System
        *1 ODO/TRIP DISP Switch *2 Eco Driving Indicator Light Customizing Display: Eco On.
        *3 Eco Driving Indicator Light Customizing Display: Eco Off. *4 Odometer Display
        *5 Trip Meter A Display *6 Trip Meter B Display
        *7 Eco Time Display *8 Eco Odometer Display
        *9 Instantaneous Fuel Consumption Display *10 Average Fuel Consumption After Refueling Display
        *11 Drivable Distance Display *12 Average Vehicle Speed After Starting Display
        *13 Dimming Mode Display (While Taillights ON) - -
        A0044QS Pressing the ODO/TRIP DISP switch A0044Y1 Pressing the ODO/TRIP DISP switch for approximately 5 seconds
        A0044RS Pressing the ODO/TRIP DISP switch for approximately 2 seconds - -

    2. Dimming Mode Display Function


      1. The brightness level of the combination meter assembly can be displayed on the multi-information display to adjust the meter luminance.

      2. While the dimming mode is displayed, the brightness of the meter can be changed by pressing the ODO/TRIP DISP switch for 1 second or more. The brightness of the meter can be adjusted in 4 levels.

        A0044KXE03
        Text in Illustration
        *1 ODO/TRIP DISP Switch - -
        *a Meter Brightness *b 100%
        *c 75% *d 50%
        *e 25% - -