METER / GAUGE SYSTEM


  1. OPERATING CONDITION


    1. Eco Driving Indicator Light (Models with CVT)


      1. Eco Driving Indicator Light starts to operate when all of the following conditions are met:

        Condition Ignition switch is ON.
        Engine is running.
        Shift lever is in D.
        Shift paddle switch is not operating.
        Driving mode is in normal.
        When the vehicle is at a speed of about 130 km/h (81 mph) or below.

      2. Eco Driving Indicator Light stops operation when any of the following conditions is met:

        Condition Ignition switch is off.
        Engine is stopping.
        Shift lever is in any position other than D.
        Shift paddle switch is operating.
        Driving mode is not in normal.
        When the vehicle is at a speed of about 130 km/h (81 mph) or over.

  2. SYSTEM CONTROL


    1. Front Seat Belt Warning


      1. When the ignition switch is ON, this system detects the condition of the seat belts based on the signals from the front seat belt buckle switch LH and RH and the weight detector sensors.

      2. The front seat belt warning light located in the combination meter is used for both the driver and passenger seats.

      3. After the ignition switch is turned ON, if the driver or front passenger has not fastened their seat belt, the seat belt warning light will begin flashing.

      4. When the seat belt remains unfastened and the vehicle speed reaches approximately 20 km/h (12.4 mph), the seat belt warning buzzer will start sounding intermittently. At this time, the seat belt warning light flashing will change in sync with the intermittent buzzer sound. These buzzer and indicator warnings will continue for approximately 30 seconds until the seat belt is fastened.

      5. If the seat belt still remains unfastened over the approximately 30 seconds, the intervals of the intermittent buzzer sound and flashing light will change, and such warnings will continue for approximately 90 seconds until the seat belt is fastened.

      6. While the seat belt warning light and buzzer are operating, fastening the seat belt will bring them to a stop.

    2. Rear Seat Belt Warning


      1. When any one of the rear seat belt LH, the rear seat belt center or the rear seat belt RH is not fastened, the rear seat belt warning system will turn on the rear seat belt warning light and buzzer provided in the combination meter to urge rear passengers to fasten the rear seat belts.

      2. On 5-door models, the rear seat belt warning light will turn on when approximately 30 seconds have elapsed after the ignition switch is turned to ON and a rear door is operated from open to close, or a rear seat belt is unfastened while the ignition switch is ON.

      3. On 3-door models, the rear seat belt warning light will turn on when approximately 30 seconds have elapsed after the ignition switch is turned to ON, or a rear seat belt is unfastened while the ignition switch is ON.

      4. The rear seat belt warning buzzer will sound when the vehicle speed reaches approximately 20 km/h (12.4 mph) or more while the rear seat belt warning light is on. If the seat belt is not then fastened after approximately 30 seconds have elapsed since the buzzer started sounding, the rear seat belt warning buzzer will sound more loudly than normal for approximately 90 seconds.

    3. Eco Driving Indicator Light (Models with CVT)


      1. When the ECM determines that Eco driving (environment-friendly acceleration operation) is being performed, the ECM outputs Eco Driving Indicator Light illumination request to the combination meter assembly and illuminates Eco Driving Indicator Light.

        A01UWMAE05

  3. FUNCTION


    1. Buzzer Function


      1. The table below shows the buzzer in the combination meter assembly:

        Item

        • Stop and Start System Warning*1

        • Front Seat Belt Warning

        • Rear Passengers Seat Belt Warning

        • EPS Warning

        • Entry and Start System Warning*2

        • Key Reminder

        • Engine Immobiliser Matching Completion Report

        • Parking Brake On Driving Warning

        • Door Open Driving Warning

        • Sport Sequential Shift Reject Warning *3

        • Light Reminder

        • Turn Flasher Sound

        *1: Models with stop and start system

        *2: Models with entry and start system

        *3: Models with 7-speed sport sequential shiftmatic system

    2. Multi-information Display Function

      A01UWBFE01
      Text in Illustration
      *A No shift position indicator is provided in the combination meter without the tachometer *B No shift position indicator is provided in the combination meter with the tachometer
      *C Shift position indicator is provided in the combination meter with the tachometer - -
      *1 Multi-information Display - -
      Display Area Display Display Item Outline
      "a" A01UW3D Clock Display The clock is always displayed.
      "b" A01UVVG Outside Temperature Display The outside temperature is always displayed.
      "c" A01UW7Q Odometer Display Displays the odometer.
      A01UWNF Trip Meter A Display Displays the trip meter A.
      A01UWAQ Trip Meter B Display Displays the trip meter B.
      A01UW56 Eco Time Display*1 Displays the total amount of engine stoppage time occurring between ignition switch is ON and the subsequent off.
      A01UWAL Eco Odometer Display*1 Displays the total amount of engine stoppage time occurring since the last reset.
      A01UVXN Instantaneous Fuel Consumption Display

      • Displays the value that has been calculated by the combination meter assembly, which is based on the distance driven and the fuel consumption volume.

      • This display is updated constantly.
      A01UW18 Average Fuel Consumption After Refueling Display

      • Displays the value that has been calculated by the combination meter assembly, which is based on the distance driven after refueling and the fuel consumption.

      • The combination meter assembly resets the value when determining that the vehicle has been refueled according to the signal from the fuel sender gauge.

      • This display is updated every 10 seconds.
      A01UVYB Drivable Distance Display

      • Displays the value that has been calculated by the combination meter assembly, which is based on the elapsed time and distance driven after the ignition switch, has been turned to ON.

      • This display is updated every 1 second.
      A01UVY5 Average Vehicle Speed After Starting Display

      • Displays a value that has been calculated by the combination meter assembly based on the vehicle speed signal and the elapsed time since the engine start signal.

      • This display is updated every 10 seconds.
      A01UWBH Speed Limiter Control Mode Display*2 Displays the state of the speed limiter control mode.
      A01UW1F Dimming Mode Display Adjust the meter luminance.
      A01UW0Y A01UWN2 Eco Driving Indicator Light Customizing Display*3 Customize Eco Driving Indicator Light.
      "d" A01UWK0 Shift Position Indicator*3 Displays shift position P, R, N, D or B of the CVT.
      "e" A01UWMP Fuel Gauge Display Displays the remaining fuel amount.

      *1: Models with stop and start system

      *2: Models with cruise control system

      *3: Models with CVT

  4. OPERATION


    1. Switching the Multi-information Display


      1. The multi-information display changes in the order shown below by pressing the ODO/TRIP DISP switch.

        A01UW08E02
        Text in Illustration
        *A Models with CVT *B Models with Stop and Start System
        *1 ODO/TRIP DISP Switch *2 Eco Driving Indicator Light Customizing Display: Eco On.
        *3 Eco Driving Indicator Light Customizing Display: Eco Off. *4 Odometer Display
        *5 Trip Meter A Display *6 Trip Meter B Display
        *7 Eco Time Display *8 Eco Odometer Display
        *9 Instantaneous Fuel Consumption Display *10 Average Fuel Consumption After Refueling Display
        *11 Drivable Distance Display *12 Average Vehicle Speed After Starting Display
        *13 Dimming Mode Display (While Taillights ON) - -
        A01UWJU Pressing the ODO/TRIP DISP switch A01UWQJ Pressing the ODO/TRIP DISP switch for approximately 5 seconds
        A01UWNT Pressing the ODO/TRIP DISP switch for approximately 2 seconds - -

    2. Dimming Mode Display Function


      1. The brightness level of the combination meter assembly can be displayed on the multi-information display to adjust the meter luminance.

      2. While the dimming mode is displayed, the brightness of the meter can be changed by pressing the ODO/TRIP DISP switch for 1 second or more. The brightness of the meter can be adjusted in 4 levels.

        A01UW1AE03
        Text in Illustration
        *1 ODO/TRIP DISP Switch - -
        *a Meter Brightness *b 100%
        *c 75% *d 50%
        *e 25% - -