FUEL SYSTEM


  1. CONSTRUCTION


    1. Supply Pump


      1. The supply pump consists of an inner cam (eccentric cam), an outer cam (polygon ring), 3 plungers, a metering unit and a gear pump. Each plunger is placed outside of the outer cam.

      2. Gear pump pumps fuel to 3 plungers.

      3. Metering unit controls volume of fuel drawn into plungers.

      4. Inner cam drives outer cam.

      5. Outer cam drives 3 plungers.

      6. Plunger pressurizes fuel.

        A01UWF6E03
        Text in Illustration
        *1 Metering Unit *2 Plunger
        *3 Inner Cam *4 Outer Cam
        *5 Gear Pump - -

    2. Common-rail


      1. By storing fuel at a high pressure (30 to 160 MPa), the pump driving torque during the pumping of the fuel under high load condition has been restrained, thus reducing the vibration and noise of the fuel injection volume.

      2. The fuel pressure sensor outputs the fuel pressure signal to the ECM.

      3. The fuel pressure regulator is adjusting the fuel pressure in the common-rail in order to realize the optimum combustion and the reduction of combustion noise.

        A01UWPLE02
        Text in Illustration
        *1 Fuel Pressure Sensor *2 Fuel Pressure Regulator
        A01UWJU From Supply Pump A01UWQJ To Injector

    3. Injector Assembly


      1. A 7-hole piezo type injector assembly is used to precisely control the fuel injection volume and timing.

      2. This injector mainly consists of the piezo actuator, nozzle needle, valve bolt, amplifier piston and valve piston.

      3. An injector compensation value and Data Matrix Code (DMC) containing encoded characteristics of the injector are printed on each injector assembly.

      4. The injector compensation value and DMC contains various pieces of information regarding the injector assembly, such as model code, and injector, such as model code, and injection volume correction.

        A01UVWLE03
        Text in Illustration
        *1 Amplifier Piston *2 Valve Bolt
        *3 Nozzle Needle *4 Piezo Actuator
        *5 Valve Piston *6 DMC
        *7 Injector Compensation Value - -

        Tech Tips


        • If an injector or the ECM is replaced, the injector compensation value can be entered in the ECM via an intelligent tester.


          • When an injector is replaced, enter the injector compensation value of the replaced injector only.

          • When the ECM is replaced, enter the injector compensation value of all injectors. The proper compensation will be made so that the injection volume precision prior to the replacement will remain unchanged.

        • The DMC, which requires a special scan tool, is not used at Toyota dealers.

    4. Fuel Filter


      1. A fuel filter assembly, in which the priming pump, fuel heater and fuel sedimenter level warning switch are integrated, is used.

        A01UW66E02
        Text in Illustration
        *1 Preheating Valve *2 Priming Pump
        *3 Cover *4 Water Level Sensor

    5. Fuel Heater


      1. A recirculation type fuel heater is used. This heater heats the fuel by recirculating the returned fuel, which becomes to have a high temperature by the pumping of the supply pump, to the fuel filter.

        A01UVXFE05

    6. Fuel Sedimenter Level Warning Switch


      1. When the water in the sedimenter section reaches a certain amount, the fuel sedimenter level warning switch comes on, and the warning light in the combination meter assembly illuminates.

    7. Fuel Tank Assembly


      1. The multiplex layered plastic fuel tank is used. This fuel tank consists of 6 layers of 4 types of materials.

      2. A drain mark has been provided at the lowest position of the fuel tank assembly. When dismantling (scrapping) the vehicle, drain fuel by drilling a hole at the drain mark.

        A01UW04E02
        Text in Illustration
        *1 Fuel Drain Mark *2 High Density Polyethylene (HDPE)
        *3 Regrind Material *4 Adhesive
        *5 Ethylene Vinyl Alcohol Copolymer (EVOH) - -
        *a Fuel Tank Wall Cross Section *b Fuel Tank Assembly Outside
        *c Fuel Tank Assembly Inside - -

  2. OPERATION


    1. Supply Pump


      1. Due to the rotation of the inner cam (eccentric cam), the outer cam pushes plunger "A" upward as illustrated below. The force of the spring pulls plunger "C". As a result, plunger "C" draws fuel in, and plunger "A" pumps fuel at the same time.

        A01UW9SE02
        Text in Illustration
        *1 Metering Unit *2 Plunger C
        *3 Plunger A *4 Plunger B
        *a To Common Rail Assembly - -
        A01UWJU Pumping Finish A01UWQJ Suction
        A01UWNT Pumping Start - -

    2. Injector Assembly


      1. The injector assembly operates as shown in the following table.

        Needle Opening (During Injection)

        • The actuator is activated.

        • Valve bolt opens (moves downwards) due to actuator lift.

        • Pressure of nozzle needle tip decreases.

        • Nozzle needle opens (moves upwards).
        Needle Closing (While Stopped)

        • The actuator is deactivated.

        • Valve bolt closes (moves upwards) due to the valve spring.

        • Pressure of nozzle needle tip increases.

        • Nozzle needle closes (moves downwards).
        A01UW19E05
        Text in Illustration
        *1 Piezo Actuator *2 Amplifier Piston
        *3 Valve Piston *4 Valve Bolt
        *5 Nozzle Needle - -
        *a During Injection *b While Stopped
        A01UWJU Fuel - -

    3. Fuel Heater


      1. While the engine is cold, the recirculation valve inside the fuel heater will open due to the bimetal action, so the return fuel will return to the fuel filter and the fuel tank assembly.

        A01UWF5E02
        Text in Illustration
        *1 Preheating Valve *2 Bimetallic Disc
        *a To Fuel Tank Assembly *b From Engine
        *c To Fuel Filter - -

      2. While the engine is warm, the recirculation valve will close due to the bimetal action, so all the return fuel will return to the fuel tank assembly.

        A01UVXBE02
        Text in Illustration
        *1 Preheating Valve *2 Bimetallic Disc
        *a To Fuel Tank Assembly *b From Engine