METER / GAUGE SYSTEM

SYSTEM CONTROL

Front Seat Belt Warning
1. The front seat belt warning turns on the front seat belt warning light and sounds the buzzer in the combination meter to urge the front passenger to fasten their seat belt if it is not fastened.
2. The front seat belt warning blinks each front seat belt warning light individually when the driver does not fasten the driver seat belt or the front passenger does not fasten the front passenger seat belt.
3. The front seat belt warning buzzer sounds when the vehicle speed reaches approximately 20 km/h (12.4 mph) or more while the front seat belt warning light is blinking. If the seat belt is not then fastened after approximately 30 seconds have elapsed since the buzzer sounded, the front seat belt warning buzzer sounds more loudly than normal for approximate 90 seconds.
Rear Seat Belt Warning (Models for Europe)
1. The rear seat belt warning turns on the rear seat belt warning light and blinks the buzzer in the combination meter to urge rear passengers to fasten the rear seat belts when either the rear seat belt LH, the rear seat belt center or the rear seat belt RH is not fastened.
2. The rear seat belt warning light turns on for approximately 30 seconds after the ignition switch is turned to ON, and it also turns on when the rear seat belt is released while the ignition switch is turned ON.
3. The rear seat belt warning buzzer sounds when the vehicle speed reaches approximately 20 km/h (12.4 mph) or more while the rear seat warning light is on. If the seat belt is not then fastened after approximately 30 seconds have elapsed since the buzzer sounded, the rear seat belt warning buzzer sounds more loudly than normal for approximately 90 seconds.

Oil Change Reminder Indicator Light (Models with 1ND-TV Engine)

When one of the following conditions are met: when the running distance exceeds the engine oil change distance; when the engine oil has deteriorated; or when the engine oil amount has abnormally increased over the standard value, the ECM outputs indicator light blinking/illumination request signals to the combination meter assembly and blinks/illuminates the oil change remainder indicator light to urge the driver to change the engine oil.

For details on the conditions in which the oil change reminder indicator light illuminates or flashes, see the 1ND-TV Engine Control.


*1	CAN (V Bus)
*2	OIL CHANGE REMINDER INDICATOR LIGHT
*3	Oil Change Reminder Indicator Light Blinking/Illumination Request Signals
*4	COMBINATION METER ASSEMBLY

Eco Driving Indicator Light (Models with CVT)
1. When the ECM determines that Eco driving (Eco-friendly acceleration) is being performed, the ECM outputs Eco Driving Indicator Light illumination request to the combination meter assembly and illuminates Eco Driving Indicator Light.

FUNCTION

Multi-information Display Function

Display	Display Item	Outline
	Odometer Display	Displays the odometer.
	Trip Meter A Display	Displays the trip meter A.
	Trip Meter B Display	Displays the trip meter B.
	Eco Odo Display	Displays the total amount of engine stoppage time occurring since the last reset.
	Instant Fuel Consumption Display	Displays the value that has been calculated by the combination meter assembly, which is based on the distance driven and the fuel consumption volume. The display updates constantly.
	Average Fuel Consumption After Refueling Display	Displays the value that has been calculated by the combination meter assembly, which is based on the distance driven after refueling and the fuel consumption. The combination meter assembly resets the value when determining that the vehicle has been refueled according to the signal from the fuel sender gauge. The display updates every 10 seconds.
	Drivable Distance Display	Displays the value that has been calculated by the combination meter assembly, which is based on the elapsed time and distance driven after the ignition switch, has been turned to ON. The display updates every 10 seconds.
	Dimming Mode Display (While Tail Lights ON)	Displays the combination meter brightness level.

OPERATION

Switching the Multi-information Display

The multi-information display changes in the order shown below by pressing the ODO/TRIP DISP switch.

Text in Illustration
*1	ODO/TRIP DISP Switch	*2	Eco Driving Indicator Light Customization Display: Eco On (Models with CVT)
*3	Eco Driving Indicator Light Customization Display: Eco Off (Models with CVT)	*4	Odometer Display
*5	Trip Meter A Display	*6	Trip Meter B Display
*7	Eco Odo Display	*8	Instant Fuel Consumption Display
*9	Average Fuel Consumption After Refueling Display	*10	Drivable Distance Display
*11	Meter Brightness Display (While Tail Lights ON)	-	-
*a	ODO/TRIP DISP Switch ON for 5.0 second or more (Models with CVT)	*b	ODO/TRIP DISP Switch ON for 2.0 second or more (Models with CVT)
*c	ODO/TRIP DISP Switch ON for 0.8 second or less	*d	ODO/TRIP DISP Switch ON for 0.8 second or less If ODO/TRIP DISP Switch ON for 0.8 second or more, then reset the Trip meter A.
*e	ODO/TRIP DISP Switch ON for 0.8 second or less If ODO/TRIP DISP Switch ON for 0.8 second or more, then reset the Trip meter B.	*f	ODO/TRIP DISP Switch ON for 0.8 second or less If ODO/TRIP DISP Switch ON for 0.8 second or more, then reset the ECO ODD time.
*g	ODO/TRIP DISP Switch ON for 0.8 second or less If ODO/TRIP DISP Switch ON for 1.0 second or more, then change the Combination meter brightness.	-	-

Dimming Mode Display Function

The brightness level of the combination meter can be displayed on the multi information display to adjust the meter luminance.

While the dimming mode is displayed, the brightness of the meter can be changed by pressing the ODO/TRIP DISP switch for 1.0 second or more. The brightness of the meter can be adjusted in 4 levels.

Text in Illustration
*1	ODO/TRIP DISP Switch	*2	100%
*3	75%	*4	50%
*5	25%	*6	Meter Brightness